Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Brands › Northern Tool

Northern Tool: what farmers say

29 reports in FARM SHOW · 14 Best Buys15 Worst Buys

Northern Tool (general)

11 Best Buys12 Worst Buys
Worst Buy
Eddie Lehmann, Bynum, Texas · Vol. 50, No. 2 (2026), p. 15

“I’ve had many Ford pickups over 60 years. I drove a 2002 F-250 SuperCab with a 5.4 engine and an automatic transmission. In 175,000 miles, I never touched the engine or transmission. Both were dry with no leaks. I sold it in 2024. It now has over 300,000 miles and is still going. People tell me this is unreal. I still drive Fords. Treat them like a good woman, and they’ll stay by your side.

“FARM SHOW’s ‘Best, Worst Buys’ section is a best buy. I’ve avoided some bad buys and found some good ones by reading it.

“Mahindra tractors have been good buys. I bought my first in 2002 and now own two. With regular service, they keep going.

“I’ve been using Miller portable welders for 50 years. I went to them because Lincoln didn’t have AC for hand tools.

“On the negative side, anything I’ve ordered off Facebook has been junk, or I never received it, even though my credit card was charged. There’s no way to contact them.

“I bought a hydraulic and cable lift for a pickup or trailer bed from Northern Tool. I didn’t open the box for a year. When I went to assemble it, the packaging didn’t include a base section. I went back to Northern Tool, and the manager told me they had stopped carrying those. They wouldn’t give me my money back even though I had my receipt. I tell everybody to beware of Northern Tool.”

Worst Buy
Alfred O. Ohlson, New Salem, Mass. · Vol. 45, No. 4 (2021), p. 12

“It’s easy to maneuver and has excellent power for my small farm’s needs,” says Alfred about his 2017 Massey Ferguson 4608L loader tractor. “This is the second Massey I’ve owned, and both are best buys.

“The bolt-on bucket forks I bought from Northern Tool won’t stay in position for lifting pallets, no matter what I do to secure them.”

Best Buy
Robert L. Green, Gettysburg, Penn. · Vol. 45, No. 2 (2021), p. 14

Robert’s impressed with Permatex Cold Weld bonding compound, a 2-part adhesive and filler system that eliminates the need for welding or brazing (www.permatex.com). “Works good on worn 2-cylinder flywheels and crankshafts. Just clean them, apply Permatex, adjust and tighten the flywheel, and let the epoxy cure,” he says. “If you have to remove the flywheel later, you can use a 12-ton jack to pull it off.”

He’s disappointed with the 2020 Quincy 5-hp. air compressor he bought from Northern Tool. “A 2 1/2-in. plug on top of the tank consistently leaked air where the air regulator taps into the plug. The problem is that the plug has an O-ring that won’t seat properly. I called the factory technician and they sent me a smaller O-ring. It worked better, but at 100 lbs. pressure the O-ring pushed out again. I tried using ‘pipe dope’ to hold it in place but that didn’t help, either. Then I tried using Permatex sealant (www.permatex.com). Now the compressor works great again.”

Best Buy
Ron Schupbach, Brodhead, Wis. · Vol. 44, No. 6 (2020), p. 15

“I bought a KingKutter 3-pt. mounted rough cut mower at Northern Tool and use it with my Deere 2025 tractor. It works good on tall, tough weeds and brush, but it’s not a true bush hog so I have to be careful not to overdo it.

“In the past I purchased a fair amount of merchandise from Northern Tool, but not anymore. I ordered a log grappling hook and also a cover for my lawn tractor. I received the grappling hook but not the cover. I called the company numerous times over 2 months, but they just passed the buck from one person to another. No one ever told me why I never got the cover or got a refund on my credit card.”

Best Buy
Lyle Smith, Defiance, Ohio · Vol. 44, No. 1 (2020), p. 12

“The loader bucket forks I bought at Northern Tool are rated at 2,600 lbs., but mine bent carrying just a 760-lb. load. The company replaced the forks at no cost, but now I’m afraid to load them with more than 500 lbs. On the other hand, I bought a set of 14,000-lb. rated forks for my backhoe loader, and they work fine.”

