Case: what farmers say
561 reports in FARM SHOW · 481 Best Buys82 Worst Buys
Case (general)
200 Best Buys47 Worst BuysAllen Beiler, Stuarts Draft, Va.: Allen's impressed with his 1993 Case-[H Maxxum 5240 tractor. “It’s the best tractor on the market in its horsepower class. The 4-speed powershift transmission, smooth-running Cummins diesel engine, convenient controls, and excellent visibility make it a pleasure to operate. A lot of thought went into “It's the best tractor on the market in its horsepower class.” the design of this tractor “My 1989 Chevrolet 4-WD pickup is my worst buy. First we had trouble with the electronic ignition. Then when we did get the pickup running it didn’t have enough power, It also ran rough and guzzied a lot of gas. Last year the automatic transmission went out and this year we had to re place the engine. Now we finally have a decent truck again,”
Chris Tschumperlin, Watkins, Minn.: A 1994 Case-IH 8530 small square baler equipped with an 8511 belt thrower rates as Chris’s “best buy”. “Last fall we used it to make 1,600 corn stalk bales for bedding. Our old baler never tied properly when making corn stalk bales, but this one has no problem with them, This year we put up 12,000 bales of 23% protein alfalfa without rain, No problems, [ haven't even broken a shear bolt yet.”
Chuck Younger, Columbus, Miss.: Chuck likes his Case-TH 7210 (130 hp) and 7220 (150 hp) Magnum front wheel assist tractors, “Both are solid tractors that pull great and are comfortable to drive.” On the “worst buy” side, “My Yamaha Kodiak 4-WD ATV equipped with a 400 ce gas engine is a piece of junk. The driveshaft wore out in less than a year, The company wouldn't pay for the repair so I called its trouble shooter and got no help there, either, so I spent $1,000 on it the first year My Polaris Magnum 425 2-WD ATV is equipped with a 4-stroke engine and can go “The driveshaft wore out in less than a year.” places in 2-WD that the Yamaha can’t go in 4-WD.”
Richard Bohn, Luck, Wis.: “It has a lot of power and a roomy, quiet cab,” says Richard, pleased with his 1977 Case-TH 1086 tractor. “My Knight 712 manure spreader can spread manure in 35° below temperatures with no problems. It’s also a best buy.”
3960 chopper which he bought used, "Even when we put two windrows together the machine is still hungry. It has reduced our chopping time by half or more “My Stihl chain saw is a best buy. It's sull going strong after 18 years. I've used it to cut 14 cords of wood a year to heat our house, as well as to cut lumber and pulp.” Tom Tate, Sublimity, Ore.: “My 1980 Bush Hog heavy duty (5-ft. tandem disk does a good job of penctrating our heavy grass seed sod due to the weight on cach disc blade. It does as good a job as an offset disk, and by swinging the gangs backward I can reduce the angle of the blades so can use it to do finish work. It's well built. “My 1987 Chevrolet S-10 4-WD pickup, which bought used with all the ‘bells and whistles’, is my worst buy, The V-6 engine is hard on fuel, and reverse gear on the automatic transmission failed immediately. The transfer case leaks as does the transmission. I've had nothing but trouble with the gauges - the oil pressure sensor has been replaced three times and now it's out again. Also, the transfer case shift has broken the gear shift linkage twice.”
Alton Lerwick, Lyman, Neb.: “My worst buy is my 1990 Ford F-350 4-WD pickup equipped with a 7.3-liter diesel engine. It has 58,000 miles on it. The trouble began when the clutch went out at about 20,000 miles. The company said that was ‘normal wear and tear’ and wouldn't cover it under their 60,000 mile drivetrain warranty. Since then the clutch has gone out again, the clutch master cylinder has been replaced twice, and the power steering has been repaired three times. It’s gone through three starters, four alternators, and five sets of batteries and the transfer case has been rebuilt three times. The rear seals leaked and ruined the rear brakes, The radiator fins are so close together that nothing can pass through them. As a result, the screen plugs up and has to be removed and cleaned on a regular basis, The pickup frame broke on one side and now paint is peeling off the hood. I’m a real skeptic whenever I see Fords advertised as ‘Ford tough,’ “My Deere 535 round baler is reliable. The bales start easy and are solid.”
Tom Merrigan, Vermillion, 8. Dak.: A 1991 Case-TH 7120 front wheel assist tractor rates as Tom’s “best buy”, “It’s been a lifesaver during the wet springs we’ ve had in two of the last three years. It has a lot of power and traction so we can stay out of trouble in wet fields. It’s easy on fuel and can do any task on our farm. We wouldn't farm without it.”
Lester Myers, Marquand, Mo.: Lester's happy with his 1992 Case-IH 395 tractor, “I especially like the shuttle shift transmission but I wish it had more than 8 speeds. The power steering is the best I've ever used,”
Jim Eller, Sun River, Mt: A used Deere 4050 tractor equipped with a 158 loader and grapple fork is Jim's “best buy”, “It’s as reliable and efficient as a 4020 but with less noise. The quad range isn’t as efficient as the powershift transmission, but it’s dependable. The tractor is easy to work on and the turbocharged engine has a lot of power and starts well in cold weather. The cab is quiet and well designed with easyto-operate controls.” On the negative side, Jim lists his 1995 Case-TH 1594 front wheel assist tractor equipped with a Case-IH loader, “From the first day we had trouble with the hydraulics, and the tractor is an absolute pain to service. The cab is designed poorly - controls are hard to get at. It doesn’t start reliably in cold weather even though it’s in the shed and plugged in 24 hours a day. However, it is fuel efficient and I like the front wheel assist. Dealer and company support has been marginal.”
Roger Kirby, Lamont, Okla.: “It really eats hay and has been virtually troublefree,” says Roger about his 1991 Case-TH 8580 big square baler. “1 bought it used after it had already made 20,000 bales. I also like the big baler seminars put on by the Maize Corp., Maize, Kan, They also do’ service work on big balers, I can call them at 11 0’ clock at night and get help.”
Marvel Erion, Alta Vista, lowa: “My 1995 Case-TH 950 22-in. row planter places seed accurately and at an even depth. It’s truly an ‘Early Riser’. Seed comes up fast. “I’ve had numerous problems with the powershift transmission on my 1992 CaseTH 5140 tractor. Sometimes it works and sometimes it doesn't. The electronics on it have problems. Things have only been partially fixed.”
Kenneth Fricke, Corder, Mo.: “I like my 1971 Deere 4520 tractor with a powershift transmission, I bought it used and it still works great, “My worst buy 1993 Case-IH 4200 15ft. Combo-Mulch finisher won't create an even seedbed, The dises on front bring corn stalks toward the center and pile them there in a ridge which the cultivator in back can’t level out. The dealer has tried to fix the problem with no luck. Company representatives admit all 15-ft. models have this problem but won't do anything about it.”
Thomas N. Johnson, Rossville, Tenn.: “It’s the best mower I’ve ever had,” says Thomas, owner of a Taylor Way 1500 15ft. hydraulic batwing rotary mower. “My new Case-TH 900 no-till planter is one of the best planters ever built. It does a good job planting under almost any conditions and doesn’t even need no-till coulters. It’s truly a fine row crop planter.”
Laurence Sanderson, McLouth, Kan.: A 1993 Case-IH 5220 tractor and a 1980 Vermeer 6S0F round baler are two of Laurence’s “best buys”. “The Case starts at low temperatures with no problems. The 3-pt. has tremendous lift capacity, so much that I’ve already bent two mounted implements. The Cummins diesel engine is very fuel efficient. The Vermeer baler is built like a tank. I've had to replace only two bearings and the drive chain in 15 years. In my opinion it makes a tighter wrapped bale than any other baler on the market,”
Archie T. Thompson, Whitaker, N.C.: A Case-TH 3900 19-ft., 6-in. disk is one of Archie's “best buys”. “It’s a well-built piece of equipment that does an excellent job of cutting and turning under crop residue. It's a Jot better than the TH 475 disk I traded in. I would recommend this disk to anyone. However, you should have at least a 140 hp tractor to pull it.”
Leon Jones, Britton, S. Dak.: A 1993 New Holland 308 manure spreader is one of Leon's “best buys.” “It does a very even job of spreading, no matter whether it's handling liquids or solids with a moderate amount of straw.” On the negative side: “We've put 3,600 hours on our 199] Case-IH 7140 front wheel assist tractor, In four years, we've had to replace both front and rear wheel seals, completely overhaul the engine after it threw a rod, and fix a slipping transmission, We've also had to replace both load boxes on the 3-pt. hitch. Fortunately, our dealer and the company have been very good about fixing things under warranty. The most we've spent is $250. However, it has cost us a lot in time and inconvenience.”
Jerry L. Culver, Lroquois, S. Dak.: Jerry says his 1992 Case-TH 3900 cushion gang disk is neither his “best” nor “worst buy”. “It does a good, level job of disking. The cushion gang handles rocks easily. But when it was new the pins that hold the depth control hydraulic cylinder in place came off and the hydraulic fitting was sheared off the cylinder. The pins holding the ends of the cylinder only had holes big enough for small cotter pins, so I replaced all the pins with ones that had bigger holes in them. Also, the mulcher on the disk is a joke. Bolts are always falling out.”
Robert B. White, Chrisman, IIL: A 1994 Millermatic 130 wire welder and 1995 Henrob 2000 gas welder and cutting torch head Robert's “best buy” list. “The wire welder has been trouble-free. It does a fine job for the price. The cutting torch works as well as the company claims and is very versatile. “My two worst buys were a 1993 Century &5-amp wire feed welder and Vise Grip Quick Grip welding clamps. It didn't take much to throw the overload switch on the welder, so TE spent all my time waiting to work. The welding clamps do not grip lightly and easily slip off objects Pim trying to hold.” Gerald Krahn, Warroad, Minn... “The best buy Lever made was installing Marvin windows in the old larm house my son now lives in and in the new house we built five years ago. The insulated glass helps cut fuel bills. “My worst buy was a 12 1/2-hp Cenex lawn mower bought wo years ago. The trame is weak and twists on real uneven ground und then the belts slip. Also, the blades turn all the time even when disenpaged.” Alva L. Hayes, Salem, Ala.. Alva's “best buy” ts his DR trimmer/mower equipped with a 4 hp electric start engine. “It rolls through high weeds with case. ht uses heavy-duty nylon cord and cuts through the 416° FARM SHow O-2 st’ Buys iS page toughest weeds like butter.”
Jim Zinne, Ryegate, Mont.: “We bought a new Oliver 2255 tractor in 1974 and it gave us trouble every day of the nine years we owned it. have a list of 30 service calls and endless things I fixed on it. My dealer was helpful, but the tractor should have been replaced. I’ve talked to other owners who had similar stories. “My best buy is my 1993 Ford 250 diesel pickup equipped with a 4:10 rear axle and S-speed transmission. It's given me 38.000 miles of trouble-free service. Our 1989 Case-IH 7140 tractor is also a best buy.”
Gerald Austin, Salcha, Alaska: Gerald's unimpressed with his 1991 W-250 Dodge pickup equipped with Cummins diesel, “In 60,000 miles, I've had a front locking hub, transfer case seal, and re... «le seal go out. [thas less load carrying «pac ity than my old International pickup. The only good thing Lean say is that it gets fairly respectable fuel mileage, about 20 mpg uverage.” Clayton Severson, Stewartville, Minn, A Deere Gator 4-WD purchased a year ago is Clayton's “best buy”. “It's really handy around the farm, there's just no end to its usefulness. If I'm not using it, my wife is.” Daniel Rion, Prattsville, N.Y... “Our Badger Northland 3500 truck-mounted vacuum manure tink and pump is one of our best buys. It came ina kit that made it easy to install on our truck. It does a fine job and is easy to maintain,”
P.A. Lovejoy, Monongahela, Penn.: “I've had great luck with my 3-year-old Case-IH 11304-WD utility tractor. I've put 200 hours on it so far with no problems, T use it to mow around the house and barn, to pull a hay rake and a 6-ft. disk. The 4WD gives it enough power to get the job done. [also use it to push a lot of snow, I wouldn't hesitate to buy another one.”
Frank Allen, Kenton, Tenn.: Frank's more than pleased with the Chevrolet Silverado 4-WD pickup he bought new in 1993. It now has 30,000 miles. “It drives and rides like a Cadillac with plenty of head and shoulder room. Its 350 cu. in. engine is extremely powerful and gets better than 18 mpg, almost twice what my old Ford 4-WD pickup got. I'll never buy another Ford. “My worst buy was a Case-IH Magnum 7130 tractor equipped with front-wheel-assist. The hydraulics are a joke. The power lift leaks down while the tractor is in operation. You have to push the lift lever down and then pull it back up to reset it, It sometimes blows the hose end out of the outlets when lifting an implement. The engine had to be overhauled at 2,000 hours, It drives and rides like a log wagon compared to Deere tractors I’ve owned.”
David Nobbe, Barrington, Ill: “My worst buy is the Case-IH 8530 baler bought new last year. was replacing my 10-year-old New Holland 316 with the Case. In the 10 years I owned the New Holland I didn’t go through one bag of shear pins. I've used three bags of shear pins since I bought the Case. I spend as much time unplugging the baler and replacing shear pins as I do baling.”
Lyle Hoffman, Waterloo, Hl.: The 47in. Deere mower deck and grass vacuum Lyle bought for his 22-year-old Deere 110 mower gave “it new life. It mows much smoother and leaves a litter-free lawn, It's now up to specs of a modern mower. “With only 44,000 miles on my 1989 K1500 Chevrolet pickup, the bracket that holds the power steering, air conditioner compressor, and alternator cracked and broke off the studs in the engine block. That was last August. In October, we had to replace the transfer case because the old one was bone dry, even though we never noticed any oil leaks on our concrete driveway or garage floor. The used transfer case they put in operates smoothly, unlike the original. Cost on the second big repair job was $1,500 with no help from Chevrolet.”
Darrell Harvey, Brookeville, Ind.: “My best buy is an add-on step kit for TH 86 series tractors that improves the steps up to the cab and includes cylinder assist that opens the door of the cab farther. This kit (from K&M Mfg., Renville, Minn.) makes it as easy to enter and exit these tractors as newer models. “My worst buy is the Case-IH 656 hydro diesel I bought used, You have to use ether to start it, even on 90 degree days. Plus, parts are hard-to-come-by or non-existent.”
Jack Turner, Elkhart, Kan.: “My 1990 7140 Case-IH MFWD equipped with powershift transmission has a larger cab, quieter engine, less power hop under heavy load, and a smoother power shift, especially downshifting, than the Deere 4960's that I lease. At 5,000 hours it uses less oil than the 4960's at 500 hours.”
Arnold Ross, Webber, Kan.: “It has plenty of power and good fuel economy,” says Arnold about a 7110 Case-IH tractor, his best buy. “Ii has a comfortable cab that's dirt-free. Anc it’s easy to service.” A 1982 Allis-Chalmers 6080 tractor is Arnold's worst buy, “We've had it since 1985 and last fall the rear end went out. I had a hard time trying to find someone who could replace it. When finally did, the work was prived way too high for a used tractor, but went ahead and had it done because I really needed the tractor.”
Elmer Beiler, Paris, Tenn.; Elmer's “best buy” is his 1992 Case-IH 5130 Maxxum tractor. “We're well pleased with it. It has performed beyond our expectations. It handles great, runs cool, and has an outstanding 3-pt. hitch. The powershift transmission really shifts smooth, It’s built a lot better and heavier than anything built by competitors even though they all try to copy it. We'd recommend it to anyone. No problems at all after almost 2,000 hours of use. “We're also pleased with our 1991 Dodge W250 4-WD pickup equipped with a Cummins diesel engine. I'll pull almost anything we hook up to it. It’s easy on fuel and is a tough pickup that’s well suited for farm use. Starts easy in cold weather. It has 104,000 miles but still runs like new.”
Brad Becker, Alta Vista, Kan.: A 1994 Vermeer 604 Super J round baler rates as Brad's “best buy". “It’s a quiet, smooth running baler that makes a heavier bale than the 605F model that I traded in, I really like the ‘equal-fill’ electronic control system. It’s very dependable.” On the negative side, Brad lists his 1992 Case-IH 5140 front wheel drive Maxxum tractor, “Overall, I've been well pleased with it except for an electrical short in the powershift transmission that the dealer can’t seem to find. You almost need an electrical engineer to repair this tractor.”
Kevin & Rose Roll, Hays, Alberta: They rented an Alloway-Rau stubble shredder and like it a lot. “It works great on heavy stubble on our irrigated land, reducing the stubble to an easily incorporated mulch. It saves us at least three tillage passes every spring and makes it much easier to make border dikes for irrigation. “Our Case-IH 7200 grain drill, equipped with zero till openers, penetrates easily in heavy soil. It also clears heavy trash with ease, allowing us to no-till our irrigated land, “We bought our 1987 Hesston-Fiat 100-90 tractor about three years ago and have put 2,300 hours on it. We've had a lot of problems with it. We had to replace the clutch and have had problems with the electrical system and with gauges in the cab, Also, the front axle seals leak. The tractor does have a lot of power, is handy, and has a comfortable cab, But I'd never buy another one,”
Nelson Wedge, Earlville, N.Y.: Nelson nominates his 1993 Case-IH 5240 4-WD tractor as his “best buy”. “There are no words to describe the quality of this tractor. It has plenty of power, is easy to drive, and starts easy. The mechanical front wheel drive gets me through the worst conditions. It’s easy to change the oil and filters.”
Royce Kraft, Normal, Ill..: “My 1992 Case-IH 900 12-row, pull-type planter is my worst buy. As many as six rows come out of the ground as I go through the field, leaving corn planted too shallow to germinate properly. This planter has cost me $70,000 to $80,000 in lost production.”
Wayne Harter, Wakarusa, Ind.: A 1990 Case-IH 5130 tractor heads Wayne's “best buy” list. “It handles beautifully and is a dependable, economical tractor, We've put almost 3,000 hours on it. “My 1991 New Holland 553 skid steer loader’s been in the shop or repaired on my farm an average of every SO hours. It has less than 1,000 hours. The biggest problem is with leaky seals or O-rings. It costs $130 to $180 each time to repair. I like the Kubota diesel engine, but not the problems.”
David L. Shaub, Rolla, Mo.: “In 1965 we bought a 1949 L.A, Case tractor and we still use it to pull a disk and a 4-bottom plow. It’s our best buy of all time. “We like our 1993 Bobcat 7753 skid steer loader. It has a lot of stability and is easy on fuel, and the Kubota diesel engine always starts right up.”
Lawrence Jost, Garden City, Texas: Lawrence likes his Case-1H 7150 Magnum tractor. “It’s a good, reliable tractor that’s easy on fuel. A real work horse. All five of our Magnums have been reliable.” On the negative side, Lawrence lists his 1990 Ford F-250 pickup equipped with a 7.3-liter diesel engine. “It's a real lemon. No dealer could solve the problems we had with this truck.”
Ed Keyowski, Canora, Sask.: “Works great in all crops,” says Ed about his 1992 Case-IH 1680 axial flow combine equipped with a specialty rotor and 30-ft. straight-cut header, “No downtime in 6,000 acres, Ithad a few small electrical problems which the dealer handled promptly.” “Tt had a few small electrical problems which the dealer handled promptly.”
Jim Kehoe, Lansdowne, Ontario: “My 1993 Fiat 100-90 tractor is easy on fuel and has a quiet cab with convenient controls, It has a lot of power but could use more gears between 4 and 7 mph. “My 1992 Case-IH 8545 baler is a best buy. The bale thrower couldn’t work better. Capacity, bale shape, tying, etc., are excellent.”
Craig A. Fleishman, Minburn, Iowa: “My 1992 Case-IH 9006-row, 30-in. planter equipped with a ridge-till attachment is my best buy. Itcan be used in minimum-till, notll, or ridge-till conditions without modification. The ridge-till attachment does a superb job of cleaning the ridge.”
Gerald Grant, Nevada, Iowa: Gerald’s impressed with his 1991 Deere 875 12-row, 30-in. high residue row crop cultivator. “It’s well built and can handle a lot of trash and stays in the ground regardless of how hard the ground is. We're pretty much Case-IH customers. We bought this cultivator because our local Case-IH dealer couldn't get acultivator that we had ordered seven months earlier and we needed it. We couldn't be happier with it. “Sears Craftsman electric-powered shop tools have lost some of their quality. For example, on drills the chucks slip and won’t hold bits, switches fail, and the motors burn out. We’ve started buying Makita electric hand tools.”
Don Bromley, Brandon, Manitoba: “It has a lot of power and is easy on fuel,” says Don, pleased with his 1990 Case-IH 2096 tractor. “The cab is quiet and has good visibility, and the steering is light and responsive, “My 1989 Ford F-800 truck equipped with a 429 cu, in, gas engine is my worst buy. The engine is hard on fuel and lacks power, and it’s hard to shift into second gear. After I spent two years complaining to Ford, their last words were, ‘It’s the nature of the beast so live with it.’”
