John Deere 535 baler
What FARM SHOW readers say · 14 Best Buys0 Worst Buys · Farm & Livestock Equipment
John Deere 535 baler
14 Best Buys0 Worst Buys“My used Deere 535 baler is still in good shape. It has an automatic tie system and bale kicker, so each bale requires two motions - depressing the clutch to stop and opening the gate hydraulically, which saves wear and tear on artificial knees and arthritic hands.
“My Ritchie 300 fiberglass drinker is my worst buy. It’s rated to handle 125 beef cows. However, the drinking reservoir is so narrow that livestock have to turn their heads 90 degrees just to get at the water. Even then, their mouth doesn’t fit and they dribble and slurp so much water that during the winter an ice cone develops around the drinker. To prevent dangerous slips, I have to chip the ice away twice a week.”
“It gets a lot of hard use, but we’ve had very little trouble with it,” says David about his 1998 Kawasaki Prairie 400 4-WD ATV. “The company took care of a few minor problems. I have an artificial leg so I appreciate the automatic transmission. The floor board design is also helpful. There are more powerful ATV’s on the market, but after riding them for a while I really came to appreciate this machine.”
“My 1979 Ford F-250 4-WD pickup is a best buy. It has been all over the country and has been in a few tangles that required some hospitalization, but it came away better for it all.
“My 1972 Deere 4620 and 3020 tractors are dependable and are best buys.
“I’m well pleased with my Deere 535 round baler. I’ve owned Hesston and Gehl models before but this is the best.
“My biggest disappointments have been with my Case-IH 470 and 480 21-ft. disks. In my opinion, these discs were nothing but glorified sheet metal. I sold both of them and bought a Deere 14-ft. model. I can cover the same amount of ground as I had been covering with the two Case-IH models, and do a better job. No problems.
“My Hesston 6650 swather is a disaster. I don’t understand how a company can even put its name on a machine like this. I wish I still owned my Deere 1600 14-ft. hydraswing swather.
“I was given a kit to raise the rear bench seat in my 1985 Ford Supercab pickup. It was purchased through J.C. Whitney and was something that I had asked for. However, it’s a worst buy. The bolt holes in the brackets were about three sizes too big, the washers were too small, and I had to reshape some of them to fit. I was really disappointed with it.”
“It’s always ready to bale hay when I am,” says Richard, well pleased with his Deere 535 round baler.
“Our best buy is our 1993 Deere 535 round baler. We’ve used it to make more than 10,000 bales and it still works great. It makes nice, tight, uniform bales. The bale size and amount of twine used can be adjusted easily. Also, the bale monitor lets the operator know which side of the baler needs hay and when the tying has started. We’ve had to replace only two bearings. My only suggestion is that they make the pickup teeth easier to change. Also, the hitch could be built stronger.”
Robert likes his 1993 Deere 535 big round baler equipped with surface wrap, converging wheels, and hydraulic pickup lift. “It’s a simple and clean machine that has been trouble-free since day one. The ‘bale track’ monitor is the best on the market for making perfect bales. The only modification I made was to install an electric row shut-off solenoid valve off an old planter, which allows me to control the start of the tieing by simply pushing a button in the cab.”
“My best buy was my Deere 535 round baler. “My worst buy is my Marliss no-till drill. I followed the company’s suggestions on how to get it to plant at the right depth for two years. I wanted wider press wheels but the company would only sell them to me at $61 apiece. I finally bought new wide press wheels from Shoup Mfg. for $26 apiece. Now I have to solve the problem of having to change two sets of sprockets and chains whenever I switch from planting oats to beans. I also had to straighten out the guides on the press wheel springs - the guides were welded together wrong at the factory and are half worn out after planting only 200 acres.”
David nominates his 1994 Deere 535 round baler as his “best buy”. “My brother and I have used it without any problems to bale straw, hay, and corn stalks. It’ll make whatever size bale we want. It doesn’t cost any more than other balers we priced.”
“My 1995 Ford F-150 4-WD pickup is the nicest vehicle I’ve ever owned. It has a quiet, smooth ride and the automatic transmission shifts smooth. The 351 cu. in. engine has a lot of power but could be more fuel efficient. “My 1996 Deere 535 round baler, coupled with my Deere 7800 MFWD tractor equipped with a powershift transmission, is a pleasure to operate. Makes solid bales that weigh twice as much as the ones we made with our old Deere 510. I really like the net wrap. Holds prairie hay together and virtually eliminates spoilage.”
Mike Scanlon, Oskaloosa, Lowa: “I'm impressed with my Posi Lock gear puller. It’s easy to use and doesn’t slip off the pulley or gear. “I’ve also had good luck with my 1993 Deere 535 round baler.”
Alton Lerwick, Lyman, Neb.: “My worst buy is my 1990 Ford F-350 4-WD pickup equipped with a 7.3-liter diesel engine. It has 58,000 miles on it. The trouble began when the clutch went out at about 20,000 miles. The company said that was ‘normal wear and tear’ and wouldn't cover it under their 60,000 mile drivetrain warranty. Since then the clutch has gone out again, the clutch master cylinder has been replaced twice, and the power steering has been repaired three times. It’s gone through three starters, four alternators, and five sets of batteries and the transfer case has been rebuilt three times. The rear seals leaked and ruined the rear brakes, The radiator fins are so close together that nothing can pass through them. As a result, the screen plugs up and has to be removed and cleaned on a regular basis, The pickup frame broke on one side and now paint is peeling off the hood. I’m a real skeptic whenever I see Fords advertised as ‘Ford tough,’ “My Deere 535 round baler is reliable. The bales start easy and are solid.”
Lester Gehman, Manheim, Penn.: “My 1989 Dodge diesel pickup is my best buy. The Cummins diesel engine starts easy, runs like a top, and pulls like an 8-horse team. It gets 20 to 22 mpg. Takes only half as long to fill the fuel tank as the Ford we owned before.” Norman Farrington, Mechanicsville, Iowa: Norman nominates his 1991 New Idea 5209 rotary hay mower as “best buy”. “All I do is get on and go. It does a great job at fast speeds. “My 1988 Case-IH 7120 tractor handles comfortably, has a quiet cab, and is easy to service. The powershift transmission performs well. “My 1992 Deere 535 round baler with net wrap is built strong to withstand damage on rough ground and makes good bales at high speeds. The netting speeds up baling and sheds water. Works great as long as it goes on right. However, I’ve had problems with it catching and tearing.”
Kenneth Dickneite, Iberia, Mo.: Kenneth’s the satisfied owner of a 1992 Deere 535 round baler. “This baler is built simple and is easy to operate and maintain, It consistently makes tight, uniform bales. Even with all the rain we had last year there was little waste on the outsides and bottoms of the bales.”
Laurence Pacey, Miltonvale, Kan.: Laurence nominates his 1991 Deere 535 net wrap baler as his best buy. “We’ ve had good results baling our own hay and also custom baling.”
Albert Chlan, Webster, Minn.: Albert's “best buy” is his Deere 535 round baler equipped with net wrap. “It lets me switch from net wrap to twine in no time and eject the bale without having to back up.
Own a John Deere? Tell FARM SHOW how it’s held up.
Your report could appear in a future issue.