Best Buy
Melvin Thies, Jacksonville, Ill. · Vol. 42, No. 4 (2018), p. 14

“The 2015 Kubota X1100C 4-WD utility vehicle I bought used two years ago is nicer to use than a riding mower, goes a lot faster, and has a nice heated cab. It’s also easier to get in and out of and has more power.

“I welded a metal hook on a ball hitch that attaches to the vehicle’s receiver tube. I use it to pull small brush out by the roots. This machine has enough power to pull out most of the brush on our farm.

“The shrub grubber I bought from Northern Tool works great to remove shallow-rooted clumps of brush (www.northerntool.com). It consists of three 4-ft. long chains equipped with 1/4-in., V-shaped gripping links that are attached to two different size rings. You wrap the chains around the brush and through the larger ring, and then attach a pulling chain to the smaller ring.

“The company also offers a brush grubber that works great to clear small trees and brush. It comes with two rotating pads, with eight gripping teeth on each pad to make sure that its grip never slips off the tree trunk. The jaws close tighter the harder you pull.”

Worst Buy
Ben Kauffman, Chesapeake, Va. · Vol. 39, No. 4 (2015), p. 15

Ben likes his 2014 Milwaukee MI8 FUEL hammer drill impact wrench. “One day I used the drill to actually drive my riding mower into a shed and up a ramp by using a socket to drive a transmission pulley nut. I love this tool’s power. I recently bought a Milwaukee brushless sawzall and it works great, too.”

On the “worst buy” side, he lists the Performance Tool pistol grip grease gun from Northern Tool. “The directions didn’t make sense. I finally got it loaded, but something inside the grease gun went bad and messed everything up. I never was able to get much grease out of the gun and ended up throwing it away. I think I’ll go buy a Milwaukee cordless grease gun.”

Best Buy
Kevin Ericson, Axtell, Neb. · Vol. 39, No. 1 (2015), p. 13

“I like the 20-ton air-over-hydraulic jack I bought at Northern Tool. I bought it to replace the 20-ton hydraulic jack that came with my shop press, and find that it has much more power and operates faster. It cost just over $130, including shipping. I was so impressed that I bought another jack from them to use around our farm.”

Best Buy
Jim Harkness, Laingsburg, Mich. · Vol. 39, No. 1 (2015), p. 14

“I bought an All-Power 6500-watt generator from Northern Tool, but the filler cap was so low to the tank that I couldn’t get it open without using a large pair of channel pliers. The machine is so loud that when it’s running I can’t even hear myself scream. Also, the muffler disintegrated within the first few hours of use.”

Worst Buy
Joe Hummert, Jonesburg, Mo. · Vol. 38, No. 2 (2014), p. 15

“I’ve used my 2012 Stihl 026 chainsaw equipped with an 18-in. bar to cut more than 10 cords of wood, without a single problem. It’s easy to service and has plenty of power. I can service anything on it with one wrench. It’s a good, lightweight saw.

“The All Power 3,500-watt propane portable generator I bought at Northern Tool is my worst buy. When I put a 15-amp load on it the motor killed. By my calculations 3,500 watts equals 28 amps, so this generator doesn’t perform as advertised.”

Best Buy
Merrill J. Smith, Deer Park, Wash. · Vol. 36, No. 5 (2012), p. 15

“I’ve had great success with Makita tools, both corded and cordless, including drills, a chopsaw, 7.2-volt flashlight, sawzall, and 1/4-in. hex impact driver. The flashlight was left outside on the ground all winter underneath 4 ft. of snow, but when I found it the following spring it was still charged and worked fine. I use the impact driver nearly every day and haven’t had to recharge the lithion battery in it yet after almost a year.

“The battery-powered sprayer I bought at Northern Tool would hardly spray far enough out to clear my feet, and the batteries lasted only about 20 min. before they went dead. I also bought a water well pressure tank from Northern Tool. It was advertised as an 80-gal. model but turned out to be only 35 gal. I called to see why and was told the ad meant it ‘performed like 80 an gal.’. What a farce.”