Lawrence Erlenbusch, Angela, Mont.: “My Deere 95 combine, which I bought used, is my best buy because it’s casy to service and operate. However, it’s turning into my worst buy because Deere no longer makes parts for it.” James E, Duermeier, Pulaski, Tenn.: “Thirteen years ago! boughtan Echo452VL 16-in. chain saw. It has been a real workhorse. It even survived being run over by a bulldozer. The only parts (other than chains) that have had to be replaced were a plastic gas line and a gas filter. “T'm also impressed with my CattlePro beef cattle records, management and performance analysis software (Bowman Farm Systems, Inc., Rt. 5, Box 25, Cynthiana, Kent. 41031). It’sa great way for beef cattle producers to keep comprehensive records. The computer program is casy to use and covers every type of record that a cowman needs for a successful operation, such as weights and measures, herd inventories, sires, dams, progeny, cow doctoring, pelvic measurements, etc. You decide what records to keep. The bottom line is that Cattle Pro can track a snake across a flat rock. I really like it.” Lloyd Rosborough, Harvey Station, N.B.: “My worst buy is a Case-IH 485 tractor. It has 1,600 hours on it. I’ve installed two new clutches.”
Lee Downing, Beaverdam, Va.: Lee's happy with his Vicon 510 16-ft. tedder. “It does an excellent job of fluffing hay, even alfalfa, and is easy to fold up for transport. “My Vicon 321 10 1/2-ft. disc mowerconditioner is an amazing machine. It'll cut anything and can operate it as fast as I want. I cut about 10 acres per hour and not all of my fields are large. I'll never buy another brand.” “My Case-IH 3450 round baler is a worst buy but not because it has mechanical problems. I’ve made more than 1,000 bales with it and never had a minute of trouble. The problem is that it makes a 4-ft. wide, 5-ft. long soft center bale and after the soft center has been formed, it doesn’t wrap cnough hay around it to hold the bale together very well, It might work alright if the entire bale was wrapped with plastic.”
John Tibben, Kincardine, Ontario: John’s the satisfied owner of a 1993 Cheyrolet 3/4-ton 4-WD pickup equipped with a 6.5-liter turbocharged diesel engine. “It has lots of power and gets excellent mileage on long trips - about 25 mpg on the highway and 20 to 21 mpg around town, It rides like a car and is nice and quiet. Starts right up even in the coldest weather. “My 1989 Kubota M6950 DT tractor isn’t really a worst buy because it does everything we want it to and starts good in winter. However, parts for it are expensive. For example, a simple work light switch sells for $73. Another problem is that it’s hard to service. You need the fingers of a newborn baby to work in some of the cramped spaces. “My Deere 530 and 535 round balers have both been best buys. I made 15,000 bales with the 530 before I traded itin for the 535 and I made 17,000 bales with it before trading for a new 535 equipped with net wrap. We'll see how well the new one works. Ido some custom baling and a lot of people ask for these balers. They make tight bales that do a good job of shedding water. Net wrap should help even more.” James Greer, Gorrie, Ontario; James's 1992 Case-IH 8520 in-line square baler heads his “best buy” list. “I've used it to make over 40,000 bales with little downtime. It can make up to 400 bales per hour with minimum leaf loss because it has a low pickup height and because hay doesn’t get handled as much before being tied because there's no cross auger. It makes firm, square bales that truckers really like, “Two years ago I bought a Harco 45-ft. bale elevator. It’s well-built and should last a long time. My only complaint is that it’s too heavy to be easily moved around. To solve the problem I had a friend mount a wheel under the front of it.”
Leo Mugan, Mitchell, Wis.: “My Deere 6400 tractor equipped with a cab and power quad transmission is my best buy. It’s the neatest, handiest, most comfortable tractor I've ever owned with some real improvements over older models, including the ability to be refueled from the ground, an improved transmission, and a smokeless, gutsy engine.” Floyd Hartke, Dieterich, HL; “I bought my best buy 1987 Case-IH 4694 tractor used with 800 hours on it. After 1 put on about 200 hours, a tooth chipped off the timing gear. Even though I bought it used, the company still paid for most of the repair.”
Ray Fiedler, St. Joseph, Minn.: Ray's impressed with his 1993 Ford 8630 2-WD tractor. “I really like the powershift transmission, foot throttle, and cab. It has doors on both sides. “My 1992 Case-IH 600 silage blower runs smooth and has a lot of capacity. use it with a 100 plus hp tractor.” On the negative side, Ray lists his Deere 1219 mower conditioner. “I bought it in the fall of 1992 when I traded in an 8-year-old New Holland 489 haybine and used it for the first time in 1993. didn’t like the way itcut - hay plugged up at the sickle guards.”
Jay Volk, Arlington, Neb.: “T’ve worked this tuck like a tractor but it still rides like acar,” reports Jay, impressed with his 1978 Dodge extended cab 4-WD pickup. “We “I've worked this truck like a tractor but it still rides like a car.” blew out the engine hauling hay so I overhauled it, as well as the transmission and transfer case. I wouldn't trade it for a new one.”
Stanley Greathouse, Johnsonville, Ill.: “My best buy is my 1994 Lincoln Town Car, I’ve also owned 1992, 1990, and 1986 models. All of them were comfortable, trouble-free, and fuel efficient. “My Case-IH 3594 tractor equipped with front wheel assist is a best buy. It has a lot of power and has been trouble-free.”
Richard Arsnman, Payson, HL: “I'm well-satisfied with my 1992 Case-IH 7120 tractor equipped with front wheel assist. It has a lot of power and traction, a quict cab, convenient controls, and an 18-speed powershift transmission that makes ita pleasure to operate. “T like my 1991 Deere 9500 combine with rear wheel assist. It walks right through soft fields where others would bog down and has the power and capacity to handle high yielding crops fast and efficiently. It can be adjusted to save more grain than any other combine I’ve ever used.”
Don W. Langmaid, Newton, Iowa: “It does a good job and is easy to service,” says Don about his 1990 Case-[H 1460 combine. “Luse a 20-ft, grain head and a 6-row, 30-in. corn head with it.”
Garry Stewert, Hanna, Alberta: Garry likes his Massey Ferguson 8460 combine equipped with a rake-type pickup and straight cut header. “It worked well for us last year in heavy, wet crops. We pul more than 200 hours on it. We had some problems with the electric solenoid that’s used to start and stop the header. “T like my Flexi Coil System 65 sprayer equipped with wind screens. No problems. “My 1992 Case-IH 8460 baler is a worst buy. When it worked it made nice bales, but the slip clutch had to be rebuilt five or six times in two years. An upgrade kit didn’t make much difference. also had problems with rollers that came off and got bent. “The slip clutch had to be rebuilt five or six times in two years.” Another problem is that leaves and chaff build up on the knife so that it won't cut the twine. I have to get out and hand cut the twine and clean off the knife.”
Sunny Brook Farms, Ava, Ill..: “Our Hardy outside wood-buming furnace is a best buy. It heats 8 rooms and 2 baths in our house with a very even heat. All smoke, ashes, and wood trash stay out of the house. It fires only twice a day in cold weather and once a day in warmer weather. I use junk mail, feed sacks, boxes, and trash around the farm as fuel in the summer to heat hot water. “Our 1993 Case-IH 1250 feed grinder is a worst buy. It was delivered withoutall the parts we ordered. The dealer took it back last December and as of early February they still hadn't returned it. Six weeks should be long enough to get parts from the company. They have our money, but all we have is a piece of paper.”
Lester Gehman, Manheim, Penn.: “My 1989 Dodge diesel pickup is my best buy. The Cummins diesel engine starts easy, runs like a top, and pulls like an 8-horse team. It gets 20 to 22 mpg. Takes only half as long to fill the fuel tank as the Ford we owned before.” Norman Farrington, Mechanicsville, Iowa: Norman nominates his 1991 New Idea 5209 rotary hay mower as “best buy”. “All I do is get on and go. It does a great job at fast speeds. “My 1988 Case-IH 7120 tractor handles comfortably, has a quiet cab, and is easy to service. The powershift transmission performs well. “My 1992 Deere 535 round baler with net wrap is built strong to withstand damage on rough ground and makes good bales at high speeds. The netting speeds up baling and sheds water. Works great as long as it goes on right. However, I’ve had problems with it catching and tearing.”
Jim Hrdy, El Reno, Okla.: Jim's had good luck with his 1988 Case-IH 7140 tractor. “T put over 1,000 hours on it every “This tractor stands up to use by high school and college kids who work for me during the summer. It's greenhorn driver tough.” year. It had some minor electrical problems but the dealer solved them. This tractor stands up to use by high school and college kids who work for me during the summer. It's greenhorn driver tough. “Tlike my 1984 International 1950 truck equipped with an 18-ft. bed and hoist. It’s powered by a 6-cyl. diesel engine and has 120,000 miles, It's the most dependable truck on the market in my opinion, I also have Chevrolet and Ford trucks but they can’t match this truck’s performance. I'ma custom harvester and use this truck to pull a Case-IH 1680 combine from Oklahoma to South Dakota, I never have to stop. I’m well pleased with its durability.” Jim says he had bad luck with his 1989 Deere 1508 mower from the start. “It’s the only mower I've ever owned where I had to mow everything twice in order to get a good cut, even with sharp new blades. I had to constantly replace U-joints on the main driveline. The dealer stood behind the mower until the warranty ran out and then it was mine. After about 4 years of putting up with it, traded it off for a Deere 1518 mower. It works good. No problems.”
Bill Knoff, Nahotah, Wis.: A 1991 GM dually pickup equipped with an extended cab and 454 cu. in. engine rates as Bill's “best buy”. “I convert all my 454’s to dual fuel LP and gas. One set of spark plugs lasted 88,000 miles. change the oil every 20,000 miles. This 1991 model is a super truck. I putan aluminum flatbed on it which draws a lot of attention. “My Case-IH Magnum 7140 tractor equipped with front wheel assist has excellent comfort, good visibility, and is easy to ( ( service. It gives Deere a good run for its money because it’s a good tractor that’s reasonably priced.”
Myron Schafer, LaCrosse, Ind.: “Our 1993 Case-IH 1666 combine is a best buy. Ithas more power than the 1660 model that itreplaced. The specialty rotor does a great job in tough-stemmed beans. The unloading auger wobbles but the dealer says he'll replace it. We installed a Schumacher ‘easy cut’ sickle on the 1020 head (S.I. Distributing, St. Marys, Ohio). The sickle has worked well so far. We hope it continues to work better than Case-IH’s 1 1/2-in, system. “Our Hesston 560 round baler is a best buy. It would make perfect bales every time if] always drove according to the monitor's directions. We had some problems with the hydraulic cylinders, but the dealer promptly took care of them. “Our 1977 WilRich 30-ft. field cultivator is a best buy. We haven't had to do anything to it other than regular maintenance. We'll buy from Wilrich again. “Our 1990 Boman Bale Master 6810 round bale carrier from American Geothermal isa worst buy. Welds on the center main frame keep breaking. It’s designed for 8 bales but is built to handle only half that. 1 called the company three times tocomplain. Their only reply was, “That’s never happened before’. Buyer beware.”
Robert J. Gardner, Chester, Md.: Robert’s happy with his 1992 Case-IH Magnum 7140 tractor equipped with front wheel assist. “It has plenty of power, is easy on fuel, handles comfortably, and looks great. It’s such a good tractor other companies are copying it.”
Robert E. Pustolka, Ballston Spa, N.Y.: “It has performed beyond my expectations and is a best buy,” says Robert about his Diller self-locking feed wagon (Diller Equipment Co., 2325 St. Thomas, Edenville Road, Chambersburg, Penn, 17201 ph 717 369-2691). “It accommodates 24 head of cattle and is safe and fool-proof. Works better than any other feed wagon on the market and does the work of two hired hands. The manufacturer thought of everything. My only regret is that I didn’t buy it when it first came out. I use it for breeding, pregnancy checks, veterinarian work, feeding, elc. On the “worst buy” side, Robert's disappointed with his leased 1993 Case-TH round baler, “It works slow and makes soft bales that are hard to start and hard to eject. The bales have tremendous spoilage. I wouldn’t consider leasing another one, let alone buying one.”
Donald Olayer, Beaver Falls, Penn.: Donald nominates his 1993 Case-IH 8350 centerline baler as his “best buy”. “Il ordered the baler with a hydraulic pickup and bale tension adjustment. It makes solid, uniform bales and doesn’ tlose as many leaves as my old baler. I like the fact that it follows right behind my tractor on the highway. I haven't had any problems with hay getting caught on the drawbar due to driving over the windrow.” “T leased a 1994 Ford Explorer and really like it. It's a pleasure to drive and is fuel efficient. I like the push button 4-WD.”
Delbert Bauersachs, Pinckneyville, Ill.: “T’'m well satisfied with my 1992 Case-IH 7150 tractor. It has 790 hours on it with no problems. It’s easy to handle and the powershift transmission works great. It's fuel efficient and, with well over 215 hp, it'll outperform my Case 2670 in the field, I use itto pull my 1992 Case-TH 496 32-ft. disk in 9th or 10th gear. The disk does a good job leveling and is also a best buy. I also use it to pull my Great Plains 20-ft. no-till drill at 9 to 10 mph. The drill does a super job. planted 6,000 acres with it and had to replace only one press wheel bearing. “I sold my Deere 7000 8-row, 30-in. planter and bought a Kinze 8-row, 30-in. planter. It’s a best buy. The Deere planter was built too light and bearings were always going out. It went through over 25 bearings in three years. The Kinze planter is built heavier so I haven't had any bearing problems in three years. My only complaint is that it doesn’t plant as evenly as the Deere planter. “My 1987 Case-TH 2294 tractor has 2,450 hours with no major problems. And I think my 1991 New Holland TR96 combine is the best combine on the market. It shells up to 1,900 bu. of corn per hour.”
Louis Kludy, Shelby, Mich.: “My 1991 Case-IH Maxxum 5120 2-WD tractor has plenty of power and is easy to operate. It has 1,000 hours but has never been back to the dealer, The cab is quiet and comfortable.”
Mark Knudsen, Jesup, Iowa: “My 1992 Knight 7716 slinger spreader is my best buy. It handles a wide variety of manure, from slop to pen-packed, with flying colors. However, it does unload slow when spreading pen-packed manure, “We use our 1993 Yamaha 350 4-wheel ATV fora lotof jobs around the farmas well as for fun. It has never been back to the dealer. “My 1986 Case-IH 1660 combine is also a best buy.” On the “worst buy” side, Mark’s disappointed with his 1993 Yetter 2967 row cleaners. “They're supposed to work in conjunction with the no-till coulters on my Deere 7200 12-row planter. They're designed to bolt on top of the casting for the no-till coulter. However, the surface on the casting is tapered and not flat so the row cleaner brackets don’ tsitsquare. Thismakes it almost impossible to get the row cleaner wheels centered with the coulters and puts a bind on the pins used to adjust them. The rowcleaners were in short supply last spring sol bought them sight unseen. I won’tmake that mistake again.”
Geston Womack, Cedartown, Ga.: “My 1991 Case-IH 2044 cotton picker is my worst buy. It had 425 hours on it when the transmission failed. The company paid for half the repair bill, but it still cost me over $4,000. Last year at 699 hours the hydraulics failed, costing me another $4,000 and 8 days of downtime. In between these major failures the steering cylinder failed twice, resulting in a complete loss of steering. There also have been a lot of other problems. It’s the mostunreliable piece of equipment I've ever owned.”
Bob McComb, Castleton, Ontario: Bob’s the owner of a 1991 Ford F-150 4WD pickup. “I'm generally satisfied with it, but there seems to be a problem with the auto-hubs or transfer case. Both were replaced under partial warranty.”
Weeks Bros., Swan Valley, Idaho: “Our best buy of all time is our 1973 International 1066 Hydro tractor equipped with front wheel assist. It has 10,300 hours on it and except for a 3-month period two years ago when a valve stuck in the hydrostatic transmission, we’ ve used it 350 daysa year. It was overhauled at 5,875 hours and has had two complete overhauls of the injector pump. We’ve also had some trouble with the transfer case for the front wheel assist. We use it mainly in the winter to feed cattle. It’s on its fifth set of rear tires and sixth set of front tires.”
Richard Schlaefli, Mankato, Kan.: Richard's satisfied with his 1992 Case-IH no-till air planter equipped with Acra Plant Trash Whippers. “No-till lets me make fewer trips through the field and saves time, fuel, and wear and tear on machinery. I like having to fill only one hopper. It’s simple to operate and easy to maintain.” Richard S. Gerhard, Quakertown, Penn.: “My worst buy ever was a Troy-Bilt 26-in. rototiller. It was poorly welded together and the transmission case was equipped with ano. 40 chain which was like a bicycle chain. It was always tearing or jumping off the cog wheel, and it took about a day to repair because the transmission case had about 40 bolts in it. I wanted the company to install a no. 50 chain but they refused so I bought a Wheel Horse rototiller. It has gears and a no. 60 chain. Works great.”
Herman Fentress, Crofton, Kty.: “I think my New Idea 5209 disc mower is the best disc mower on the market, I have two of them. I’ve owned other brands, but none are as easy to maintain as this one. I’ve waited 2 to 3 days for cutterbar repairs on other brands, but even in the worst case my New Idea model can be repaired by anyone in a short time right in the field.”
Paul DeClerco, Champion, Alberta: “My 1990 GM 15004-WDpickupequipped with a 5-speed manual transmission is my worst buy. All the seals leaked on the front differential and they went out on the rear axle. The transfer case wouldn’t shift, the engine bumed oil, the clutch had to be replaced, headlight wiring failed, and the air conditioner leaks water in the cab. All of these problems happened before iteven had 50,000 miles.”
Tom Wencl, Blooming Prairie, Minn.: Tom nominates a 1989 Geh133 10 skid steer loader as his “best buy”. “We tested both Case and Bobcat before we bought Gehl. We prefer its ease of handling, power, and ROPS guard. “We also like our 1983 International 4000 windrower which we bought used. The 12-ft, double auger head is trouble-free and works well in oats and hay, The crimper has one steel roller and one rubber roller which works better than our previous win drower that had two rubber rollers. It has good power. However, I wish it had a variable speed reel so we could go faster in short hay.”
Jeff Knupp, Dysart, Iowa: “We used it to plant all of our soybeans with excellent results,” says Jeff, pleased with his Great Plains 15-ft. no-till drill equipped with a self-locking coulter caddy. “We mounted an old International seed flow monitor on the drill and spaced four sensors among the 22 seed drops. It’s good insurance in case the drill malfunctions or runs out of seed.”
Ted Ross, Forest, La: Ted's ‘worst buy” ishis 1989 Ford F-250 3/4-ton4-WD pickup equipped with a diesel engine. “The speedometer went out at under 12,000 miles and was repaired by a dealer, It wasn’t long before it went out again. I was told by another dealer's mechanic that the speedometer had an engineering defect, Two rear wheel seals also went out. The transfer case was removed and repaired twice (at under 12,000 miles), the fuel gauges failed, and the seat belt has never retracted properly. The 5-speed manual transmission became very hard to shift and cost $886 to repair. The transmission repair happened well within the 60,000 mile, 6-year power train warranty, but the company wouldn't cover it because the speedometer had failed and showed the incorrect mileage. The company refused to pay for the transmission repair even though other Ford dealerships had failed to repair the speedometer. “Perhaps U.S. truck makers will improve the quality of their trucks when Nissan, Mazda, etc., build comparable sized trucks for sale in this country. However, despite the shoddy workmanship and the company’s failure to honor the warranty, this is a ( ( powerful, rugged farm truck.”
Jim Hermanski, Enid, Okla.: A Same tractor and mower heads Jim’s “worst buy” list. “It's hard to change oil on the tractor without getting oil all over the side of the engine. The pto brake is a real hassle to operate and it’s hard to hook up equipment, “The mower’s automatic wing locks are a pain, and there should be a way to get hold of the speed joint and unhook it without smashing your fingers, The hydraulic cylinders on the wings leak down.” Jim's happy with his 1985 Deere 4450 mfwd tractor. “It’s dependable and has good visibility and case of operation. Because of the mechanical front wheel drive I don’t need to use wheel brakes in the field. The power shift works great for operating a baler. “My Deere 1508 mower also is a best buy. The blades are easy to change and are tough.”
Glen Peterson, Marshfield, Wis.: Glen's the happy owner of a 1989 Ford 7710 4WD tractor, “It was reasonably priced compared to other brands, I’m very pleased with its power, maneuverablity, and case of handling. Most service points are very accessable,”
Virden Smith, Findlay, Ohio: Virden’s had trouble with his 1986 Deutz DX 110 tractor. “The clutch went out at 1,000 hours and the hydraulic valves had problems. The brakes had to be rebuilt. The transmission bearing failed and wiped out a ring and pinion as well as a differential case and bull gear. I had owned a Deutz 9006 for nine years with no problems, “My 1989 Ford Tempo has 14,000 miles and hasn't been back to the dealer once.” Eugene Bissey, Dwight, Ill..; “My 1990 Toro 21-in, recycler mower is a worst buy. The bagger door wouldn't stay open but the dealer fixed it. Then after about 14 hours of use the door cracked. The rear wheel drive is very unhandy. Poor quality forthe money. “My 1989 Ford Ranger XLT Super Cab pickup is a best buy, Handles great in all weather, rides good and starts great.”