Worst Buy
Richard Green, King Ferry, N.Y. · Vol. 36, No. 4 (2012), p. 13

“I like my Kaito Voyager dynamo and solar-powered radio with short wave and AM FM as well as NOAA weather bands (ph 866 524-8676; www.kaitousa.com). I have a collection that includes about 38 various radios, but this little unit is the best. It sells on the company website for $69.95, but I bought mine from Sportsman Guide for $49.97 (www.sportsmansguide.com). Fortunately this radio doesn’t have digital tuning. It’s really designed for sane, simple use and runs for hours when the charge mode is used. It’s also battery, solar and AC-powered. I really like it.

“The bar-mounted chainsaw sharpener I bought at Northern Tool is my worst buy. The owner’s manual doesn’t come with instructions on how to set up and use this product. I made 13 different phone calls to the company’s customer service department and spoke with many ‘supervisors’ in customer service, two of whom hung up on me. I finally received an envelope with written instructions for the product’s use.”

Worst Buy
Patricia Peacock, Sulphur Springs, Texas · Vol. 34, No. 5 (2010), p. 14

“The dual head turbo propane torch I bought from Northern Tool is my worst buy. I couldn’t get the torch to work so I kept sending it back for a new one. They made me pay to send it back after the first one. Now I’m on my third model, which if I sent it back in exchange for another, will have cost me $69. That’s way more than the $39.99 I paid for the original tool. But the company won’t refund my money unless I pay to ship this model back. I won’t buy anything from them again.”

Worst Buy
Bill Barg, Cincinnati, Ohio · Vol. 34, No. 4 (2010), p. 14

“My 1974 Kubota L225 tractor still runs great, and the engine has never lost one drop of oil.

“My worst buy is the 1998 hot water pressure washer I bought from Northern Tool. I paid $2,200 for it. The first time I used it all the joints leaked. I took it to the place that did the warranty work, but the company wouldn’t pay because they said the problem was due to normal wear and tear. The washer has been in repair shops ever since. The company won’t stand behind the warranty, and parts are impossible to get.”

Best Buy
Tom Minkstein, Manlius, N.Y. · Vol. 34, No. 4 (2010), p. 15

“The 2,000-watt inverter I bought at Harbor Freight is my best buy. I direct-wired the inverter to my Bush Hog Trail Hand 4400 utility vehicle and use it to operate any 120-volt tool that I need out in the field. It’s faster and easier than dragging out a generator. I just open the hood and plug the tool in. No muss, no fuss.

“I purchase a lot of tools and equipment from Northern Tool and haven’t been disappointed yet. The company’s sales associates are knowledgeable and always take the time to help. If anything breaks or has to be replaced, they always find a way to help. I highly recommend this company.”

Best Buy
Mike Sinnott, Stratford, Ct. · Vol. 34, No. 1 (2010), p. 14

“The set of cobalt twist drills I bought last year from Northern Tool is my best buy. I use these drills with cutting oil for threading pipe, and they cut through steel like there’s no tomorrow. Forget titanium or high speed steel drills – I’ll stick with cobalt.”

Worst Buy
Ken Marcotte, Rosemount, Minn. · Vol. 34, No. 1 (2010), p. 14

Ken’s the proud owner of a 2007 Deere 7930 tractor equipped with a model 746 front-end loader. “I bought this tractor equipped with Infinitely Variable Transmission (IVT) and Triple Link Suspension (TLS), a combination that has resulted in the best tractor I’ve ever operated. IVT has to be the best invention ever.

“This tractor is awesome when used with a grain cart, because it matches combine speeds perfectly and is extremely smooth when unloading into trucks. TLS improves the ride, especially with the loader on. The tractor has tremendous hydraulic flow and outstanding power bulge and, with IVT, the fuel usage has been outstanding for a 180 hp tractor. The tractor itself has been trouble-free.”

On the negative side, he lists high pressure hose that he bought at Northern Tool. “The third time I used the hose it started leaking through the seam. When I tried to return the hose the company told me they only warranty pressure hoses for 30 days. It didn’t matter that there was no physical damage to the hose. I find Northern products to be poor quality, and their customer service is even worse.”