Jerry Newton, Anderson, Alabama: Jerry likes his 1977 International 1086 tractor. “It has plenty of power, is easy on fuel, and has had very few repairs. It's areal pleasure to drive.” On the “worst buy” side is an 8-ft. Rhino rear-mounted scraper blade. “The dealer had to order the blade and it took three months to getithere, When itcame it was so scratched up that it looked more like a used blade than a new one. asked the dealer if he could get some touch-up paint. He said he couldn't. I saw a Rhino representative al a farm show so I told him about my problem. He said I'd have to buy a whole case of paint just to getone can. This will be my last piece of Rhino equipment.”
Philip Long, Bethany, Mo.: Philip says his 1984 Deutz-Fahr DX 160 tractor equipped with a powered front axle is both a “best” and “worst” buy. “I use it to pull a 25-ft. disk and 26-ft. field cultivator. It’s a pleasure to operate, rides well, has a good cab, and excellent air conditioning and heater, It uses just 6 to 6 1/2 gallons per hour and the gear selection is unequaled by any other tractor brand except White. However, an ‘O’ ring in the engine oil pump blew out at 450 hours and kept me from using the tractor for 4 weeks. At 1,690 hours it started jumping out of gear. I also had to replace a ring and pinion, transmission shaft and numerous other parts totaling $5,600. The company paid about $1,200 of that. The ring gear case was replaced by a bigger, heavier, and hopefully better part. I also had to replace two sets of gear shifter rails at $750. The tractor now has 2,200 hours and it’s starting to shift rough again. “On the positive side owna 1975 White 2-105 tractor with over 6,000 hours. The only repairs were a set of rings, a set of sleeves and pistons, two fuel injection pump repairs, and an Eagle air conditioner kit to replace the factory one. The 3-speed power shift, transmission, and rear end have never been touched.”
Dale Stevens, Skaneateles, N.Y.: Dale is the unhappy owner of a 1984 International 6388 2 plus 2 tractor, “The pto assembly broke four times in four years and had to be replaced each time, The company tried blaming the problem on our implements, but it was foolish on their behalf because a 130 hp wactor should handle a 200 bu. spreader or a 2-row chopper. If it can’t, there’s something wrong. Our dealer tried hard to help us out. Finally Case-IH sentout a factory rep who found thata factory defect in a casing had caused the problem. Now hope Case-IH has the courtesy to return the thousands of dollars that we needlessly spent.”
Douglar Grant Jr., Rupert, Idaho: “My _ 1987 Deere 8650 tractor is a sweetheart, I’ve used it only about 300 hours but the cab, controls, and seat are better than those on Case-IH tractors.”
Allen Beruening, Elizabeth, Ill.: A 1987 Case-IH 3394 tractorrates as Allen’s “worst buy”. “The park lever doesn’t work right. One time the lever let loose and put the tractor in gear. It went right through our shed where my wife and granddaughter had been standing only seconds before. The dealer tried to repair it several times without success. We’ ve been fighting with them the whole while but they refuse to do anything.”
Craig Eppert, Madrid, Iowa: A 1988 Case-I1H model 4800 25 1/2-ft. field cultivator is Craig’s “best buy”. “The leveling hitch keeps the cultivator level front to back. Also it has great trash clearance.” “My worst buy is a pair of Goodall crop dividers which I bought last fall for my IH 810 floating grain head. The brackets didn’t bolt right on the head. The dividers do a poor job of keeping bean plants from dragging on the ends of the cutterbar,”
Alan McRae, Goodyear, Arizona: “Tt offers unequalled pulling power, great fucl efficiency, and a comfortable cab,” says Alan, happy owner ofa 1989 Case-IH 7120 Magnum front-wheel drive tractor. “With the 5,000 hour warranty this tractor can't be beat.” Alan’s “worst buy” is his 1985 Ford F150 pickup. “It’s a total piece of junk. I’ve never seen a piece of machinery with so many broken parts. I'll never try a Ford pickup again unless they dramatically change it.”
Robert Arneson, Tallulah, La.: Robert has had lots of trouble with Case tractors. “We own three Case 2870 4-WDs and one Case 26704-WD. None of these tractors has more than 3,200 hours, but we've overhauled practically every nut and bolt on them. They have weak front and rear ends, jerky powershift transmissions, and leaky planetary gear drives. Fuel injectors on the 2870's can’t be overhauled because the valve material is too soft. One of the 2870s has more hours in the shop than in the field. It was shipped from the factory with the wrong plumbing so that unfiltered oil went directly to the transmission. Another tractor came from the factory with 45° valves and 30° valve seats which caused the valve heads to pop off and of course they dropped = linate suys directly on top of the piston. We bought Case tractors because our dad was a Case dealer. Never again. Our next tractor will be a Versatile 975 tractor equipped with a standard transmission. Never again will I purchase a tractor with a powershift transmission unless it’s an Allison powershift. Farmers in this country are getting sick and tired of making the parts departments rich.”
Roger Antoniuk, Bonnyville, Alberta: Roger's “worst buy” is his 1987 Case-IH 39-ft. chisel plow. “It doesn’t pull straight or level and plugs up too easy. They should make it with five rows of shanks instead of 3 1/2 rows.”
Jack Grosnick, Moose Jaw, Sask.: “My 1987 Versatile 256 tractor is truly versatile, trouble-free, and economical to operate. The controls and seat are reversible so you can mount equipment on both ends and operate it with case. It works beautifully on mowers and balers.”
Thomas Bueter, Ansonia, Ohio: Thomas likes his 1987 Case-IH 1680 combine. “We purchased it with a special rotor that lets us combine soybeans in tough conditions so we can start earlier on dewey mornings and run later in the evenings. We've now installed the rotor in our IH 1480, Keep up the good work, Case-IH.”
Mark Ries, Goodwin, S. Dak.: “My best buy is my 1988 New Idea 3622 manure spreader. Manure doesn’t freeze to it even in -30° below temperatures, Manure in my Case-IH 540 manure spreader sometimes froze up to 6 in, thick,”
Robert Alexander, Edam, Sask.: Robert likes his 1988 Case-IH 7120 Magnum 2WD, 150 hp tractor. “I put 500 hours on itin one year. Ithas many excellent features, but the powershift transmission really stands out. It shifts exceptionally smooth and really shines with pull-type combines.”
Jerry Solyma, Meadow Lake, Sask.: "These Case tractors are total junk," says Jerry, unhappy owner of a 1981 Case 2390 tractor and 1982 Case 1490, “The 2390 engine blew up at 849 hours, It was under partial warranty thanks to a good dealer. The 1490 has had one problem after another with the water pump, cab blower motor, and power steering hoses. The front axle bushings and bearings have been repaired twice. dackitiaaum 255 In 1,746 hours I've replaced three hydraulic pumps at a cost of $630.”
Gerald Smith, Marienthal, Kan.: “My worst buy is my Case-IH 2594 tractor, At 472 hours the shift fork wore out because there were overbeveled gears in the transmission. Case-IH issued a modification order to repair the transmission, but they won’t warranty the transmission repair.”
Raymond Rumford, Ottawa, Kan.: A 1988 Case-IH 885 tractor equipped with mechanical front wheel drive and a 2255 front-end loader is Raymond's “best buy”. “This tractor has lots of lugging power, is economical on fuel and a pleasure to drive. It’s small enough to fit into tight places such as my shed, yet it does the work of a big tractor. The front wheel drive is excellent for loader work.”
Ron Hanmer, Govan, Sask.: Ron's pleased with his 1988 MacDon 36-ft. combine header (MacDon Industries, Winnipeg, Canada). “We mounted it on our Case-IH 1680 combine and it performed perfectly on a crop too short to swath. We harvested 2,000 acres at 5 to 7 in, off the ground and broke only two knife sections.”
Larry Short, Rochester, Texas: “My 1989 Case-IH 7140 MFD tractor is the finest tractor I’ ve ever operated. Deere has some very formidable competition. It's about time.”
Hardies & Sons, Hillman, Mich.: “Our Case-1H 4600 Vibra Shank field cultivator pulls smooth and straight and rarely plugs up. It works good for minimum till and finishing work.”
Michael Comstock, Kenton, Ohio: “A 1986 Ford F-350 Dually 4-WD 6.9 diesel pickup heads Michael's “worst buy” list. “This pickup is a piece of junk! The master cylinder completely broke off the firewall three times, and the front end shimmies so bad the truck goes all over the road. We had it in two different shops on three different occasions, replacing two sets of shocks and Stabilizer bars and other steering parts, as well as three sets of Goodyear Wrangler radial tires. We also replaced three light switches, one transfer case, three speedometers, three oil pressure sending units, one glow plug unit, one slave cylinder, one master cylinder, one clutch, three sets of brakes, and one set of emergency brakes. Last year we spent more than $3,000 on repairs, not including the cost of the tires. The warranty seems to cover all parts except those that break. The diesel engine pulls great in low range but has no power at higher speeds - you need a mile and a half of clear highway to pass someone. And if you're driving into a head wind, forget it.” Michael’s “best buy” is his 1976 GMC Sierra Grande 25 3/4-ton 4-WD pickup equipped with a 400 cu. in. engine. “This truck has taken severe abuse but caused us few problems, Without a doubt, it’s the best truck we've ever owned. It’s now semi1inate sUYyS retired and is basically a show truck, but we still use it on the farm whenever necessary." Ivan Bruder, Sauk Centre, Minn.; “My 1970 Chevrolet 3/4-ton pickup up has 476,460 miles and should easily reacha half million miles,” says Ivan, who notes thatthe pickup is now on its fifth set of tires, It’s equipped with a 350 V-8 engine and automatic transmission. “When hauling grain I load the pickup and pull two gravity boxes. I change oil every 1,500 to 2,000 miles and it’s paid off because the original engine went 187,000 miles and the present engine went 285,000 miles before it needed a valve job and rings. The engine still maintains normal oil pressure but it does use a lot of gas, getting only 12 to 13 mpg when it’s empty.” .
Richard Neal, Fillmore, N.Y.:“I'llnever buy another tractor from Case-IH,” says Richard, disappointed with his 1984 International 784 4-WD tractor. “It has only 1,800 hours but we had to rebuild the engine twice and install a new, shorter 2X injector pump. We also had to rebuild the rear end and it’s a hard starter below -30°.”
Bobby Skipper, Cochran, Ga.: Bobby's happy with his 1988 Case-IH Magnum 7110 tractor. “It has much more power than I expected and the fuel economy is unbelievably good for a tractor with this much “It has much more power than I expected and the fuel economy is unbelievably good for a tractor with this much power.” power, It handles well and cost somewhat less than a comparable size tractor of another well known brand.”
Glen Kesteloot, Marshall, Minn.: Glen's pleased with his 1988 Case-IH 9170 4-WD tractor, “The cab is comfortable and offers a good view on all sides, and the lights are as bright as daylight. It has a Cummins engine with powershift transmission and a decelerator pedal which lets me slow down as I turn on the ends of fields.”
Robert Kallenbach, Bolivar, Mo.: Robert's “best buy” is his 1988 Delmhorst DHM.-1 baler-mounted hay moisture tester. “It provides accurate moisture readings on-the-go so I don’t have to get off the tractor and probe each bale.” Howard Churchill, Harrietsville, Ontario: “The fuel economy is incredible and the powershift transmission makes ita pleasure to drive,” says Howard, pleased with his 1988 Case-IH 7120 Magnum FWD tractor. “It has plenty of power and great operator comfort and visibility. The fiveyear, 5,000 hour warranty is a big comfort, too.”
Roy Milne, Cutknife, Sask.: Roy is disappointed with his 1988 Case-IH 5600 39-ft. cultivator, “It wouldn't stay level so the company changed the main pivot arm and lift cylinders. It plugs fairly easily and pulls crooked when the outside wings catch grass on the edge of the field, Also, it had six flat tires on the first 500 acres.”
Eugene Patenaude, Perigord, Sask.: Eugene’s “worst buy” is his 1988 Case-IH 5000 Vibra chisel. “The main frame wasn’t completely welded and one axle was ruined after two weeks. It sidetracks and doesn’t penetrate properly, Another problem is that it was equipped with three different makes and sizes of tires.”
W.G. Thompson, Jewell, Kan.: “My 1987 Case-IH 2394 tractor has plenty of power for its size, handles well and is equipped with a good air conditioner and cab.” On the negative side, “It’s hard to service and change belts on my 44-in. cut Grasshopper lawn mower.”
Gilbert Weber, Crookston, Minn.: Gilbert didn’t like his 1985 International chisel plow, a 31-ft, model with folding wings, so he traded it in for a new Case-IH model which he’s satisfied with. “The wings’ frames wouldn't hold together so we had them welded and reinforced twice. The company offered to replace the wings but we traded instead.”
Roger Radloff, Oshkosh, Wis.: “My 1986 Deere AMT 600 5-wheeler is handy, trouble-free and gets good mileage. I built a front towing bar on it so I can pull it to the field behind my tractor and implement. At milking time, drive the AMT home, leaving the tractor and implement in the field, We also use it to pick up rocks .” Arthur Mangels, Polson, Mont.; Arthur is pleased with his “best buy” Case-IH 445 baler. “Itproduces much more uniform bales than Deere or New Holland balers, and doesn’t cut a short chunk of plastic twine and leave it lying on the hay as some brands do. However, this baler should have a heavier gearbox and driveline.” Arthur says his “worst buy” is his 1985 Deere 2550 tractor equipped with MFWD. “The hydraulic system leaks and the Deere 245 QuickTach front-end loader doesn’t have enough lifting capacity. Also, loader mounting brackets in front of the windows interfere with visibility for row crop work.”
Greg Vanhie, London, Ontario: Greg nominates his 1988 Case-IH 5100 Soy Special 21-run double disc seed drill, equipped with depth gauge press wheels, as his “best buy”. “It accurately meters seed and delivers good down pressure on each run. The depth gauge press wheels are probably the best in the industry and accurately control seeding depth. However, the acre counter doesn’t work right because of a poor linkage setup, and the clevis-style drawbar hitch is far too sloppy. We altered the clevis to make it solid. Case-IH does offer a solid ball-style drawbar but at extra cost.”
Bill Garber, Delavan, Wis.: “This ‘floating head’ should be enlisted for submarine duty,” says Bill about his 1988 Deere 915 cutter head. “We made numerous adjustments, butitstill insists upon picking up soil and stones. My wife and I are trying to decide whether it’s better suited to pick peanuts or potatoes, Regardless of manufacturer’s reports, the plastic fingers on the reel do snap in weedy conditions.” On the positive side, Bill is pleased with his 1987 Case-IH 2096 tractor. “It's the mosteconomical tractor I’ ve owned and the front-wheel assist is great. I'm a polio victim, but I have no difficulty getting in and out of the cab. The controls are conveniently located, the visibility is excellent, and the hydraulic seat is comfortable.”
Joe Newcomer, Brinklow, Md.;: Joc ha: had good luck with his Case-IH quick at tach adapter which converts the front-end loader bucket on his International 225( tractor to a fork lift or snowblade “in minutes.” However, he has had problems with his Buffalo metal-cutting band saw. “The blade wasn’t matched properly in the roller guides so it wouldn’t cuta straight line, Finally the roller guide fell apart. The company wouldn't make any adjustment nor would they take the unit back. It’s a $189 piece of junk.”
John Benedict, Caledonia, N.Y.: John likes his Deutz-Fahr DX160A tractor. “Drives well, has excellent fuel economy. However, the hydraulics could be improved.” On the “worst buy” side, John nominates his Case-IH spring-cushioned disk. “I’ve broken several spring hangers on the front gangs and the heavy wing irons keep breaking loose at their pivot points.”
Louie Christensen, Nome, N.Dak.: “My DMI ‘Tiger Two’ 7-shank deep ripper was in the shop for warranty repairs for two of the first three months after I bought it last August,” says Louie, who operates the ripper at 14-in. depths. “Our dry fall should have been ideal for shattering the hardpan. However, the ripper couldn’t handle rocks despite being equipped both with spring tripsand shear bolts. After 475 acres, four of its seven shank assemblies were sprung. The geometry of the spring trip is faulty because it requires more upward motion than backward motion to trip, so it works only on ‘round-top’ rocks. I use grade no, 2 shear bolts as recommended, yet! still have 20 Ibs. of sheared bolts lying in the tractor cab to prove that they don’t work when they hook a rock solidly. The shank assembly bends sideways and tries to go around the rock. Side thrust is transferred upward to the draft links and is multiplied by the leverage involved, However, the links can’t take that much stress in that direction. The bent shanks ride out of the ground causing the machine to pull crooked, Asa result, soil abrasion is transferred to soft steel on the side of the point instead of on the hard surfacing at the tip. DMI replaced all bent parts, but with duplicates of the original. I fail to see how this can remedy the problem because the design has been proven inadequate. By next fall the warranty will have expired which, I suppose, will cure the problem for DMI.” On the positive side, Louie ranks his Case-IH 496 spring-cushion 28 1/2-ft. wide tandem disk as a “best buy”. “Although I pull it at 6 1/2 mph, rock damage has been minimal. The lengthwise cushioning of the suspension members, as well as the vertical movement of the gangs, absorbs enough shock to make disk or spool breakage a rarity. My only criticism concerns the gang hanger bearings. Flexing of the cushion springs causes some of the spherical race bearings to turn in their retainers, resulting in misalignmentof the grease fittings so that they no longer accept grease. There’s no way to correct the misalignment.” Another “best buy” is his 1979 Steiger $T270 tractor powered by a 3306 Caterpil( / 3-/— FARM SHOW - 13 Best & Worst ( lar engine. “I've made only minor repairs to an injector tip. At nearly 5,000 hours the engine seems to work as good as ever and emits no diesel smoke unless pulled below governed speed.”
Elijah Gordy, Delmar, Del.; A 1988 Case-1H 5100“soybean special” drill heads Elijah’s “best buy” list. “I’ve used it to drill 600 acres and it has done a super job, spacing the seed perfectly. The large seedbox means less down time for filling. I'd recommend this drill to anyone.” Elijah has also had good luck with his 1987 Case-IH 2096 tractor with front wheel assist purchased from Tull Bros, Seaford, Del. “The dealer has done an outstanding job of keeping us on the job. He replaced two oil seals on two separate occasions, and we were back to work in a short time. The tractor performs like a winner, particularly in wet conditions.”
Henry Klehm, Chatsworth, Ill.: “It produces clean grain, handles easily, and we can’t believe how easy it is to set,” says Henry, pleased with his 1986 Case-IH 1640 combine which he and his father bought used, They equipped it with a new 1020 bean head and a used 844 corn head. A 1987 M & W 1160 Earthmaster ranks as their “worst buy”. “The trip shanks don't work well in rocks or hard ground. We installed extra springs in the trips which caused the brackets holding the shanks to break. Last fall we traded this model in for anew M & W 1165 model with springloaded automatic trips which solved the problem.”
Don Myers, Spring Mills, Penn.: “Excellent power and fuel economy, and it’s the only 65 hp tractor on the market with a true power shift,” says Don, pleased with his 1987 Case-IH 1394, “It's areal pleasure to drive, especially when we're using ptopowered equipment. No problems.”
Bernard Martin, Willow Bunch, Sask.: A 1987 Case-IH model 1010 25-ft. straight cut header is Bernard’s “best buy”. “We're in the custom combining business and have cut over 7,000 acres with this header without a minute of downtime, The knife is fast and cuts clean even at 6 mph. It’s a topnotch product from a reliable company. “Another best buy is our 1984 TH 1460 Axial Flow combine. The reliability of this machine is unreal. It has threshed about 15,000 acres with no downtime other than regular maintenance.” Bernard also is happy with his 1980 Versatile model 835 4-WD tractor. Very efficient, powerful and reliable.” On the negative side, Bernard is disappointed with his Wrenn 3/8-in. electric variable-speed reversing drill. “It's notbuilt strong enough to handle even easy jobs. I used itto install two truck tarps and stripped the gears in the chuck.”
Otto Kaschmitter, Paynesville, Minn.: “We've baled about 12,000 bales without a miss,” says Otto, pleased with his Case-IH 5420 baler equipped with a bale thrower. “The baler has good capacity and the thrower, which features hydraulic controls with self-contained electric switches, is easy to control.” Otto also likes his 1980 International 1460 Axial Flow combine. “It just keeps on running. Never any down time.”
Oliver Oswald, Eureka, S.Dak.: “It’s the best swather I've ever used,” says Oliver, happy with his new 6000 Case-IH 21ft. grain swather equipped with a double swath mechanism. “We’ ve puton 300 hours with few problems. However, the swath shifting mechanism should shift faster. A bigger hydraulic cylinder would alleviate the problem.” He also likes his Vermeer 605J Auto Weave baler. “If we had to replace it, we’d buy the same model again. It’s a well built machine, as is our Case-IH 1460 combine which has needed little maintenance.”