Worst Buy
Robert Mann, Somerset, Calif. · Vol. 33, No. 6 (2009), p. 14

Robert’s impressed with his 1997 Dodge 2500 pickup equipped with a Cummins diesel engine. “It runs great and handles my 28-ft. fifth wheel trailer and farm produce loads with ease. It gets 20 mpg on the freeway and 15 mpg in town or when driving in hilly terrain. It has required two expensive repairs, though, to the rear axle seals and when a rollover protection switch had to be replaced.

“I’m disappointed with a battery-operated pruning chainsaw that I bought at Northern Tool. The battery lost power with only a few minutes of use and then, after a few charges, the tool wouldn’t work at all.”

Worst Buy
Bill Mobley, Hubbard, Texas · Vol. 33, No. 4 (2009), p. 14

“The 10-ton manually-operated log splitter I bought from Northern Tool is my worst buy. It has a 2-speed pump that builds up to 10 tons of pressure and operates by using two steel handles. However, it won’t split logs.”

Worst Buy
Alan Davis, New Florence, Penn. · Vol. 33, No. 4 (2009), p. 15

“I use my 1968 Deere STX 38-in. riding mower to cut my own lawn as well as a 2-acre church lawn. It’s well made. No complaints.

“The winch I bought from Northern Tool was supposed to pull two tons, but it didn’t last a month. We were only using it to skid trees from 4 to 6 in. in diameter.”

Best Buy
Gerald T. Fedler, Fort Madison, Iowa · Vol. 32, No. 5 (2008), p. 14

“I’m well pleased with my 1999 Cub Cadet 3225 garden tractor. It cuts well and has plenty of power, even in 6-in. tall or taller grass. Makes mowing a fun job. The deck itself is a maintenance nightmare, but the tractor has been mostly trouble-free.”

He’s impressed with an engine he bought from Northern Tool (ph 800 221-0516; www.northerntool.com). “I needed a new engine for a pull-type mower. I priced engines locally first, then checked the prices in my Northern Tool catalog. The engine was less than half price through Northern so I figured I could wait the few extra days for the delivery. I ordered it through their website at 1:30 on Monday afternoon, and UPS pulled into my yard at 11:30 Wednesday morning. By 2 p.m. I had the engine mounted and ready to run.”

Best Buy
Bob Wurst, Waynesboro, Tenn. · Vol. 31, No. 5 (2007), p. 15

A cast iron hydraulic pump that he bought from Northern Tool rates as Bob’s “best buy”. “I’ve got an older Kubota tractor and the hydraulic pump went out on it. Kubota wanted about $600 for a new pump, which I couldn’t justify. I had to do some replumbing in order to install this pump and I had to mount a pulley on the engine crankshaft so I could belt-drive the new pump. Works great and cost me just a little more than $100.”

Worst Buy
Tommy Scoggins, Rock Hill, S.C. · Vol. 30, No. 4 (2006), p. 14

“My 2002 New Holland TN65 tractor has never been back to the dealer and is my best buy. My two brothers also own a TN65. They’re excellent, dependable tractors.

“I bought a pack of chain saw files designed to fit into a drill from Northern Tool, and it’s my worst buy. The files disintegrated before I could get the chain sharp. This company has gone to buying a lot of products from China, and as a result the quality has dropped tremendously.”

Northern Tool 12-volt d.c sprayer pump

1 Best Buy0 Worst Buys
Best Buy
Russ Zortman, Woodland, Penn. · Vol. 40, No. 1 (2016), p. 13

“I bought my Northern Tool 12-volt D.C. sprayer pump last April but by July it had stopped working although the motor still ran. When I called the company a rep asked if I could handle swapping out the pump head by myself and I told him I could, so he sent a new pump head and told me to throw the old one away. There was no charge at all, and I had my part in 3 days. This company is a pleasure to deal with.

“I made the mistake of buying a Buffalo Tools 7,000-watt diesel generator. My local Tractor Supply Co. store was selling them for about $1,600, which seemed cheap for a diesel generator. I soon found out why. After a few hours of use it broke down. From then on it was almost always breaking down. The company was willing to send me parts so I could make a couple of repairs myself. However, when I had to replace the rotor, stator, and control panel, they said I would have to pay $700 for parts. “I told them the generator was less than 6 mo. old, but they said these problems were somehow my fault and therefore weren’t covered by the warranty. It isn’t the right shape to make a decent boat anchor, so I can’t imagine any possible use for it”.

Northern Tool 200 amp

0 Best Buys1 Worst Buy
Worst Buy
Steven M. Yoder, Reedsville, Penn. · Vol. 39, No. 5 (2015), p. 15

“My Miller Spectrum 625 plasma cutter cuts up to 5/8-in. thick steel, and my Millermatic 250 Mig welder welds up to 1/2-in. material. Both work great.

“My Northern Tool 200 amp AC stick welder and my 140 wire welder were both worst buys.”

Northern Tool 24-volt 1/2-in drive

1 Best Buy0 Worst Buys
Best Buy
Charlie Card, Prosser, Wash. · Vol. 37, No. 1 (2013), p. 15

“My 2010 Northern Tool 24-volt, 1/2-in. drive impact wrench is as handy as a shirt pocket. We use it way more than we ever thought possible. The battery holds its charge so it can do lots of work.”

Northern Tool Nothing matched

0 Best Buys1 Worst Buy
Worst Buy
Dale M. Walker, Jr., Flemington, N.J. · Vol. 30, No. 5 (2006), p. 12

Dale nominates his 2004 Landtrac 390 HST 4-WD tractor equipped with a front-end loader as his “best buy”. “It’s built with the user in mind - everything is on it is very handy and reliable. It fits right in on our farm.

“My worst buy is a bolt-on hoist kit designed to turn a pickup into a dump truck, which I bought from Northern Tool. Nothing matched up according to the directions. Installing it turned into a big mess. I called the dealer five times but got no help. After some drilling, torching and welding, eventually I was able to get the hoist to work.”

Northern Tool These saws seem

0 Best Buys1 Worst Buy
Worst Buy
Bob Andrews, Haines, Alaska · Vol. 29, No. 6 (2005), p. 15

Bob enjoys browsing through his E & R seed catalog (E & R Seeds, Monroe, Ind. 46772 ph 260 692-6071). “E & R Seeds has great prices, with products that are a good value for the dollar. I’ve purchased both seeds and plants and find their quality to be excellent. I do wish the company had a website and email address.

“Clear Span greenhouses sold by FarmTek are also best buys (Dyersville, Iowa ph 800 327-6835; www.farmtek.com). These buildings are easy to assemble and disassemble, and they’re built tough. I’d definitely purchase another one.”

On the “worst buy” side, he lists the meat saws he purchased from Northern Tool. “These saws seem to have a sturdy frame and a comfortable handle. However, the blades have no adjustment. When installed, they’re much too loose, which causes a crooked cut. As far as I can see, they’re not much good for anything.”

Northern Tool chainsaw sharpener

1 Best Buy0 Worst Buys
Best Buy
John M. Beech, Chatom, Ala. · Vol. 34, No. 2 (2010), p. 14

John’s impressed with his Northern Tool chainsaw sharpener (ph 800 221-0516; www.north-erntool.com). “This tool comes with three grinding wheels and can sharpen most chains to a razor sharp edge. I have three saws on my farm and used to dread sharpening the chains. Now it’s a fun job.

“My 2008 Dodge diesel Megacab dually pickup is a worst buy. The engine stops whenever there’s a rain shower. The problem started after I took the pickup in for a recall at about 20,000 miles. The engine stopped 6 different times, and three of them happened while I was pulling a trailer. The pickup has been in the shop 6 times for this problem. It has gone through two computer replacements and four ‘check engine’ light resets, but it still doesn’t work right. This is my first Dodge pickup, and it’ll be my last, too.”

Read every report in full

FARM SHOW has run reader Best & Worst Buys since the beginning.

Subscribe to FARM SHOW