Paul Kuhn, Genoa, Ill.: “It’s the most comfortable, quiet combine I've ever used, and has plenty of capacity,” says Paul about his Case-IH 1660 combine. “I can pick 150 bu. corn at 6.6 mph. We had a New Holland TR70 before this one and it had much less capacity. It’s like comparing a Volkswagen to a Cadillac.”
Raymond Rumford, Ottawa, Kan.: “My worst buy is a 1986 Deere 4425 combine. Deere mislabeled this combine. It should have been labeled the “GrinderMixer”. grow soybeans for seed production, and the combine ground up 35% of my 1987 soybean crop. The seed company rejected the seed, and it cost me thousands of dollars. Deere doesn’t know how to solve the problem.” Raymond says his 1987 Case-IH 1620 Axial Flow combine is his “best buy”. “It has great capacity, is quict, easy to operate, and produces a super grain sample.”
James Leonard, Waunakee, Wis.: His “best buy” isa 1988 Case-IH 8520 baler. “It straddles the windrows, ties good square bales and distributes leaves evenly throughout the bale.”
Stanley Hueske, DeWitt, Neb.: “My “worst buy” 1984 Deere 4250 tractor uses more than twice as much fuel than the Allis Chalmers 7000 it replaced. It pulls like a 100 hp. tractor in the field even though the dealer’s dyno shows 140 hp. It takes more time to pull a load with it. (My 11-year-old 2-135 White tractor pulls loads 35 to 40% faster.) Visibility is poor and the steering ratio is the slowest in the industry. I re-did the entire forward lighting system. The grill lights are a joke and the 3-pt. is slow, although we can’tseem to stop it from making 3-in. jumps during hookups. It’s also hard to see the 3-pt. from the cab. A gear went out of the transmission during cultivation and I was down for 10 days. The only thing I really like is the power shift transmission.” On the “best buy” side, Stanley’s happy with his 1987 Case/IH 1660 combine. “It's gothigh capacity with clean grain. I like the 20 mph road gear and it's quiet to operate.”
Albert Preston, Wenona, Ill.: “I read with interest the report in the last issue of FARM SHOW from Joe Park, Tupperville, Ont., who said he’d broken three axle yokes on his Versatile 895 tractor, and that Versatile’s response was that he was the first person who'd ever had that type of breakdown. Well, we've had the very same problem with our 850 Versatile and were told the same thing — that ours was an unusual, isolated case. Baloney! “This is a serious, widespread problem which Versatile refuses to recognize. I'd like to hear from other owners who've also had problems with axle breakage. Maybe we can get together to initiate a class-action solution to the problem, if that’s what it takes to right a wrong. “We've had two broken axles on our 850 since we purchased it new. However, since it had stood in stock for two years, the company called ita two-year-old tractor out of warranty and refused to pay for the repairs. The axle problem is with the cast iron housings or yokes, Initially, they came with a small hole in them which apparently was to accommodate a painting hook. They’ve removed this hole in new replacement housings but it still hasn't solved the problem. A neighboring Versatile owner who's experienced four broken axle housings with Mas Qninate suys holes just broke a fifth — which didn’t have this hole. My son won't even drive our 850 for fear that another axle will break. When it does, the tractor suddenly stops and drops down, exposing the driver to possible severe injuries. If this breakage happened on a busy road, hard telling how many people might be injured or even killed. Versatile lied in telling me I was the only one with this problem. They should recall all affected tractors and replace the cast iron housings with steel —before somebody gets killed or seriously injured.”
Robert J. Scott, Danbury, Iowa: “We're happy with the Cam Spray 330 MT high-pressure washer with a 5-hp. Honda gas motor we bought at our Case/IH dealer . I’ve owned it for a year and have had no problems whatsoever. It will run all day at 1,200 psi without a hitch. The motor is extremely easy on gas. We use it for everything from washing cars and tractors to cleaning out hog sheds.”
Pete Williams, Decatur, Ill.: “I thought Deere & Co. made the best combines until many of my neighbors switched to IH Axial Flow machines,” says Pete, well-pleased with the used 1979 IH 1460 Axial Flow combine he bought. “It’s got more power, less noise, less dust in cab, it’s simpler in design, is made much heavier, and is much easier to service than Deere combines I’ve owned. There is virtually no split grain in the hopper. Even though the combine had 1,700 hrs. on it when we bought it, we’ ve harvested 600 acres with it with no breakdowns. With the help of a Bish header adapter (Harvey Bish, Giltner, Neb. 68841), I equipped the combine with a Deere comhead and row crop head. They make an excellent combination.” On the negative side, “One of the worst buys I’ve made is anew 1985 Case/IH 800 6-row planter, The dealer delivered it with a broken seed nose, a broken seed manifold, misaligned seed release wheels, a defective seed hopper level sensor, a defective seed drum sensor, two seed closing disks that would not turn, a torn seed drum seal that was leaking corn, and a bad monitor. The dealer offered no help and after I worked on it and lost 4 days, I called another dealer who worked on it for 1 1/2 days. At least Case/IH stood behind their warranty and it didn't cost me any money.”
Jack R. Kiser, Fremont, Ohio: “FARM SHOW is my best buy. I read in your last issue about the farmer who saved money by buying a replacement fan at a NAPA auto parts store rather than at his farm equipment dealership. I needed a double-shaft 12-V fan motor for my tractor cab. The cab's manufacturer, Year-ARound, wanted $100 for the fan. My Case/ IH dealer quoted a price of $112, Then I tried NAPA, They sold me the same fan for $53. FARM SHOW saved me a lot of money and prevented this parts rip-off.”
Gary Morrison, Mooretown, Ontario: “Our 1987 Case-International 685 row crop tractor is the ideal size for general purpose jobs. Operator controls are all easily accessible and out of the way for driver comfort. It’s powerful enough when planting and row crop cultivating to operate in a higher gear at much lower rpm's. It demonstrates very positive steering and turns on a dime without using the brakes.”
Neil Kruger, Warren, Minn.: “My 1985 Volkswagen Jetta diesel auto has good power, handles beautifully, is very comfortable, and gets 45 to 50 mpg. At 50,000 miles it has given no mechanical problems, “Our 1480 Case-IH Axial Flow combine does an excellent job harvesting small grains, soybeans, corn and sunflowers. Good dealer service, too.” On the negative side, “Our 1983 Ford F250 4-WD diesel pickup has given problems right from the start, burning out glow “The dealer wouldn't admit that he didn't know what the problem was.” plugs regularly. The dealer wouldn't admit that he didn’t know what the problem was. After 3 years and much out-of-pocket expense we finally got Ford to solve the problem. The diesel pump also was faulty and had to be overhauled. It drives nice but gets only 15 to 20 mpg with no load.”
Vernon Schulze, Humboldt, Iowa: Vernon’s been pleased overall with his 1987 Case-IH model 14 V-ripper chisel. “I had a problem at first. One of the automatic spring trips came apart because it had not been put together right at the factory. But the serviceman and I figured it out. I removed all the trip shim blocks because the shanks tripped too easy. [havea lotof rocks and it’s doing a fine job now.”
Fay Ellwanger, Garden Prairie, Ill.: “We're happy with our 1987 Case-IH 2096. The cab is quiet, it has lots of power for its size, it handles well, controls are handy, the engine is easy to service with the pop-up hood, and the new-style cab provides great visibility.”
Dave Winegar, Moorhead, Iowa: “I thought my 6620 Deere was a good combine till I got my 1987 Case-IH 1660 Axial Flow. It has a cleaner grain sample, less cracked grain, a quieter cab, better vision, more power, fewer moving parts and it uses less fuel.”
Roy T. Johnson, Dows, Iowa: “My 1987 IH/Case combine is the best and the most easy to operate of any combine I’ve ever owned. The new bean and corn heads are easy to change. It’s a good machine and dealer service is good.”
Doran Zumbach, Coggon, Iowa: His 1986 Case/IH 1660 combine with a 1063 cornhead heads his “best buy” list. “It’s got a big roomy cab and lots of capacity. We can combine in excess of 1,300 bu. per hour with an almost perfectly clean grain sample. It’s trouble-free, easy to work on, and easy to start in cold weather. This is the first IH machine I’ve ever bought. “My other best buy is my Dataline information service. We receive a tremendous amount of information daily for less than 65 cents, That's a real bargain.”
Marlyn Bordson, Wanamingo, Minn.: “I’ve been very happy with the quality workmanship and service.of my 1988 Chevrolet Scottsdale pickup,” says Marlyn about his “best buy”. Calvin M. Schuk, Tatla, Lake, British Columbia: “Our best buy is our 1986 Versatile 256 bi-directional 4-WD tractor. “It's got good traction, good flotation, and a comfortable seat.” It’s got good traction, good flotation, and a comfortable seat with excellent placement of hand and foot controls. You can swivel smoothly to switch the direction of travel, and I like the hydrostatic drive which gives us instant forward or reverse. We were also pleased when the engine warranty was upheld. A Cummins mechanic drove over 200 miles one-way to replace a faulty turbo charger.” Also on the “best buy” side, Calvin’s happy with his 1987 Husqvarna chainsaw. “It’s light, cuts fast and we have a good dealer, only have been driven on pavement. It wasn’t made for off-road work,” says Kent about his “worst buy”. “It’s geared too fast in first and reverse. First was too fast for travel over a rough pasture and it takes a lot of skill to back it up a hill or in loose ground without killing the engine. A stick or cornstalk can easily knock off the plastic hub caps. The box is lightweight and easily dented, The front fenders are too narrow so that mud flies up and lands in your lap if the window is open and there is across wind, In mud, when you notice a loss of power, you have to get out and dig the mud out of the end of the exhaust pipe. At29,000 miles I had to replace the expensive front drivehsaft C.V. joints.” On the positive side, “Our 1987 Case/IH 1660 combine threshes well and cleans grain with little damage. A very nice, clean quiet cab.”
Kent Krause, Adams, Neb.: “My 1983 4-WD Chevrolet S-10 pickup with a V-6 and 4-speed manual transmission should JO. |] #£x§€ ARM GHOW «e 13 only have been driven on pavement. It wasn’t made for off-road work,” says Kent about his “worst buy”. “It’s geared too fast in first and reverse. First was too fast for travel over a rough pasture and it takes a lot of skill to back it up a hill or in loose ground without killing the engine. A stick or cornstalk can easily knock off the plastic hub caps. The box is lightweight and easily dented, The front fenders are too narrow so that mud flies up and lands in your lap if the window is open and there is across wind, In mud, when you notice a loss of power, you have to get out and dig the mud out of the end of the exhaust pipe. At29,000 miles I had to replace the expensive front drivehsaft C.V. joints.” On the positive side, “Our 1987 Case/IH 1660 combine threshes well and cleans grain with little damage. A very nice, clean quiet cab.”
Leonard Fehr, Gladstone, Manitoba: “My best buy is my 1981 Versatile 875 4WD tractor. It has over 3,000 hrs, on itand we have not spent $100 in repairs on it yet. It handles very well and has lots of power. Another best buy is our New Holland TR95S combine. It’s easy to set and has lots of capacity. The Cadillac of combines today. “My 1985 Case/IH 44-ft. vibra tiller cultivator is my worst buy. Axle bushings on the tandem wheels wore out the first season, They were replaced. The same thing happened all over again the next year. The wings on this machine always go deeper than the rest of the cultivator, which we fixed by putting spacers on the cylinders. It takes about 1/2 hour to set the cultivator right, The harrows are junk, They don’t have enough adjustment on them. If we didn’t have a good dealer, would have traded it off the first year.”
Garry Hill, Langruth, Manitoba: “In 1982 we bought a 1690 Case tractor with 500 hrs. on it. It’s been our worst buy ever, We've had endless trouble. The first spring the motor went out. All summer main hydraulic lines would break. We've replaced two hydraulic pumps on it. A frost plug went in behind the flywheel at 1,200 hrs. so the tractor had to be split. The air “This tractor consumes more fuel than any other machine I own.” conditioning compressor was mounted poorly so that the torque of the compressor broke the thermostat housing off. This tractor consumes more fuel than any other machine I own. We've gotten no satisfaction from the dealer.”
Richard L. Newton, Marengo, Ind: “The LT30 Woodmizer sawmill, which I bought three years ago, is the best piece of equipment I have ever owned, It's easy to operate, seldom needs adjustments (which are easy to make in any case), and performs just as the company says it should. The company's great about providing updates on their research and the findings of other mill operators. Service is tops.”
Leo P. Bergin, Yerington, Nev.: “I found my best buy Keltgen tires through FARM SHOW. I needed narrow tires and wheels for high hp. tractors used in row crops. Although the arrangements for the purchase of the specialized tires were via a long distance phone call, the tires and wheels supplied were as represented and rim construction quality exceeded the original manufacturer's specifications. The price was fair and delivery was as stated. I was so pleased with the first set that I ordered a second set of tires and wheels for another tractor. These, too, were perfect. “Other best buys have been a Ford TW 35 tractor with mfwd. It’s fuel efficient, trouble-free, comfortable and has more pulling power than other tractor makes with the same advertised hp. [also like my Ford 7710 which hasn't had any problems in 2,000 hrs. of use.” Lawrence Peterson, Ayrshire, Iowa: He likes his 6-ft. wide 1982 Woods belly lawn mower. “It's wider than the wheels on my Case tractor, therefore the tires don’t run the grass down. [ mow about six acres a week and have only needed to replace 2 belts and 2 sets of blades.”
George Smoot, Milford, Del.: “I’m 74 years old and have about 14 acres of tillable ground. Ihave anold S.C. Case that that doesall my work. It was made in the late thirties but still runs and works okay. “I’m also well-pleased with an International 782 Cub Cadet that I bought three years ago.” Kenneth Herdrich, Greenwood, Wis.: “I haven'thad any problems with my 1986 Dari-Kool DKF 800 bulk milk cooler tank. Good service from the company.” Charles A. Mercer, Strathmore, Alb.: Charles nominates his 1982 Hesston 1014 Hydra-swing pull-type hay windroweras “best buy”. “The machine has been trouble free from day one. It was assembled (including optional equipment) and serviced well. It's worked great mowing hay ever since.”
James Rocheleau, Barton, N.D.: “My Wilrich 8-18 hinge frame plow plows beautifully and is strong, but it’s next to impossible to change depth after changing lays. Also, when I get into mud, I can’t raise it slightly to get through without wrecking the rear furrow. Thus the next furrow is also thrown out of whack. The furrow wheel rubs sideways against the furrow wall constantly. We can't seem to adjust it so the wheel will run straight.” James names his 1985 Dual 3100 Quick Tach loader as “best buy”. “It’s a strong loader with cylinders that don’t loosen up too bad on the ends. Overall, it’s a well designed product built to last. But, I didn't like their flimsy grapple fork, so I built my own. Also, their mounts stick the loader out too far, so I built some that mount it tighter to the tractor front end,” Victor Jim Dubbert, Laddonia, Mo.: “Our best buy in the last year has been asetof skid plates from Poly Tech Industries, Monticello, Ga. for under the combine header They help keep dirt or mud from getting in with your grain, Wealso like our 2594 Case tractor. It’s trouble-free and has plenty of power.” Patrick Matthews, White Oak, S. Car.: “A 1986 Vermeer 605-G hay baler is our best buy. It’s much improved over previous balers we’ ve used, It starts making bales quickly and gives more even distribu)/- <7 FARM SHOW « 13 Best And Wors (Continued from preceding page, tion of hay because of the ‘open throat’ — design. It's far easier to unclog damp hay out of than earlier Vermeers, However, the method of wrapping twine around the bale should be improved.”
Arnold Wipf, Hawley, Minn.: “I'm proud of my 3594 and 1480 Case-International equipment. The tractor gets excellent fuel economy, has ample horsepower and is well constructed. The combine has lots of capacity and, for its size, is fairly efficient on fuel and trouble-free.”
Kent Butler, Paragould, Ark.: "I'd like to nominate two machines as worst buys. As a 'proud' owner of both a 3588 International 2 + 2 and a 1980 GMC diesel pickup, it's no wonder that IH ar’ ©M both faced and are facing "They should find the engineers that designed these products and make them try to keep them running two days in a row." troubles. They should find the engincers that designed these products and make them try to keep them running two days in arow, "As best buy, I'm proud of my 3594 Case-International. Sure am glad Case designs won out in the merger."
David McKee, Lewisville, N.C.: “The first year we used our Niemeyer “Anyone making hay shouldn’t be without one.” HR 301 tedder it paid for itself two times over by allowing us into the fields on little notice to make hay between rain showers. Even with a little rain, we can stay in the field when everybody else is waiting for their hay to dry. Anyone making hay shouldn't be without one." William J. Rice, tional 205 combine. It had been welltaken care of and was one of my best buys until Case took over the company. I have a lot of IH farm tools and tractors, but now when I go into the new Case-IH dealership, the parts man smiles and says ‘Sorry, that part's no longer available’, Yet, you can get anything you want for Case products. I’ll never buy anything red again.”
Mark Rathbun, Maywood, Mo.: “In 1978 I bought a 1973 Interna tional 205 combine. It had been welltaken care of and was one of my best buys until Case took over the company. I have a lot of IH farm tools and tractors, but now when I go into the new Case-IH dealership, the parts man smiles and says ‘Sorry, that part's no longer available’, Yet, you can get anything you want for Case products. I’ll never buy anything red again.”
John Haak, Winfred, S, Dak.: ‘My 1986 Case-International 496 FlexWing cushion gang disk is the best piece of equipment I've ever owned. We have rocky fields and usually spend a lot of time replacing blades and bolts. This year we disked over 2,000 acres without a single stop for repairs. “My worst buy Black and Decker %-in, rechargeable drill doesn’t have enough reserve to drill more than 3 or 4, %s-in. holes in wood. | replaced it with a Makita cordless which works great with plenty of power.”
Gary Charter, Ida, Mich.: Gary nominates his 1986 Case-International 800 Early Riser planter as both best and worst buy. ‘Because of the late spring needed to plant my corn and beans mostly minimum till. My old International 58 planter wouldn't plant in adverse conditions but the Early Riser did a beautiful job. Unfortunately, couldn't get it to space plants evenly no matter what plate I used. Also, it was equipped with a fancy monitor that only worked on one setting. I couldn't get the dealer to come out and fix it at any time during the planting season.”
Gary Dinkel, Culver, Ore.: ‘I bought my 1981 2090 Case tractor when it had 1,000 hrs. on it. It’s performed with no problems for the past two years with the exception of a fuel cap which leaked. Fuel economy is excellent, power is good, the power shift works great, and the cab is as quiet as any on the market. My only complaint other than the fuel cap, is that the hydraulics and pto controls are awkward to handle.”
Gene Endicott, Mcleansboro, ILL: Gene's Case tractors are his ‘‘worst buys". “IT have the dubious honor of owning 3 Case tractors. Since the merger with International, all Case dealers in my area have merged with International dealers. These IH dealers won't stock Case parts. We have to order them, which takes a minimum of two days and can take as long as 5 days. Looks like my next tractor will be green.” On the ‘best buy" side, Gene's happy with his 1900 series Krause disc harrow. ‘After two season of use we've had no problems. Very wellmade. It cuts level and yet is heavy enough for good penetration.” ee a linate into gear at highway speeds, creating a real chatter. Before I replaced them | had them cleaned and greased three times in 6 mos. but it didn't help. | have also replaced the intake manifold twice as well as the rear transmission seal, all within 45,000 miles,”
Renken W. Leners, Beatrice, Neb.: “The worst buy ever made is a Deere Max Emerge plateless planter. It works alright for corn but, when it comes to planting milo, it's a disaster. At 4% to 5 lbs. per acre, it plants very uneven with lots of skips. We haven't “T figure we lost 10 to 15 bu. per acre in yield.” been able to get this situation corrected. figure we lost about 10 to 15 bu. per acre in yield due to the skips it made.” Gene Heneks, Mechanicsville, Iowa: “It's a shame these tractors were discontinued by Case/I.H. We're pleased with the power, traction, and ease of operating and handling. Gear selection is excellent and our dealer has given us good service," says Gene about his 1983 and 1984 International 5288 tractors.
Dale Wiens, Beechy, Sask.: He likes his ‘best buy’’ Midland FM radios. “They're reliable, noiseless, clear and priced right. A real asset to any farm operation,” As ‘‘worst buy"' he cites his Regency Micro-Com 22 VHF-FM /O—/ — FARM SHOW (1) 13 Best And Wi (Continued from preceding page transceiver. “| purchased 2 radios and installed both in places where I'd been using radios for 18 months using the same antennas and power supply, but neither of the new radios worked. After getting them checked out, the dealer found nothing wrong and they still wouldn't work. They finally work now but they're not nearly as clear as my other radios.” Eugene Cysewski, Courtenay, N. Dak., “Our Deere 8650 tractor performs, rides and handles well. Fuel consumption is comparable to our previous Case tractor under similar load conditions. “Another best buy is our Load King grain and fertilizer drill-fill hopper tank. Works good, is easy to clean out and eliminates the need to hoist the truck box in soft fields, which can be dangerous,” Lester Warburton, Chinook, Mont.: “In 40 vears of farming, I've never had anything like it. [can't call it a lemon, it’s more a pile of junk. I purchased a model 57 Rock-O-Matic rock picker in December, 1981. This year is the first year that I used ita full day without a repair. Something is always broken, fallen off or worn out. It hasn't been abused and never had to pick up rocks any larger than a basketball.”
Jim Ifft, Fairbury, IL: Jim's not happy with his Ritchie stainless steel nipple waterers. “They work okay until they need maintenance. They're almost impossible to work on, Hoses break, heaters and thermostats corrode, and insulation falls off. The stainless steel case will probably last forever, but all the inside parts are worn out after 3 years. “T have 2 best buys. My 1984 Mercury Lynx diesel car gets exceptional mileage and is trouble-free, even in cold weather. Also, Trimpe reworked cylinder bars (Rt. 7, Box 145 Seymour, Ind. 47274) are best buy. They turn your combine into a new and improved machine. We get exceptional grain quality and improved capacity.” Dennis Rottinghaus, orst Buys eliminate his drying bins with their sweaty sidewalls, spoiled grain and troublesome stirators.” Dudley also likes his Herschel Tiger Jaws sickle mounted on his 218 Deere beanhead. ‘It increased ground speed and performed as promised.”
Hugh Stueck, Abernethy, Sask.: “On June 27, 1985 we bought a 1482 combine from our Case/ IH dealer. Purchase was made before July 1st to qualify fora cash rebate. We were told the refund would take 4 weeks to process, On August 21st, we received a letter saying the rebate would arrive in two to three weeks. On Nov, 15 we were still waiting. On another occasion, I was told the company couldn't supply a part because they were taking stock in that department.”
Gary Quick, Shattue, IIl.: He’s had trouble with his Case dual offset tandem disk. ‘The disk continually bumps the depth control paddle back each time you raise it out of the ground so that, after 10 acres, the disk cuts so deep you can’t pull it. The dealer replaced the transport cylinders and control valves twice but with little effect. He’s trying to fix it but gets very little help from the company. Otherwise, it's a good disk. “Our 1984 Case 2390 tractor is a “best buy”. It’s very comfortable, has a quiet cab, dealer service is good and I'm pleased with its fuel economy. It uses no more fuel per acre planting than the 110 hp. tractor is replaced. Plenty of power for heavy tillage."
Charles Whitaker, Chilton, Tex.: Charles lists Banvel “Cut Surface Treatment” Brush Control as “worst buy". “I used it exactly as the dealer recommended — that is, to cut brush and spray cut surface. However, I got practically no kill on mesquite or mulberry. “My best buy is Tuf-Mac 12% ga. barbed wire. I bought it for $3 less than other domestic top-of-the-line barbed wire and it performs as well as any I've ever used. Stretches tight and stays tight. Not one break while stretching and working with it.” Ronald Jorgensen, Ward, S. Dak.: “It's just a super machine — the most dependable tractor I’ve ever owned. use it year around and have the third set of tires on it now," says Ronald, happy with his 1964 731 Case diesel.
Joseph Holecheck, Federalsburg, Md.: "I hate to see the International tractor line stopped by Case-IH, I've never had an IH tractor give me trou- ble. [ just bought a 3288 tractor and have a 5288 which I really like. I'm also real pleased with my IH Cyclo air planter."
Stanley Getlinger, Hortonville, Wis.: He has mixed feelings about his Knight Mini Augie feed blender. "We have far from attained the milk pro- duction speculated upon prior to the sale but are slowly gaining now. Also, because of an improperly ground sprocket, the shaft on two dif- ferent augers bent. These were re- placed by the company at no cost. Service from Knight has been out- standing. There was also a problem with the main gear case. They re- placed it also, "Our Servo Vacuum controller from DeLaval is a best buy. We re- cently installed it to replace two Surge oil cushion controllers. The DeLaval controller is very stable and doesn't allow the vacuum to increase beyond the set level as the Surge did."
Edwin C. Young, Orangeville, Penn.: "It's my second Stihl. I pur- chased my first one in 1978 after own- ing many other saws," reports Edwin, pleased with his Stihl Farmboss chainsaw. Arlo A. Dewald, Tripp, S. Dak.: "This tractor has been nothing but trouble. I've had trouble with just about everything except the engine. I put in two clutches, ring gear, and pinion. I've had many other problems in almost 2,000 hours. The dealer and company have been fair about paying for part of these things, but you don't know what to expect next," says Arlo who nominates his 2290 Case as "worst buy". He's had good luck, however, with his Deere 4040. 'This tractor per- forms real well. It's only been in the shop once and that was to put a small seal in the pto."
Norman Welch, Virden, Man.: “My 2090 Case tractor works fine and service is great, but it's only a year old and still on warranty and the company tells me it needs an update on the rear end which will cost me about $600. If 1 don’t get it done, the tractor will be worth less when I trade it in. I feel this is their problem, not mine.” On the “best buy” side, Norman nominates his %-ton J-20 Jeep with 4-speed transmission. ‘It's marvelous. Delivers 12 large round hay bales at a time on a fifth wheel trailer with no limit of power and traction.”
Oscar Matzinger, Oregon, IIl.: ‘My number one best buy is FARM SHOW. It’s truly a farmer's magazine — not a herbicide, fertilizer and insecticide advertisement,” says Oscar. He also nominates his 430 Case tractor and Troy-Built roto-tillers as best buys. “The Case is the biggest little tractor we've ever owned, We (Continued on next page.) ey —_ ee Best And Wo (Continued from preceding page) bought it new in 1967 and it’s never needed a major overhaul. The tiller has been a joy to operate for all large garden work. We do 342 acres with it. It's a flawless machine."
Jeff Duorak, Stuart, Neb.: He's well satisfied with his 1982 Deere 8640 4-WD. “We traded a 7520 Deere for this tractor because we needed more horsepower. We've put more than 1100 hours on it and not a thing has gone wrong. It's a very fuel efficient machine.” Jeff had some trouble with his International 1466 with front wheel drive. ‘This tractor has dealt us a fit. The pto went out twice and we had to rebuild the engine on it.” Randi Suckut, Bowdon, N. Dak.: “I really enjoy the quiet cab on my 2290 Case. The tractor’s also easy to maintain with its lifting hood and swingout battery.” Randi also lists his Chevrolet Celebrity as a ‘‘best buy”. “Gets 31 mpg., rides and handles great and is also quiet.”
Ray Huggins, Challis, Idaho: Ray's had trouble with his “worst buy” 1983 GMC 6.2 L diesel 4-WD pickup. “At less than 29,000 miles, the transmission exhibited a pronounced jerkiness, power was substantially diminished, the transfer case refused to disengage from 4-WD, it emitted excessive white smoke, and developed an engine oil leak. returned it to the dealer and was told that some of the ‘gasket-in-a-tube’ with which the transfer case had been assembled had found its way into the shifting mechanism, causing it to stick in 4-WD. In addition, the rear main seal was found to be inoperative and both the flywheel and starter were damaged or defective, necessitating the replacement of those parts. “When I returned a week later it had developed an oil leak in the transfer case together with the engine oil leak. We found out that the white smoke and low power condition of the engine was caused by the fact that one cylinder had approximately 100 lbs. less compression than the others because the one cylinder lacks a prechamber. The other cylinders are also low on compression and need a complete ring job and installment of the missing pre-chamber. Finally, we discovered that a burr on the crankshaft is destroying the rear main seals and must also be replaced."
Howard Koehn, Copeland, Kan.: “I love FARM SHOW magazine,” says Howard who also lists his ComputN-Acre from Agri-Tech as his “best buy”. “I've been absolutely amazed with all the functions I've found for this unit. It’s a tractor-mounted acreage computer that put on my 2590 Case. I use it to calculate total field acres, acres by the round and also mph. It has proven to be accurate and I'd hate to be without it.”
Ron Skopyk, Hepburn, Sask.: “This tractor doesn't deserve all the criticism other dealers give it,’ says Ron, pleased with his 2390 Case tractor. “It's an all-around good tractor with handy controls and a quiet ride. Service is good.” He’s upset with his Allis Chalmer's 616 garden tractor. ‘The tractor is alright but the lawn mower attachment is junk. Bearings are falling apart, the belts fall off every time the mower is lifted, and the blades work loose, ruining the splines on the shaft.”
Glen Stenzel, Hamburg, Iowa: “We traded our 1978 8630 for a Deere 8650. That was a mistake. The 8650 was a demo with 175 hours on it, which should have meant all the new-tractor bugs would be worked out. Unfortunately, this was not the case. The gear shift knob continually falls off. The tractor is hard to shift anyway and, without the knob, it's almost impossible. The hydraulics often refuse to lift the 3-pt. and fuel leaks from the injection pump make the engine hard to start. The alter nator doesn't keep up with demand so batteries discharge. Flood lights go out after 30 to 45 min. of use. The hydraulic seat raises itself during operation. The right speaker on the radio has been replaced and still doesn’t work. There have been several oi] leaks in the hinge area and they're hard to find and harder to correct, and the turbo charger went out during the winter. The digital tach was not programmed correctly for the tire size. “When informed of these problems, Deere and its dealer organization have trouble believing that anything with green paint can have a mistake or problem. Most of the problems could be worked out if everyone worked on the solution instead of arguing and assuming the equipment has been misused. We have driven Deere tractors for 30 years and have always had good luck with them until now. We're trading this 8650 off with just 350 hrs. on it, something thought would never have to do.”
Glen Dugger, Sigourney, lowa: ‘I was forced into purchasing a new Morton pole barn after a fire and they did an excellent job of construction. There’s not one nail hole leak in the roof. The building looks good and can stand up to strong wind.” On the negative side, Glen's unhappy with his Black & Decker 4¥-in, angle head grinder. “It's an industrial model but has a plastic case. It lasted about 18 months. It's not worth fixing because the plastic case is warped.”
Larken A. Watson, Deadwood, Alberta: ‘Our Deere 2320 swather with an 18-ft. head cut 2,200 acres last year with no problems atall,” says Larken, who farms some of the northern-most cultivated land in North America. “Really appreciate the cab, air con“Tt cut 2,200 acres with no problems at all.” ditioner, heater and our helpful dealer. We also have a 1370 Case which has been an excellent buy. Lots of power.”
Ed Runty, DeWitt, Neb.: “It's designed for lawn watering but works great for cooling or watering livestock as well,” says Ed, pleased with his Rainmatic computerized water control unit bought from Rainmatic Corp., P.O. Box 3321, Omaha, Neb. 68103: “It’s a small device that can be attached to any hydrant or hose to control water flow. I've used several units to keep hogs cool in summer “T use it to keep hogs cool in summer heat.” heat. It's inexpensive at less than $50, operates anywhere on four ‘‘D"’ alkaline batteries all summer long, and is very accurate and reliable. I can go to the field or be gone all day and not worry about turning misters on and off. It has two daily schedules with four cycles apiece so it can turn water on up to eight times.” Don Feist, Berlin, N. Dak.: “My 2290 Case handles well, has a quiet cab, plenty of power and we've had good dealer service. feel Case has put together a real fine tractor. Servicing is easy and it's easy on fuel. The ride is not the best but an extended front-end kit is available.” Don's 2745 Massey is a ‘worst nt) buy”. “This tractor used 2 quarts or more of oil every day from the day it was new. Then the number one cylinder froze the rings at 900 hrs. After it was fixed, didn’t make it home from the shop before the power shift went out. Total bill was $5,600 and the dealer helped out, which I appreciated. However, wouldn't own one again.”
Gerald Casler, Ft. Plain, N.Y.: He likes his New Holland hay equipment. “We've got a 320 baler, a 358 rake, a 495 Haybine and all are best buys. We also have four Gehl forage harvestors and several Gehl blowers that have given good service. “I bought a new Case tractor too. It has a nice cab and was a good buy because of rebates and a good trade-in allowance. I don't like it as well as some of my old Oliver tractors, however.”
Jim Ifft, Fairbury, Ill.: 'We've used our 1816 B Case skid steer loader for five years and with only a couple small problems which were easily repaired. We've had mixed results, however, with our 1978 Ford F-150 4-WD pickup. I love the way it rides and drives and the 400 cu, in. motor has 110,000 miles on it without any trouble. The problem is the ¥2-ton transmission and rear-end which are too light to pull grain wagons and stock trailers. They've had to be re- paired several times and replaced once. Also, the truck just eats up tires no matter how we adjust it. "Our worst buys are a Deere 110 mounted field cultivator and an EZ Flow 300 bu. side unload wagon. Both are built light and poorly en- gineered. They've required patching, welding, and beefing up almost every season."
Dan Buerkle, Plevna, Mont.: ‘“My International 4386 4-WD tractor is a prime candidate for a worst buy,” says Dan, “The replacement list, at 1,400 hrs., reads as follows: radio, batteries, starter, two axle seals, transfer case seal, oil pressure safety switch sending unit, ether, injection line, radiator overflow tank, electronic tachometer module, water pump, throttle cable, alternator, air conditioner compressor, and various other air-conditioning parts. We have learned to live with-light housings that rattle, a poorly functioning mechanical decelerator, electronic controls that read incorrectly in high humidity, welds that keep cracking, and a malfunctioning parking brake, “If this is quality, we won’t buy another” radiator, and front differential oil sending unit. We also own an International 4100 tractor with 5,400 hrs. and a 1206 with 7,600 hrs., anda 706 with 8,300 hrs. All have been properly maintained and have given good service, but if this is the quality of the new IH tractors, we won't buy another. “Another worst buy is the dye marker kit that came with our Century sprayer. Although the sprayer itself is well-built, the dye marker kit is very unsatisfactory. The dye is too expensive, does not go far enough and is not a bright enough color to be seen at any distance.” On the “best buy” side, Dan likes his International 7100 hoe drill and end-wise transport system. ‘We like the penetrating weight and good overall design of the drills. Except for inaccurate seed metering calibration and the inevitable new machine debugging process, they have given good service and do a good job.”
Steve Pluhar, Cohagen, Mont.:''As a worst buy I nominate my 2090 Case tractor,” says Steve. ‘There was no way to keep from grinding gears and the power shift transmission was hard to shift. It would sometimes stick in reverse so I'd have to sit and wiggle it for 5 to 10 minutes to get it out. The fuel cap always causes dirt to fall in the tank. The door would not hold itself open, and’the tractor was too rough riding.” On the positive side, he's been pleased with his Deere 4440 and 4840 tractors, ‘‘They’ve been almost trouble-free and have good power. They both have a power shift transmission that works real well.
Murray McIntyre, Burns Flat, Okla.: "I bought a Double Torque 2XT auxiliary transmission for my new Chevrolet 1-ton pickup from Power Torque Industries, Inc., Ar- lington, Tex. The unit is supposed to split the gears giving you an extra set of in-between gears. In a little over a year, it failed completely once, and was removed, repaired and replaced four additional times prior to com- plete failure. In addition, it was re- sponsible for the unnecessary re- placement of three heavy-duty Chev- rolet clutches due to failure caused by oil contamination from the Double Torque transmission. "This add-on has a very bad shrill scream and overheats even with the optional oil cooler and pump. The only parts I haven't replaced, in- cluding the transmission case itself due to bad factory machining, was the Eaton electric shift unit which comes with the transmission. "The Double Torque 2XT experi- ment cost me in excess of $4,000 but my Chevy pickup is once again per- fect. The unit has been removed. If anyone wants this kind of trouble, I'll send them my old burnt transmission free." ~
Alan Jay Petersen, Jamestown, Kan: He bought two pieces of used equipment, a 970 Case tractor and a 1979 Chevrolet Caprice Classic car, which are his ‘‘best buys’’. “The Case 970 with cab is easy on diesel fuel, at approximately 3 gal. per hour, There’s no gear noise in the cab, excellent air conditioning, and good lugging power, The 1979 Caprice is quiet running and so comfortable it’s comparable to a Cadillac. Has all the options I like.”
Miron Ackley, Marble Rock, lowa: He likes his Case 885 utility 3-cyl. diesel tractor equipped with a Case 55 loader. “This tractor has lots of power for its size with real powerful hydraulics. It is also economical on diesel fuel, The only problem has been a burned out alternator.”
Malvin Merja, Sun River, Mont.: “This is a high-production implement that can be set to do quality work in either good or poor conditions. It's easy to use, folds up to a good road size and easily gets into places which are difficult to reach with our other disks,” he says about his Krause 200 42-ft. disk. R.F, Hawkins, Copley, Ohio: ‘Case equipment is very easy to operate. This is the second pair of Case 450 crawler tractors I've owned. They run good and the service is excellent.”
William Pylatuk, Watson, Sask.: “My best buy is an 1175 Case tractor. It's the most rugged-built machine I've ever seen. Very durable motor that doesn't use oil and the transmission matches the horsepower. A good tractor all around.”
Tom McManimon, Rushford, Minn: He lists his Case 1737 skid steer loader and his 1979 Ford F250 4-WD, 4-speed pickup as “best buys”. “The skid steer loader is built like a tank. Its easy starting water cooled engine, easy maintenance and large load-handling capability make it a joy to operate. The pickup has done everything but plow the back forty and still runs great.”
Philip Wilson, Lewisburg, Tenn.: “My best buy would be my 2290 Case tractor. The tractor has more horsepower than its rating. The fuel economy is very good. The cab is comfortable and the hydraulics are superior to any tractor have ever had any experience with, ‘The dealer is also good. “Another good buy is my 605 Vermeer round baler. This machine has given six years of service with only modest repairs in key wear areas. The baler has paid for itself several times and hopefully has several more good vears left.”
George Oliver, Fairview, Alberta: His 1981 Case 4490 tractor heads his list of ‘best buys’’. “It's a very reliable tractor, comfortable and quiet. This tractor gives me perfect service. Fuel consumption is good and visibility excellent.”
Leo Bottoms, Dumas, Ark.: “My Hustler rice levee sprayer would be my worst buy,” says Leo. “The engine failed, we had repeated clutchvariable speed pulley failures and wheel drive chain breakage within the first year. The steering clutches are oversensitive to the point that you can't operate them smoothly enough to prevent overstress to the machine and operator alike. A hydrostatic drive system would make it a much nicer operating machine.” Heading his “best buy" list is his 4890 Case 4-wheel drive tractor. “Plenty of power, easy to handle, comfortable, and has plenty of hydraulic capacity to handle my 12 and 14 cu. yd. scrapers.”
John Eisses, Stroud, Ont.: ‘This all happened with less than 500 hours on the tractor,’ says John, disap pointed with his 'tworst buy’ Case 2090 tractor, “It’s nice to handle but the pto clutch went out twice. Then the transmission had to be taken apart, it needed a new battery and the electrical system wouldn't work right. The dealer did give us a tractor to use when ours was in for repairs.” John likes his Honda ATC 110 allterrain bike and his 3,000 gal. Husky manure tank. ‘Even our 6-year-old can start itand driveit,” he says about the bike. “It’s handy to check fences, chase cows and check crops. The manure tank pulls easy and the orbit motor on the fan makes it real nice to spread with.”
Lorne Fuller, Calgary, Alta.: ‘I had just started to combine with my ptodriven pull-type combine when an internal shaft broke on the tractor. Exactly five weeks later, the dealer got the tractor fixed,” says Lorne, disappointed with his White 135 tractor. “The company representative, the dealer and service people all had different excuses for the delay. never brought the tractor home but traded it off for a Case 2390, which is my best buy. “It's a bitrough riding at times due to the short wheel base but the cab is quiet. Visibility is good except that it’s hard to see the drawbar for hookups. Has performed every job well.”
Jerome H. Zeimet, Bode, Iowa: “I bought it new and it's been a reliable machine with almost no trouble and little expense. Excellent service from the dealer,"’ says Jerome, pleased with his ‘tbest buy" 1816 Case skid loader.
Lynn Leichtnam, Presho, S. Dak: “The 3-pt. hitch on this tractor hasn't worked since we've owned it,” says Lynn, disappointed with his Case 2390 tractor. “‘When in the down position it won't pick itself up, It's been back to the dealer three times but is still not fixed.” Heading his ‘tbest buy” list is his Deere 1610 27-ft. field cultivator “Our old field cultivator’s wings would float out of the ground on uneven ground, so we had wheels installed on the entire length of the cultivator and it cured the problem.” Clarence McDougall, Mitchell, Ont. “It's run over 50,000 miles with only regular service and few repairs Pulls 60 market hogs in a gooseneck trailer and does almost all our trucking. Has a 4-speed manual transmission and a 351 engine converted to propane. Runs every day using very little oil,” says Clarence, pleased with his “best buy” 1980 Ford F250 pickup. He's also happy with his Nuhn liquid manure spreader from Nuhn Industries, Ltd., Sebringville, Ont, “Because we're dealing directly with the manfuacturer, service is never a hassle. We have used several of their spreaders and all have been well engineered and strongly built.” Will Ed Powell, Springfield, Tenn,: Will likes his Sure-Flame 2000 wood stove. “The stove is outside so there's no mess in our house, We have been on budget billing with our electric company for the last three years and have always owed them money in April when we settle up. This vear. after buying, our Sure Flame wood stove. we had a credit of $974 on our April billing. We did have to cut the wood, but this turned out to be a warming experience.”
Alan West, Darwin, Minn: ‘Alan's disappointed with his ‘D-Track, manufactured by Fabridyne, Litchfield, Minn. ‘“D-Track is supposed to attach to your grain drill to erase tractor tracks. First of all, it hardly makes a mark in the tractor tracks and, secondly, it doesn’t raise off the ground far enough on the end when you're turning. We contacted a company representative and he said he would help, That was a year ago and we haven't seen him yet!” On the “best buy” side, Alan likes his Case 2590 tractor. ‘The tractor is smooth running and very easy to drive. I've driven both International and Deere, and have found Case to be the easiest driving, best running tractor.”
Roger Kuntz, Grainfield, Kan: “My ‘worst buy’ is my Dixon lawn mower made in Coffeyville, Kans. The 8-hp. motor was too small for the cut of the mower. This engineering problem led to premature engine failure which was under warranty. Dixon said it wasn't their fault and Briggs and Stratton said the same thing. “My ‘best buy’ is my Case 2290 tractor. The comfort of the cab, easy to understand controls and its sheer dependability make it the best tractor for my father and me.”
Phillip Wagler, Partridge, Kan: An American Breeders Service representative, Philip says his own product is his “best buy”. ‘I use it on all 35 of my dairy cows as well as on my beef cows. get the use of the best genetics in the country and it does settle my cows. There isn’t a bull on the place except for one small calf.” Nick Kercheval, Shenandoah Jct., absolutely one of my best purchases,” says Nick. “I've found quite a few new products that have interested me and ideas for farm-built projects that I will use in the future, “Other ‘best buys’ include my new John Deere 6620 turbo hydrostatic combine. It’s a pleasure to operate. Its capacity is far greater than my old 6600 and the new unloading auger makes loading trucks a breeze. On the negative side, the 404 cu. in. turbo engine uses 1.6 gal. per acre with a 6-row head while the old 329 used .8 gal. per acre with the same head. “Lalso like my Echo 452 VL chainsaw with a 16-in. bar. The handle is vibration free and it starts easily.” Nick adds that ‘‘my used 1976 970 Case tractor was not a bad buy but I have had a frustrating problem with it. bought it with a bad power shift transmission and had to have the transmission rebuilt. Before rebuilding the transmission, the hydraulic brakes would actuate themselves when the motor was revved. The brake control block was replaced for $800, which cured the problem temporarily but now it’s doing it again. No one seems to know the answer. Otherwise, it's a fine tractor.”
K. Joe Kinnie, Julesburg, Colo: ‘I have never used a product that cost me so much,” says Joe, upset with Dual herbicide by Ciba-Geigy. ‘‘We were having trouble with foxtail on a couple hundred acres of corn ground. After considering many herbicides, we chose Dual for several reasons. 1. Ciba-Geigy claimed Dual will work by itself without another mixed-in herbicide. 2. Dual was said to work exceptionally well on foxtail. 3. We were told Dual would stay in the soil longer than competitive herbicides and thus would be there to take care of weeds that came on later in the season. “Unfortunately, we had foxtail emerge six weeks after planting. Choosing Dual cost us approximately $40,000 or, on the average, 70 to 80 bushels per acre. A Ciba-Geigy representative came out but gave us no satisfaction whatsoever. The fact remains that Dual did not perform. We applied the maximum rate and used the same sprayer as with our other herbicides. Comparing the Dual acres with Lasso and Atrazine acres, it looked as though we hadn't used any herbicide at all.” Oliver Noel, St, Lina, Alberta: ‘No more dependable than a Christmas toy from Asia,” says Oliver, disappointed with his Rockwell 10-in, band saw. “In thicknesses over one inch, the blade cannot be controlled at all. The blades break frequently and alignment cannot be kept permanent. Compared to other saws, it’s junk.” He's pleased, though, with his Makita 2030 12-in. planer/jointer. “We've used it for the past year to finish and shape rough lumber for shop use. It keeps its thickness setting perfect and the motor has been 100% trouble-free.” Oliver runs a new and used tractor parts shop and says he can pick the most popular older tractors by monitoring calls for parts, ‘‘Parts calls indicate to what extent these tractors are still being used. The three most popular at this time are: 1. Case 930. 2. International Harvester 706 and 806. 3. John Deere 4020.”
Don Anderson, Lewistown, Mont: “My worst buy ever was a Case 1370 2-wheel drive tractor,’ says Don. “When we bought the tractor the pto was not adjusted properly. The dealer worked on it five times in the first year and still the problem was not solved. Then, the dealer died and we didn’t get another for two years. Ex, “The entire pto clutch assembly burned out, dropping iron and pieces of clutch into the rear end.” cept when necessary we didn’t use the pto, but during spring seeding, it started to turn all the time. The new dealer told us to finish seeding and bring the tractor in, which we did. The entire pto clutch assembly had burned out, dropping iron and pieces of clutch into the rear end. One of these pieces went through the ring gear and pinion, chipping both. It also took out both final drives. Total repair bill was $15,000, “Since we had had problems with it in the first year, we felt Case should furnish us with the parts. But they said the tractor was too old at three years and had too many hours at 2,100. We traded the tractor and I'll never buy another Case product as long as I live unless the company changes its policies.”
Harold Waldron, Lacombe, Alberta: He's had trouble with his Case 2290 tractor. “The power train and motor are 100% but the hydraulic lines keep popping off ends. The heater hose broke in the cab and, in general, clamps on hoses were loose and bolts were not tight. The air conditioning lines were improperly installed and wore through. I've used five pails of transmission oil and one case of oil in the motor because of leaks last fall when I first got the tractor. Also, the battery cable shorted out, wrecking the alternator and one battery. Dealer service was good, but 11% to 2 days down every time you turn around is not so great.” Harold adds that he likes his XL 12 Homelite chain saw. ‘Runs good and has plenty of power for farm cutting.”’
Richard Templen, Solderis Grove, Wis: “Our Ford pickup jumps out of ‘park’ into reverse when running or with the motor shut off,"’ says Richard about his “worst buy”. “Ford now sends out stickers recommending that you set the emergency brake. We have had two close calls with this problem.” Richard's pleased with his Case 390 tractor. “It has an abundance of power, easy shifting because of the power shift, and good visibility from the cab along with a smooth ride. Our dealer is extremely reliable and fast on any and all service calls!"
Harry VanderPol, Alton, Iowa: “I'm not very proud of the transmission in my Ford F150 pickup,” says Harry about his “worst buy’, “I've always liked Ford pickups but I've just recently had to pay over $400 tc rebuild the transmission. The mechanic told me himself that this particular transmission was too ligh duty to be in a pickup. I guess nex time I'll get a % ton but then I'll be sacrificing ride and comfort.” Harry's had good luck with his 580-B Case backhoe tractor. ‘Have had no engine, converter, transmission, or rear end problems whatsoever in 3,000 hours,”’ says Harry. “Undoubtedly this is the best hoe in its class. Also, the dealership is tops in providing parts, service and leased equipment rentals.”
James Creighton, Cannington, Ontario: James lists his Massey Ferguson 510 combine as ‘‘worst buy”. “We had nothing but trouble with this machine. It worked fine in small grains but seemed to fall apart when we got into corn. Cost us a fortune in parts and repairs the four years we ran it,”’ he says. On the positive side, he’s pleased with his Case 1370 tractor and his New Holland 892 forage harvester. “We've driven this tractor 1400 hours and it’s never been in the shop. A pleasure to operate and it's easy on fuel. The harvester is a dream to work with. Has loads of capacity. Like the flip-up feed rolls and the newstyle corn head is a great improvement over our old machine.”
Dale Whitney, Watertown, S. Dak: “I am very pleased with my 2290 Case tractor. It has good power and is relatively easy on fuel for the horsepower it has. Dealer service has been great, too,” reports Dale. He says he’s had trouble with Firestone tires on his pickup. “I've had four of them develop bulges in two months. only had about 1,000 miles on them. Dealer adjustment was lousy.”
Ernest Hayl, Shandon, Calif: “Our 453 hillside IH combine was so poorly put together that we were broken down most of the time. The dealer and International people tried to blame all the breakdowns on operator neglect. Finally, we showed them that it had been assembled with poor alignment, which put the combine in a continuous strain. They made it better but it certainly cost us in downtime. “The International dealer in our area quit so we have had a hard time getting service and parts for our IH equipment. It shows that they don't seem to care for their customers. We have purchased IH equipment for over 40 years. We have three [H combines, four crawler tractors and a 4366 wheel tractor.” On the plus side, Ernest says he's pleased with his 30-ft. Marvin cultivator and 4890 Case tractor. ‘“The cultivator is lifted like a sulky rake so you can clean out the trash rapidly by dumping it. The construction is good so there's no problems breaking the frames, and so on. Our Case tractor does a super job. The dealer gives the best service possible.”
Real Deslauriers, Napierville, Quebec: “This tractor has power to spare,”’ says Real, happy with his Case 2090 tractor. ‘‘Handy controls, excellent cab, fuel economy, power shift transmission and it gets the best possible service from my local dealer.”
Carrol Wrinkle, Ontario, Ore: His two “best buys’ are his Ace Cultipacker and Case offset disk. ‘‘l bought the culti-packer from our local Ford dealer. It’s a good buy and works well in our heavy clay soil. Does well in clods and crust. Pulls either way — one side is regular and the other side grinds harder on clods. The Case disk really cuts, especially in straw and ground cover. It covers well, cuts deep and leaves little grooving in the field.”
D.H. Alexander, Brandon, Man: He likes his Wen electric chain saw. “ haven't used it much yet, but have had no trouble at all. It's very handy for cutting up firewood for the shop. Indoors it’s convenient as there are no exhaust fumes. “Also on the plus side, converted an old Case combine into a selfpropelled sprayer. It works quite well with two 200-gal. tanks and booms on it. Covers approximately 70 ft. with end nozzles. “I'm also pleased with my 18-ft. C.G.L.L. model 550 swather, Lays a real good swath and causes no trouble at all. The 200 Ford motor runs well and is easier on gas than the older model with the Wisconsin engine. The table is on a center pivot, does a good job of floating over stones and gullies, and is easy to control.”
Robert Born, Hazel, S.D: He's unhappy with his Case 2390 tractor. “The fuel tank leaked, hydraulic and power steerifig hose ends popped off, the manifold gasket blew out, an injector line broke, the cab was dusty and the wheels would lock up and slide if you stepped on the clutch without first moving the power shift to the number one position. Did have good power, however.” Robert also reports some problems with his TR 70 New Holland combine. “The shafts and gear boxes were too light. Brackets fell off due to poor welds.” : . Robert adds that his 9350 John Deere drills and 7000 Max-Emerge planter have proved to be good purchases. ‘‘After using the drills last season, I’ve had no problems. The three 10-ft. drills have a hydraulic transport that goes from field to road position, or vice versa, without unhitching the ‘tractor. I've used the corn planter three seasons with only one breakdown,” J.W. and
Jerry Wiford, Bellefontaine, Ohio: He’s pleased with a fold-up hydraulic kit he bought from Kelderman Man“Works perfect and makes transporting easy.” ufacturing in Oskaloosa, lowa, after installed it on a 12-row John Deere 30-in, row model cultivator. Instructions included were self-explanatory, making it easy to install. Works perfect and makes transporting easy. I've also recently purchased 2290 and 2590 Case tractors. Excellent hydraulics, cabs, fuel economy and power.”
Joe Berg, Stuttgart, Ark: He had trouble with his Massey Ferguson 2675 row crop tractor. ‘The engine was underpowered and never pulled its rated horsepower, One time it was 30 hp. short, The tractor spent two months in the shop but the problem was never corrected. It burned 9 gal. per hour pulling light loads, and smoked like it was burning coal. The local dealer tried everything he knew, but the factory representative didn’t show much interest.” On the plus side, Joe’s pleased with his Case 2090. “It has an improved cab and steers twice as easy as two of my older 70 series Case tractors. I like the shorter turning radius, and it's easy on fuel. Its slower rpm engine should increase engine life. Good dealer service.”
Ray Nauman, Norwalk, Wis: ‘The advertising claim was that it could handle anything but we found the manure had to have a water-like consistency or it couldn't handle it,” says Ray, who was disappointed when he tried, but did not purchase a BetterBilt liquid manure spreader with 3,200 gal. capacity. On the plus side, he’s happy with his Delaval 300 milking equipment. “The system really does a nice job and milking our herd of 100 cows takes about 2 hrs, time with 2 people and six units. Milk-out is very good and mastitis is kept at a minimum. People enjoy using it.” Oskar Heller, Scotia, N.Y,: His “best buys" are his 1090 Gehl mower conditioner and his International 550 manure spreader. ‘‘! used the mower-conditioner all last year and had no trouble at all. A great machine in cutting more than 150 acres. Dealer service was very good. used the spreader all winter with no trouble either. Dealer service is fair.” He’s unhappy with his DuraCraft Bench drill press. ‘'The first and second motors didn't work. The third motor works but it took 4 months to get that taken care of. Looks good but the workmanship is lousy,” he told “My worst buy nomination is a Carrier heat pump installed by Backwood Sheet Metal, of Ottawa, Ill. “The installer charged $47 to state that nothing was wrong.” The product does not maintain a comfortable room temperature. It cost page) about $4,000. Complaints to the company and the installer produced noresult. The installer charged $47 to check the unit and state that nothing was wrong. The Carrier Company did not respond to a letter of complaint.” On the plus side, Leonard likes his Case skid loader. ‘‘It’s the most useful and dependable piece of equipment on my farm. Have found 101 uses for it, with no problems after three years of service."
Curtis Wegner, Paynesville, Minn: He's happy with his Case 2290 and 990 tractors. ‘I’m having some hydraulic charge pump trouble on the 2290 but the dealer has given good service. The 990 has been good with no trouble except for a fuel leak in the return line which the dealer took care of right away. Real pleased with these tractors and the service." E. Scott Woodard, Jr., Ringgold, La.: ‘We've never had this kind of service on farm equipment or, for that matter, anything,’’ says Scott, pleased with the dealer followup on his Massey Ferguson 2705 tractor. “Other than an imperfection in the casting of the front axle, we're very satisfied.” His “worst buy’? nomination goes to his Gilmore-Tatge portable holding bin. “The cone sheets wouldn't fit together, Just a son of a gun to put together. It took three men four days to assemble the 9-ft. dia. 500 bushel portable bin.” Jim Jirava, Ogema, Minn,: ‘This baler has never baled 15 bales at any one time since it was new,"' Jim says about his Vermeer 605 Super C round baler. ‘The belts turn over every 4 to 5 bales, the slip clutch isn’t big enough for the machine, and any little gob of hay will plug it.” His ‘best buys" include an International 800 hinge plow and his 6-in. Vac-U-Vator pneumatic grain mover. “I've put just $12 into this plow in three years of plowing. Works well under any condition and follows varying ground contours. The Vac-UVator moves grain with ease and a minimum of trouble. Dealer service is good.”
Loy Kern, Morton, Tex: He likes his Case 2390 tractor, “It's been almost trouble-free in two crop years. Fuel consumption is minimal, employees love to drive it and it has the best draft control system I’ve ever had. Dealer is good, too.” Loy’s 1979 Ford LTD is his ‘‘worst buy”. “It’s made mostly of plastic and is hard to start. I've had nothing but trouble with the auto-temp control and transmission went out at 48,000 miles, Also, the electric door lock on the passenger side gives trouble constantly.”’
Harold Hawthorn, Foresters Falls, Ontario: ‘My ‘worst buy’ in 30 years of farming has been my new 1980 model 5540 Hesston big round “With the help of a good dealer and a good service man from Hesston, succeeded in getting my hay baled. However, wasn't told that this baler would not bale straw. “After every bale of hay, I have had to clean out loose hay that works up through belts and can't get out. The pickup will immediately selfdestruct if it picks up a handful of tough hay — we demolished it twice in 600 bales. The automatic twine tie is not dependable. If there isn't 1800 psi in the tractor hydraulics, the tailgate won't lift, which blew the pump on my Case 730 tractor and cost me $300 before even had the baler in the field, [had to run the new pump 300 lbs. over maximum before it would lift it. Obviously, the 5540 was not designed to function on all tractors. [ feel this Le ae baler should be recalled and redesigned. “My ‘best buy’ in recent years is a used John Deere combine. It just keeps on operating without problems. A pleasure to have it in the field,’ Harold concludes.
August Schueler, Bristow, lowa: “This attachment is a real money maker. Makes combine operating much easier and has almost eliminated the pushing of dirt while cutting close to the ground,” says August about his “best buy" Hiniker floating cutterbar. ‘I especially like the feature of using the sickle and guards on the original machine. Has been trouble-free.” On the minus side, he’s had trouble with his 1816 Case skid steer loader. “The basic machine is good but the main part — the 16-hp, Tecumseh engine — has been nothing but trouble. It vibrates bolts loose, which causes leaking gaskets. Have had broken axle hubs. The machine is terrible to work on. For example, the battery is buried under the platform. Dealer service is good but a terrible experience.”
Raymond Schoen, Ft. Smith, Ark: “Everything bought from John Deere in the seventies turned into lemons,"' says Raymond, nominating Deere’s 4400 combine, 4430 tractor, his field conditioner and a 20-ft. disc. “The combine would throw over too much grain. The 4430 tractor had bad hydraulics the dealer says can't be fixed. The conditioner filled with trash and we had to make major repairs the first season on the disc. I've traded everything except the tractor, which I plan to fix myself if it can be repaired.” Raymond is pleased, however, with Case's 2670 4-wheel drive tractor and his two TR 70 New Holland combines. “This is my third 2670. I have two at this time. It has plenty of power, is built to last and used less fuel and costs less to buy than the Deere 8640. Good dealer service, “I've cut 8000 acres with the two TR 70's and have had fantastic results from them, They may last until retire, he concludes,
Roger Kuhnert, Swanwick, IIL: Roger says he had trouble with Vicon's 15-ft. power harrow with crumbler roller. ‘A bearing went out almost every week, especially in the crumbler roller, The tine bars cracked while under warranty and were replaced by the dealer with a new style that cracked for the individual I sold it to. The company has since come out with another new style of bars. Dealer service was good and the power harrow did an excellent job in the field. just couldn't keep it there. “We've had good luck, though, with our Sears 250-amp AC/DC arc welder,’ Roger continues. “The infinitely variable amperage setting and stable arc are as good as more expensive industrial machines. also like my 930 Case diesel that has had no engine, clutch or final drive repairs in 13 years of use. It's one reason now have my third new Case tractor."
Everton Nevill, Tahoka, Tex: ‘My ‘best buy’ is a 1976 1370 Case tractor. This tractor has never been in the shop since purchased in 1977, is very economical, and easy to handle. My ‘worst buy’ has been a Tractor Supply Company 12-ton hydraulic jack. It won't lift and the slightest amount of water on the plunger causes the shaft to pit and leak oil.”
J.F. Leatherman, Healy, Kan: His “worst buy" nomination goes to a used John Deere 6600 combine. “The day after we bought it one rear wheel fell off, ruining the hub bearing and spindle. Then, the engine wouldn't run at full rpm. Every day there was some kind of breakdown. A year or so later the rear axle broke in half. You never know which bearing will go out as they are sealed, You run them until they give out. Dealer service is good but it's a continual hassle guessing which bearing we will have to purchase and replace." Walter Wittwer, Chowchilla, _ Calif.: ‘‘This combine does the cleanest job of any combine. Grain is clean enough to be able to use for seeding. Also, sends less out the back. Had some problems with combine sheaves, but excellent dealer backup,” says Walter about his New Holland TR 85 combine. “On the minus side, we've had trouble with our Case 4490 4-wheel drive tractor,” he adds. ‘‘It steers hard and I've had nothing but trouble with the steering system. It also does not have the power it should have for a 4-wheel drive. Hard starting also bugs me. Only good thing is the dealer stands behind it.”’
Reinhold Schmidt, Robinson, N. Dak: “Seven years ago I bought a 560 International equipped with an F-10 Farmhand loader, The tractor runs fine in summer but, when winter comes, look out. If it's damp, foggy, or cold, the carburetor ices up and for some reason, runs on four out of six cylinders. We recently had it overhauled and, as-it still did the same thing, had to take it back to the shop for more work. We finally purchased an 830 Case with loader.”
Craig Sorgenfrie, Winnebago, Minn: ‘The heater hangs outside and blows air into the building — cold air, that is,” says Craig, disappointed with his “L.B. White model 407 barn dryer. The dealer gave so-so service but finally felt 1 could do the repair myself after so many calls. Was only too happy to get rid of it for a heater that works. “My Case 1830 has added enjoyment to my chores and I find new jobs for it every day,’’ continues Craig. “It has the power and ease of a much bigger tractor, Very pleased with Case dealers and look for years of work from my machine,”
Clarence and Mark Hibbing, Paullina, Iowa: “I wish all dealers would stand behind their products as well," says Clarence, pleased with his “‘best buy'' Case 2290 tractor. “Dealer service and warranty have been excellent on the few problems we've had. The cab is quiet and comfortable and one of the biggest assets is the ease of access to daily service items.”
Gary W. Burns, Mt. Pleasant, Iowa: ‘My 1979 Case 2590 tractor has turned into a best buy, The only warranty work that had to be performed was a wiring harness which rubbed bare on the frame. At the 200-hr. check, it turned 206 hp on the dyno, Fuel consumption is also reasonable. Has lived up to all expectations.”
Ethelbert Heck, Liebenthal, Sask: Ethelbert's disappointed with the herbicide Lorox, which was used to control green foxtail. ‘We applied it as stated when the foxtail, or wild millet, was in the two-leaf stage, using 10 gal, of water peracre with it. It didn’t even stunt the foxtail but it sure reddened the durum. We blew $118 and probably three bushels per acre. “We like our 2470 Case 4-wheel drive tractor though,’’ continues Ethelbert. ‘Haven't had any trouble with it and it's extremely cheap on fuel. Just a pleasure to operate.”
William D. Schneider, McDavid, Fla: “It wouldn't level from the start. After the factory man had finished with it, it still wouldn't level," reports William who's disappointed with his John Deere 220 disk harrow. “We finally re-did the front gangs and got it to work fairly well. The bearings have been going out too soon, though, One goes out about every 150 acres disked.”’ On the plus side, William says his Case 2590 tractor has been a “best buy.” “It has good lugging power and uses only 8 to 9 gal. of fuel per hour despite its 188 hp. When it was in the shop, they offered to bring out another tractor for my use while it was down, but I didn’t need it. Excellent
Ron Baker, Mechanicsville, Iowa: “This chisel plow is one of the biggest disappointments ever bought, From day one it plugged up, things worked loose and it pulled like a 10-bottom plow,” says Ron about his Bush Hog 1450 Soil Hog. “‘It’s just 14-ft. wide but, behind a 200 hp.-plus tractor, you would swear it was 18 ft, You go 10 to 20 ft, and it plugs tight. I'm thoroughly disgusted with the company for putting it on the market.” Ron's happy, however, with his Case 1570 two-wheel drive tractor. “Runs perfect and the dealer has treated me with first class service, coming when I need him, In 142 years it has been to the shop once, besides regular checkups. They also came out to the farm twice for minor break-in problems.”
David Rietveld, Kouts, Ind: “We're disappointed in the performance of the air conditioner units in our Case 1070 and 1370 tractors. Takes two to three service calls a year to keep them going,"’ says David. linate “We're also disappointed in our local Case Company Store. Seems as though the personal touch is gone. Not enough dealer incentive." On the plus side, David nominates the following ‘‘best buys’’: Lilliston Tillager: ‘‘Once in the fall and once over again in the spring and we're ready to plant. Works great for incorporating, left-over corn trash to help bacteria growth and to put oxygen back in where it’s needed.” Long Nu-Way “Traveling Gun” irrigation system: ‘‘Works good in getting to the odd shapes and corners our center pivots miss. Excellent dealer assistance.” Erickson Skid Loader; ‘'The smoothest operating skid loader we've ever owned. Economical and efficient 4-cyl. engine design.” Duetz 6806 tractor: ‘Handles like a dream, not to mention a 50% reduction in fuel consumption with this air-cooled diesel.”
Paul R. Kittelson, Clark, S. Dak: “It tops a utility tractor in my book,” says Paul, pleased with his Case 990 tractor. “Bought it new in 1975 and had to replace a water pump at 700 hrs. But now, at 2,900 hrs., have had no further problems other than a leaking seal on the power steering. Economical on fuel and easy to start on the coldest winter mornings.” He's also well pleased with his Ford TN20 tractor; ‘‘Does everything I wanted — and more.”
Saul Pressman, Rosser, Manitoba: “Seems like we spent more time welding broken welds than we did cultivating. The welding was really amateurish,’ Saul reports about his Case heavy-duty 25-ft. cultivator. He's been pleased, though, with his 1977 Gleaner L2 combine with pickup, straight header, and sunflower attachment. ‘Does a super job in small grains, flax and sunflowers, with tremendous capacity. In 40 bu. wheat, using the 24-ft. header, we can travel 5 to 6 mph. Electronic controls in the cab are top-notch, along with monitors. Unfortunately, dealer service has not been on the same level.”
Herman Vincent, Jet, Okla: Herman nominates his 1070 Case tractor for “worst buy". “The clutch went outat 76 hours and it took nine weeks to get it fixed. The motor has had two major overhauls in less than 2,000 hrs. The main bearing burned both times, shutting off the flow of oil.’
David Leonhardt, Waskish, Minn: He's pleased with his Case 2470 4wheel drive tractor. ‘Has much more power than any other tractor we've had, and we like the 3-speed power shift. Operator comfort is outstanding; It’s just as quiet in the tractor as in my car. It would be nice, though, if it had a window on each side in the lower-side panels of the cab.” On the other hand, David's had trouble with his 12-ft. Northwest rotary tiller. ‘Does a good job of tilling and runs smooth. However, in our first season, we bent the main rotor shaft several times. A couple of other braces buckled, too, and had to reinforce them," says David, who raises wild rice and uses the tiller in paddies after harvest.
Rusmar Farms Inc., Roberts, Wis: They nominate their Valley irrigation ceater piv tasa “best buy". “Thisisa towable, 160 acre unit, We pull it across the road and reset it in just three hours. Tows easily. “We're also pleased with our 1370 Case tractor. Has good power, a quiet cab and service has been good. No problems."’ 120 FARM sHow “(~~
Francis J. Kukowski, Georgetown, Minn: “I bought a new 1370 Case tractor in Sept. 1974 and had more trouble with it in two years than with all other tractors put together in 10 years. In 1977, it was broken down a total of 10 weeks during the summer. Finally traded it off for a 4440 John Deere,” reports Francis. His ‘‘best buys" include his Deere 4440 tractor, and his Dahlman 39-ft. cultivator with liquid chemical attachment.
Richard Jagels, Buhl, Idaho: “The front of the pickup is great but the back is a joke,” says Richard about his 7-ft. Sund combine pickup. "Does a perfect job getting every bean onto the teeth, but the rubber flaps that feed beans to the combine auger suck the pods under and onto the ground, This is also the hardest turning pickup I've ever seen.”' On the plus side, Richard says that “Ray Stueckle’s combine book has been a big help to me. I've talked to Ray over the phone and been to one of his combine seminars. He's a smart man. set my 660 Case combine to his specifications and had only 3.1% cleanout on dry beans.” (The popular book, written by Ray Stueckle, R&H Machine, Box 1548, Caldwell, Idaho, was featured in FARM SHOW’s July-Aug., 1979 issue — Vol. 3, No, 4.)
Michael Martin, Logansport, Ind: “If you have trouble with machinery “If you have trouble with the dealer, don’t hesitate to call the company yourself.”’ or a dealer, don't be afraid to call the company yourself," advices Michael, who had trouble with his Case 1845 skid loader. ‘‘When I bought it, they told me it was their most trouble-free machine. They also said they would bring another one out for me to use if they ever had to take it in to work on it. That's never happened, despite the fact that my 1845 has been in the shop at least six times in four months. We had all kinds of trouble — a cracked block. bad hydraulic cylinders, bad carburetor, and bad hydraulic hoses and engine seals. “The dealer got so he didn't want to work on it, so 1 called the Case company myself. They said they'd talk to the dealer. Two days later, they called back and said it would be fixed in a week. The dealer was angry, but the company thanked me for calling. They said to call back if had more trouble.”
Melvin Frueh, Donnellson, Iowa: “It was alemon from the first hour on, with bolts falling out, the electrical system shorting out, power steering locking up and the transmission oil filter plugging every five hours," says Melvin about his ‘‘worst buy” 2390 Case tractor. “When they tore it down after 60 hours, they found that some wear washers in the rear end had been left out at the factory. The dealer was helpful in getting things right, but the tractor traded in — a 1370 — was nearly the same way. In 800 hours, it was down at least six times.”’ On the plus side, Melvin salutes his International 820 grain platform. “You can get nearer to the ground to get those low-standing soybean pods and make the field look as if you cut it with a lawn mower. Also, the cutting knife is faster so you can drive up to 4.5 mph and not strip the stems off. I've even been in a field with a John Deere row crop head and done just as good a job, yet can still use my head for small grain and drilled soybeans, which you can't with the Deere model." linate W. E. Cox, Temple, OkL: “The worst buy I ever made was a Krause chisel plow. The hitch was so weak had to have a welder weld it before had plowed 100 acres. That cost $50. Also broke two rock shaft clamps which cost $20 each. The bolts were too weak. The dealer wouldn't do anything unless the blockman approved, The blockman wouldn't approve so called the president of the company, who said he would see what he could do. I guess he couldn't do anything, at least he didn't. traded the thing off and got a John Deere.” On the plus side, Cox says “my best buys were two 6030 John Deere tractors."
Stanley J. Kondelik, Circle, Mont: _ “This tractor has been a pleasure to - operate and has had very few mechanical problems,"’ says Stanley about his 1570 Case tractor. “The dealer has also been good with service." On the minus side, he’s had trouble with his Massey Ferguson 750 combine. “Had less than 10 hours on the machine when the engine blew up, Dealer installed a new short block which was also faulty. The Perkins engine in this machine is one of the povrest have seen. Also, original equipment belts are very poor quality. The machine does work well when it isn't broken down, and the dealer has been good. He had another machine out in the field 31% hrs. after mine broke down,”
Bruce A. Schultz, Lapeer, Mich: ‘I nominate my Uni-Sheller system from New Idea as my best buy. Shells clean and fast and I can keep up with most conventional 6-row combines with my 4-row head." “My 14-ft. Case chisel plow is also excellent,”’ he adds. “Well built with tremendous trash clearance. Plugged just once in two seasons covering 900 acres of combine stubble, ‘My worst buy was the purchase of a used Allis-Chalmer’s 2300 disc. This machine is just too weak structurally for any field work. It looked like new but in less than 20 acres the hitch mount broke. After welding it, we watched it break within the next fifty acres. Finally. we made a new one three times as strong. Whole machine is under constant maintenance.”
Michael Gramm, Gridley, III: His “best buys” include his IH 830 chopper, his Case 444 garden tractor, and FARM SHOW. “The rubber gathering belts on the 830 chopper work beautifully and the rotary cut-off needs very little maintenance. “Case's garden tractor has large rear tires that give it great traction and a smooth ride. The hydraulic drive is wonderful. “And FARM SHOW," he adds, “is the best farm magazine I've ever seen, Keep it up.”
Richard Bradford, Chanute, Kan: He's disappointed with his Ford F-250 Ranger pickup. ‘‘My first problem was a brakeline that wasn’t tight. I lost the brake fluid two days after bought the pickup. Within the first month, both front disc brakes were loose. Gas mileage is around 8 miles per gallon. When complained about such low mileage they checked and I was told the choke was stuck. They freed it, but within a few days it stuck again and wouldn't budge. After several attempts, this still hasn't been resolved. I now have 11,000 miles on this pickup. Has more squeaks than my old one at 75,000 miles. I was told all these squeaks (in the brakes and steering) were common to this model and could not be repaired.” On the positive side, Richard is happy with his Case 4-wheel-drive tractor. ‘‘We chose this model because of the steering and have been completely satisfied. Drives just like a 2-wheel-drive and, after 750 hours, we've had no major problems and have lost no field time.”
Marvin Jontzi, AuGres, Mich: “Our best buy in the last year was Noland freeze guard hog waterers,” says Marvin. ‘‘They use less electricity than those we used before and 2._/—~ FARM SHOW 9 ‘Best’? and ‘‘Wor (ven at temperatures of 25° below zero and colder.” Larence F. Powers, Marissa, Ih: “A product that greatly concerns me is Attrex for corn,”’ says Lawrence, who's been using it for several years. "When we started using it, it killed all weeds and grasses at 1% Ibs. per acre. We work our ground the same now but use up to 2% lbs. per acre of the same material, and it’s just not as consistent. It seems to be a weaker product.” Lawrence adds that his “best buy" is a 1070 Case tractor he bought last year. “Case has always had good, sound engines and this is no exception, It's economical to run and the cab is clean and quiet. I have to keep the air conditioning on low because it really puts out, like the power shift transmission.”
Chuck Fredrick, Aurora, S. Dak: “My worst buy would have to be Ramrod wettable powder, It's the most irritating stuff in the world to your skin and eyes, and it plugged my sprayer about every 150 ft. It was supposed to mix up easily with water in the bag it came in but didn’t. For convenience, wouldn't use anything but a liquid herbicide.” “I'm extremely satisfied with the lugging power of this tractor and its economy," says Chuck about his Case 1570. “The large fuel tank lets you get some work done without running home every noon. The hydraulics and power shift transmission work great.”
Major Winter, Lake Providence, La: Heading his list of “best buys” is his 2670 4-wheel drive Case tractor. “It's got great power and pulls my 28-ft. disc at good speed. Except for a water pump, we've had no problem with it. When that happened, the dealer had it fixed in less than an hour.” He's disappointed, however, with his IH 1566 tractor. “This tractor has less than 1,000 hours on it and we've already put in two new transmissions, an axle, and an axle housing. The dealer paid for the first transmission but I paid for the second. Also, the tractor never seems to have enough gears and is either too slow or too fast.”
Terry Treadway, Hernando, Miss: “Does an excellent job of threshing beans. It's smooth running, quiet and has the best cab of any combine I ever rode in,” reports Terry about his TH 1440 axial flow combine. “‘The only complaints I] have are that the rear steering tires are of poor quality — “Just didn’t perform up to company claims in controlling weeds.” I've had too many flats — and the brakes are too small to be of any use. Good dealer service has solved all other problems.”’ On the negative side, Terry is disappointed with Prowl herbicide: “It just didn’t perform up to company claims in controlling weeds." Jim Greenmyer, Strium, N. Dak. His “best buy” is his 2670 Case 4-wheel-drive tractor. “It's got all the power and more than my dealer said it would. Like the 4-way steering and the good service on the few things that have gone wrong. “My worst buy was a 655 Massey Ferguson Hydro swather. Nothing but trouble from day one and poor dealer service." John Crabtree, Boise City, Okl.: He likes the rise in his 1979 Chevy C-30 crew cab pickup. ‘‘Once you get used to the wider turning radius, because of the longer wheelbase, it’s a pleasure to drive. Unusually comfortable for a 1-ton pickup — quiet and roomy, No complaints so far,”
Richard Arnsman, Payson, Ill.: “The hogs would have died before they walked through that crate to be sorted if I'd shut the hogs away from feed and water like the company recommended," says Richard about his Ostee Weigh-Krate. “The crate was supposed to sort out market-ready hogs but my hogs just wouldn't go through it.” On the plus side, Richard's well satisfied with his Case 2470 4-wheel-drive tractor. “It's got the power, traction and stability to pull heavy tillage implements over my rolling fields. Very maneuverable and easy to drive, and it has a good cab, You can actually hear the radio when the engine is running.”
Donald L. Kramer, Lewis, Ind: “Effectively replaces the moldboard plow,” says Don about his Hutchmaster 12-ft. “rolling plow” offset disc. “Really saved us last spring when rain kept all our other equipment out of fields. Does an excellent job of primary tillage. cutting through heavy growth, We pulled it at 6 mph with a 2470 Case tractor.” Donald’s also happy with his Kewannee 8-row folding rotary hoe, model 470. “Does a good clean job. Folds hydraulically.”
J. Lamar Norris, Elmore, Ala: He's disappointed with his Ford 9600 tractor. “The hydraulics are defective. Dealer has worked on it on two occasions and has since quit trying to fix it.” On the other hand, he's happy with his “best buy” Case 1370 tractor. “Always performs like it should. A good tractor,”
Thomas W. Rhodes, Horseheads, NY: “It's practically trouble-free. Speeds up silo filling and eliminates troublesome self-unloading silage wagons,” says Thomas about his best recent purchase — a Gehl Hydro-Tilt Dump Wagon, model 9000, "I'm also very pleased with my Knight LA-9 Little Auggie feeder wagon. Runs very well and maintenance is very easy on it.” Thomas is disappointed with his Case 970 tractor. “Most frustrating thing about these otherwise good tractors is the power shift, which is extremely difficult to shift between ranges, especially when cold. Our dealer gives excellent service, but when the shifting problem was checked, he said this was normal for that particular model.”
Dwight Strassheim, Oakville, Iowa: “My Superior 8-in., 57-ft. pto auger was a real bummer, The auger screw was not welded tight to the center shaft, which made it too big for the tube. After twisting the pto shaft off twice — $150 in repairs after 10 hours use — pulled the screw out of the tube and found the splice in the middle put in backwards and not welded, Also, the deflector at the top of the auger was factory bent the wrong direction, “After three weeks of telephone conversations with the district man and absolutely no help whatsoever, told him the next call was going to the company president at 7:00 that night. Thirty minutes later he called back and said they were shipping me a new screw — prepaid.” Dwight's best buy was a Deere 8434 tractor which “has power to spare, is easy to handle in tight spots and has excellent hydraulics. After owning IH tractors for 10 years now understand why J.D. costs more — they're worth more!" Dwight adds that his Case 1816 Uni-Loader is the “handiest thing on the farm and as easy to operate as a scoop shovel.”
Bob Delauter, Portland, Ind: Bob Delauter, Portland, Ind.: “Excellent truck. Lots of power with good heater and air conditioner. Full-time 4 wheel drive is nice but gas mileage is a little low — only 7 to 8 mph. Excellent snow removal vehicle when fitted with a Meyer snowblade and electronic-hydraulic controls,” says Bob of his "best buy" 3/4 ton GMC pickup. Commenting on his Case 1570 tractor, he notes that “the hydraulic pumps on the hydraulics went out, Dealer gave excellent service under warranty but was shocked that the gears failed after less than 100 hours of use."
Bill Kuntz, Park, Kan: Bill Kuntz, Park, Kan.: “A very good tractor for power and comfort,” ways Bill of his Case 1978 model 1570 tractor. He also compliments the dealer for coming out to repair some minor items. Bat also is well pleased with his Schueler feedwagon B-125. “Its a simple machine. No gear boxes. Cleans out the bottom real good and can be used as a grain wagon if needed. It is sealed real good. Haven't had a bit of trouble with it vet.” Also on his “best buy" list is Conklin's Rapid Roof, which he first read about in FARM SHOW. “Purchased a five gal. can of Rapid Roof for roofing a tin shed. It sure did seal excellent and is much cooler, It's an excellent product. Does not crack.”
Bill Knoff, Nashotah, Wis: Bill Knoff, Nashatah, Wis.: “Why must the farmer who pays for high priced machinery make all the modifications necessary to get if to run right? had so many problems finally got rid of it and went to 30 in rows,” says Bill of his “Burch twin row corn planter. Everything went wrong with it. Chains kept breaking with no slack adjustments on them, bushings were used instead of bearings. No monitor available until adapted one to work.” Bill is well pleased with his Glencoe Soil Saver. “It's a chisel plow with twisted shovels, and with cutting disks in front. Does an excellent job of saving time and no breakdowns. Built very rugged and needs “Why must the farmer make all the modifications to get it to run right?” 15 hp. per shank to doa good job, We go about 6% - 7 mph. Rocks are no problem with the disks in front — they give when encountering obstacles." Bill also nominates his New Holland 1400 diesel combine as a best buy. “Very well made. No problems in 3 years. Wouldn't be without the monitor. It does an excellent job of telling you when something is wrong. Only thing that could be improved is the service platform on the side of the machine it could be made wider, and some moving parts could be made more accessible for service work,” Bill adds that his Case 1070 and 1370 tractors “have excellent cabs — both for comfort and visibility and noise, Servicing is very easy. Never any problems with the power shift.”
Robert Noggle, Plainfield, Ill: Robert Noggle, Plainfield, IL: He notes that his 2470 Case “performs well but has a shrill whistle noise which we have had poor results in getting corrected, The noise is still there and the Company says they do not know what to do to correct il. It's very hard on the ears to listen to all day.” Robert adds that he is well pleased with a Port-Align precision drill guide which he purchased from Sears Roebuck tor $19.95. “This attachment fits in a “or 4 in. electric drill for drilling holes in exact center and straight through shafts or pipe. Has many uses and really worth the money.”
Larry Ruebush, Good Hope, Ill: Larry Ruebush, Good Hope, IIL: He says his Case 1816 Skid Steer loader is “one of the handiest things around my farm. It’s small enough to pet into very tight quarters to work and seems to be built heavy enough to stand up. I used it over 250 hours a year and have not had any welds break and have not bent or broke any iron,” He adds that the loader’s engine “leaves a lot to be desired. I'd like to see a small air cooled diesel engine, like a small Deutz, put in the 1816, Most air-cooled, one-cylinder gas engines just aren’t built for long, heavy use," says Larry who emphasizes that ‘the good points of the 1816 far outweigh my problems with it. would be lost without it.” Larry also passed along this buying tip: “I use Dupont’s Imron paint when I repaint trucks and equipment and it stays bright-looking even when it's dirty. It’s a polyurethane enamel and stands up to stains and scratches very well.”
Harry Tuma, Cut Bank, Mont: Harry Tuma, Cut Bank, Mont., of his new Steiger Turbo Tiger. “Our down time has been almost nil."’ Also high on Harry's ‘“‘best buy” list is a Harley rock picker, manufactured at Clarissa, Minn. He's disappointed, however, in Goodyear innertubes used in his Steiger tractor and a '76 Chevrolet pickup, pointing out that “the seams on the tubes are faulty. Even though they give an adjustment on the tubes, it doesn't begin to help pay for the chloride in the tires, or the service calls.” A new Case 2670 tractor earned a “best buy” vote from
Ron Spencer, Claremont, S. Dak: Ron Spencer, Claremont, S.Dak. We sent Ron and other randomly selected readers throughout the U.S, a survey questionnaire, asking them to “tell it like it is’ in nominating their ‘best’ and “worst" buys in the last 12 months or so. This special report is based on the responses we had received as this issue went to press. In addition to FARM SHOW, Ron who admits to being “strictly a John Deere man" — nominated a 1070 Case tractor as one of his “best” buys. ‘The reason bought the Case is that there weren't any John Deeres to purchase at the time, The Case is a very good tractor in regards to the cab and operating controls. The cab is very clean and quiet, and the air conditioning system is great. The tractor is easy to service and adjust,”” explains Ron, who also cited a few features he doesn’t like: **The rear wheels are a headache to change to different widths and the hydraulic system is difficult to hook up,” As in previous surveys, the importance of buying from a dependable dealer came through loud and clear: “It's been longer than 12 months inate sUYS but the lemon taste lingers on,” laments
Norman Culverwell, Craig, Colo: Norman Culverwell, Craig, Colo.. says his new Stieger Cougar is “the ultimate in a farm tractor. It’s comfortable, quiet and the caterpillar en“Tt’s been longer than 12 months but the lemon taste lingers on.” gine has a sufficient amount of power for any job.” Norman notes that he’s unhappy with his Allis Chalmers hillside combine which. he says, “gave problems from the minute it was put to work. The block man was called several times but never showed up. Most problems were related to the hydraulic system.” Norman also faults his Melroe plow, noting that “it broke up and wore out all over. The manufacturer claimed the dealer didn't have it adjusted properly. The dealer did several repairs and lots of welding on pieces that should have been replaced by the factory.” “Pearce Equipment at Clay City has taken good care of the service,”’ says Stanley Greathouse, Johnsonville, lll, who nominates his Case 1370 tractor as his “best” buy: “I've used this tractor one year and have been happy with performance and horsepower. It has a good cab, heater and air conditioner,” Dealers were directly responsible for “best” and “worst” buys nominated by William Allegar, Benton, Pa. He’s happy with the dealer he dealt with in buying his Ford 5000 tractor: “Had a few problems with it but the dealer was very cooperative. Fuel economy is very good and I'll be back for further business.” William is unhappy with after-the-sale service he got from the dealer who sold hima new IH 400 Cyclo air planter: “It developed a hydraulic oil leak when lifting the planter. Dealer didn’t want to know me after I paid cash for the machine.” That same make and model planter was one of the “best buys” Sackreiter Farm, St. Charles, Minn., has made: We planted over 300 acres of corn in a few short days and everything worked like a clock after a few minor adjustments," says Leon Sackreiter of their new IH 400 Cyclo 8-row air planter. ‘The Dickey-john monitor was well worth the extra investment.” Leon notes that a Gehl 2500 skid loader, purchased 8 months ago, “works very well when everything
G. O. Kalcinski, Camden, Mich: G. O. Kalcinski, Camden, Mich., says his “best buy’’ Case 1370 has given excellent fuel economy, averaging about 7 gal. per hour. He also likes its ease of handling, with all the controls on the right side of the seat. Two farmers who nominated Ford tractors as their “best" buy both cited fuel economy as a key reason: Says
Case 2290 tractor
7 Best Buys3 Worst BuysA 1979 Case 2290 tractor rates as John’s “worst buy”. “It has about 5,500 hours on it. The rear end went out twice, the powershift transmission has gone out three times, and the intermediate shaft in the transmission fell out. I’ve had to spend about $30,000 during the last eight years on repairs and on a new engine and fuel injection pump.”
Dale’s all-time “best buy” was a 1971 Case 970 demo tractor he purchased in 1974. “It still runs great and has approximately 13,000 hours on it. The original engine has never been touched.”
On the negative side, a 1979 Case 2290 was one of Dale’s worst buys ever. “The tractor is grossly overpowered for its transmission and rear end. We spent nearly $18,000 to fix it but it isn’t right.”
Earl’s happy with his 1975 Ford 6600 tractor. “We bought it equipped with an 8-split transmission with dual power which results in a total of 16 speeds. It’s an excellent tractor. It has about 7,000 hours on it and has required only minor repairs. We haven’t had to do anything to the drive train, engine, transmission, or hydraulics.
“Our 1982 Case 2290 tractor is neither a best nor a worst buy. We bought it new in 1982, but before it had even 3,000 hours it needed major transmission and rear end repairs. The park gear had some broken gears, and the crown gear and pinion gear had to be repaired. The total repair cost was $10,500. Since then it has been a good tractor.”
Gregory builds custom iron corrals and pens for farmers, ranchers, veterinarians, etc, and says his Miller Blue Star 2E portable DC welder is his “best buy”. “For three years during the fall and winter months I’ve used it 6 to 8 hours straight every day. It reminds me of a Timex watch - it just keeps on going. I’d buy another one. “I also like my Accu-Strike welding helmet with chin-activated lens. “My worst buy is my 1982 Case 2290 tractor. “The transmission never shifted properly. The tractor went through two rear ends in 1,800 hours even though I never over-pulled the tractor. After spending almost $11,000 on repairs I finally gave up on it. I replaced it with a Case-IH 7130 Magnum which is 10 times the tractor in every way.”
Ken Faber, Kippen, Ontario: “The company should have offered a factory rebate to compensate us for putting up with such a primitive transmission,” says Ken, unhappy owner of a 1984 Case 2290 2WD tractor. “Even with regular dealer service checks, the powershift transmission still shifts too hard, lifting the front wheels.”
Gregory Schmidt, Madison, Neb.: “This tractor was a lemon right from the start,” says Gregory, unhappy owner of a 1984 Case 2290 MFD tractor. “The first day the door handle broke, and the second day the drawbar broke during planting. Then the water pump and a gasket went out. At 600 “This tractor was a lemon right from the start.” hours the engine quit, Ithad a flat lobe on the camshaft, a cracked piston and all the valve inserts were completely burned out. The transmission contained some metal filings so big that they barely went through the drain hole. The warranty was a lemon in itself. The company wouldn't stand behind one cent of the engine overhaul or transmission work. With this kind of warranty, a person would think twice about buying another tractor and getting the same kind of treatment.”
Chuck Diel, Noble, Ill: His Gehl 125 grinder-mixer heads his “best buy” list. “It has required no repairs and little maintenance.” John F, Phelan, Perry, Iowa: “I bought my 1981 Case 2290 tractor used about a year ago with 1,700 hrs. on it. It’s my best buy because it uses no oil between changes and has plenty of power. I like the quiet cab. “Another best buy is my New Holland 479 hay conditioner that I bought years ago. It's been a faithful workhorse for many years with almost no down time. I'm also still using a 30-year-old New Holland 68 baler. New Holland builds equipment to last.”
Edward Pierce, Marengo, Ill.: “My 1983 Case 2290 and 1976 Case 1070 tractors are best buys. Both have been very reliable and relatively maintenance-free. We’ ve had to fix the air conditioner on the 1070 a few times and that’s about it. Both have plenty of power and we really like the power shift transmission and the comfortable cabs.” Charles F, Jackson, Lerna, Ill.: “The best buy I’ve ever made is our 1988 Cheyrolet 3/4-ton Silverado pickup. It has an excellent ride for a 4-WD and performs great. The only problem we’ ve had is that the contacts for the horn switch were positioned too close together. The vinyl cover“The contacts for the horn switch were too close together. Cold weather sets it off.” ing on the steering wheel would contract enough in cold weather to set off the horn. Itusually happened late at night or early in the morning. The dealer corrected the problem by spreading the contacts.”
Larry Dahl, Cogswell, N. Dak.: ‘In 3 seasons of use, my 1981 Case 2290 has never had a breakdown. It's needed only service and fuel. My 4-WD 1978 Case 2470 has over 1500 hrs. on it with only minor repairs."’ His “worst buy” is a Crown rotary rock picker, ‘We leased it with the option to buy. We sent it back at the end of the one year lease. It would only pick up small rocks and put more dirt than rocks into the box. It also had drive chain problems.” Delbert Ecklund, Minnetonka, Minn. He nominates a Fish carburetor installed on his 440 Dodge motor home as “worst buy’’. ‘It cost $212 for the carburetor and $102 for the adaptor. | had to rework all the throttle linkage, and automatic transmission shift-down linkage. I couldn't get a choke because I didn't buy from a dealer so I put an ether start on it for $80, It wouldn't start when cold and vapor locked when over 70°, If you set it for economy, it had no power and, when you adjusted it for power, it was a gas hog.
Gene S. Peters, Little Rock, lowa: “Our 1981 Case 2290 tractor has been as trouble-free as you could expect and is priced in a range that we can easily justify. Dealer support is great. We own two other Case tractors and have had similar good experience.” Albert Patterson, Sussex, New Brunswick: He's pleased with his Miller electric welder bought in 1978. “Works great and ‘it's the best money-maker on the farm because we make much of our own equipment,” Levon Schlenz, «Brockton, Mont.: Levon’s pleased with his Chrysler Sth Avenue. “It handles well, gets good gas mileage and has excellent workmanship.”
Case 1070 tractor
7 Best Buys1 Worst Buy“My Case 1070 has 1,200 problem-free hours.”
“A head gasket went bad on my 1970 Case 1070 tractor so I rebuilt the engine and turbocharged it at the same time. It cut fuel consumption in half and also resulted in a slight power boost.
“My 2007 Chevrolet Colorado pickup gets only 20 to 22 mpg compared to 28 mpg for my old Chevrolet S10. It starts hard in cold weather, and sensors keep going out. The S10 had about 350,000 miles on it and was a much better pickup than the Colorado. Maybe I just happened to buy a lemon?”
“I’ve had few problems with my 1977 Case 1070 tractor. It has a lot of power and is still going strong.
“Small gas-powered weed eaters often start hard and have problems with the string mechanism. But they cost only about $75, so after two or three years I throw them away and buy a new one.”
An early 1970’s Case 1070 tractor equipped with a powershift transmission and cab rates as John’s “best buy”. “I bought this tractor at an auction more than 15 years ago for $3,200. It has thousands of hours of heavy field work on it but has required only routine maintenance. It has gone through one set of tires, one set of batteries, an alternator, and a water pump. It still runs like new.”
Bruce nominates his 1983 Deere 4250 tractor as his “best buy”. “The Sound-Gard cab is quiet and comfortable and the engine runs good. It has 4,900 hours on it. I plan to have it overhauled at 5,000 hours. Some teeth have broken on the ring and pinion gear which could be due to operator error although I wonder if anyone else has had this problem. The tractor handles nice but uses more fuel than the Case 1070 that I owned previously. “I modified an Oliver 1610 front-end loader so I could mount it on my Deere 2940 tractor. It’s a light-duty loader so numerous cracks have developed in the frame and loader arms. It has a narrow bucket but that’s not much of a problem because I use a bale fork on it most of the time. It’ll get me by until I can afford a better loader.”
Pat Fenton, Richland Center, Wis.: “It'sa very dependable tractor and comfortable to operate,” says Pat, owner of a 1977 Case 1070 tractor with 5,000 hours on it. “Tt still doesn’t use any oil and I've spent only $3,000 on repairs and tires in 13 years.” Pat’s 1988 Case-IH 90 mower conditioner is also a “best buy”. “No repairs at all after two seasons of use. It'll cut at 8 to 9 mph.”
John Lang, Independence, Ore.: "Our 1972 Case 1070 tractor is our best buy ever. It has lots of power, is economical to operate, and it's quietand comfortable with wellplaced controls. A real pleasure to operate."
Wade Michaelis, Ness City, Kan.: Wade nominates his 1979 Buffalo 6row planter with slot shoe openers as ‘‘best buy’. “It places seed accurately and firmly in contact with the soil. Cover discs behind the press wheels cover seed with loose soil. Have never had to replant since using this planter. Coulters on gauge wheels slice through nearly anything, although heavy matted damp wheat straw does cause some choking problems. “Probably my best ‘buy’ ever is the Kansas Cooperative Extension Service. The wealth of research data, information and resources available through the Extension Service has done more to make my farm efficient than any machinery I could ever buy. “Another good buy is my 1977 Case 1070 tractor which bought after carefully studying a tractor test data sheet published by the Extension Service, The tractor is reliable, requires little maintenance and is economical to operate. The cab is quiet and comfortable on even the hottest days. I've had to replace the air conditioner compressor once and install a heavy-duty compressor clutch and belt idler pulley. expect many more years of service from this tractor.”
Case IH planter
7 Best Buys1 Worst BuyAlan’s impressed with the Selectro row shutoff he bought for his Case-IH planter (Selectro Co., Box 226, Avon, S. Dak. 57315). “I farm on contours so I have a lot of point rows, and with no-till I don’t cultivate so I have to be able to shut off the planter on point rows. The row shut-off lets me stop planting as I enter point rows. It saves seed and prevents overpopulation of the crop. I still cultivate end rows to eliminate double planting. “My 1980 Case 2290 tractor is my worst buy. The rear end and transmission each went out twice. All of the steel hydraulic lines broke and I lost 20 gallons of oil every time a line broke. Also, the fan went through the radiator. After the warranty expired I traded it in for a Deere 4440 tractor. The Case company spent over $6,000 on repairs during the warranty. They closed several stores which doesn’t help for service.”
Wilbur E. Smith, Erie, Mich.: “We're well-satisfied with Our Case-IH 25-ft. tandem disk. Itreplaced another Case-IH model that was 12 years old. It does an excellent job and disks level. “My son and I bought our first Deere lawn mower about 15 years ago. It was a 12 hp 212 model. We liked ita lot so we bought a second one five years later. Five years after that we wanted another one, but the company no longer made that model so we bought a 260 model. I don’t know if we'll get five years of service out of this one or not. It sure isn’t an improvement over the old models. We’ ve had problems with broken belts and with the transmission, We've never liked how it operates. I hope we can get a decent trade ona different mower next winter,”
Richard Schlaefli, Mankato, Kan.: Richard's satisfied with his 1992 Case-IH no-till air planter equipped with Acra Plant Trash Whippers. “No-till lets me make fewer trips through the field and saves time, fuel, and wear and tear on machinery. I like having to fill only one hopper. It’s simple to operate and easy to maintain.” Richard S. Gerhard, Quakertown, Penn.: “My worst buy ever was a Troy-Bilt 26-in. rototiller. It was poorly welded together and the transmission case was equipped with ano. 40 chain which was like a bicycle chain. It was always tearing or jumping off the cog wheel, and it took about a day to repair because the transmission case had about 40 bolts in it. I wanted the company to install a no. 50 chain but they refused so I bought a Wheel Horse rototiller. It has gears and a no. 60 chain. Works great.”
Wilbert Milleville, Niagara Falls, N.Y.: “We aren’t biased toward any particular brand of machinery but no matter the color of the machine, it must perform without much trouble,” says Wilbert. “We use Deere, Case-IH, and New Holland equipment side by side. We love our Deere 9500 combine and 347 and 348 balers, our two New Holland self-propelled hay stackers, and our Case-IH swing mower-conditioner. “Our 1990 Double Rake Hitch built by Ernest Steiner of Dalton, Ohio is a best buy, We own two of them and use them to pull four New Holland rakes, The hitch lets us make single windrows of any width or switch to double windrows right from the tractor seat. The maneuverability and rugged design make it an excellent buy.”
Charles Gruner, Coldwater, Mich.; “It shifts hard and sometimes it takes two or three tries to get the gear 1 want,” says Charles, who otherwise is pleased with his 1990 White 2-140 tractor, “It has excellent power, lugging ability, and fuel efficiency. My dealerand I discussed filling the 18.4 by 38 radial dual tires, but Lagreed to try it first without filling them to pull my 7-botiom, 18-in. land plow. It handled alright so I never have filled the tires. Itcost $9,000 less than trading for a Deere and $13,000 less than trading for a Case-IH. It has a good range of gears and there have been no oil leaks, fuel line leaks, or fuel gauge or light problems, etc. that have plagued me in the past. Even the air conditioner still works.
Richard Jennings, Tazewell, Tenn.: “My 1990 Chevrolet Silverado 2-WD shortbed pickup is a best buy. The 350 cu. in. V-8 fuel-injected engine has excellent power and has great fuel economy compared to my other three Chevrolet trucks. The sound system is excellent - my daughterloves it, Chevrolet has come into the 20th century with this truck. “My Case-IH 6-ft., 10-in. disc mower is the worst new product I've bought from “Chevrolet has come into the 20th century with this truck” Case-IH in several years. The shoes that carry the cutting discs are built from such poor quality metal that they wore out after cutting 40 acres. I replaced them with new shoes reinforced with T-1 steel, but then the discs cracked all to pieces due to the poor quality metal. understand that New Idea makes this mower for Case-IH. I’ ve worked more on this new mower than did on my old haybine.”
Charles Nelson, Plentywood, Mont.: “My 1985 Jeep Cherokee wagon gets 20 to 26 mpg. Goes right through mud and snow, Best & Woi ( “T pull my best buy Flexi Coil model 95 40-ft. harrow packer behind a field cultivator. It makes an excellent seedbed andconserves soil moisture. “My 1988GMC 1/2-tonpickupequipped witha 305 cu. in. V-8engineandautomatic transmission starts good in cold weather and averages 14 mpg on short drives. Even with 4-WD it rides smooth. It has almost 40,000 miles and the only cost so far has been for new alternator bearings.” On the “worst buy” side are Dane markers mounted on a 40-ft. Case-IH grain drill, “The markersare built too light which causes them to bend and break. I rebuilt them using larger square tubing which seemed tosolve the problem. “My Black & Decker 3/8-in. variable specd reversing drill never has worked well. Ithas good power but a very poor switch. It finally quit working altogether.”
Bradley Mills, Haviland, Ohio: A 1988 Case-IH front wheel drive 3394 tractor ratcsas Bradley's “best buy”. “It's gotplenty of power and has over 1,200 trouble-free hours. “My 1990 Case-IH 183 row crop cultivator is another best buy. It has a good heavy toolbar and does a good job of digging.”
Case 2390 tractor 5
5 Best Buys1 Worst Buy“I bought a used 1980 Case 2390 tractor 5 years ago with about 4,500 hours on it, and now it has more than 7,000 hours. It has required only routine maintenance.”
He’s disappointed with his 2008 Case IH JX80 front wheel assist tractor. “I’ve had numerous electrical and hydraulic problems with this tractor from day one, and it has been in the shop more than in the field. My dealer got tired of working on it.”
“My 1981 Case 2390 tractor has more than 6,500 hours on it and is my best buy. It hasn’t required any engine work and still pulls more than its rated horsepower.”
A 1980 Case 2390 tractor rates as Neil’s “worst buy”. “It has about 5,500 hours on it. There’s no problem with the engine - it has a lot of power. However, I’ve had to replace two hydraulic pumps, three power shift transmissions, and one torque limiter. More major repairs are being done to it right now. I’ve spent thousands of dollars. Another problem is that the differential lock clutch plates come ‘unglued’ regularly. It’s the worst piece of equipment I’ve ever owned.”
“My 1990Chrysler New Yorker car was my worst buy. I had to have the heads on the engine changed four times in the first 60,000 miles. The repair costs were covered by the warranty but it was still a nuisance.
“My best buy is my 1982 Case 2390 tractor. It has 2,800 hours on it with no problems and just keeps on running.”
Bruce Stauffer, Eudora, Ark.: ‘In 1% years I've put 1100 hrs. on it doing all types of work and it hasn't broke down. Has good power and is easy on fuel,’ says Bruce about his “best buy” 1981 Case 2390 tractor.
Calvin Schuk, Tatla Lake, B.C.: “They say this tractor is easy on fuel and agree. It's in the shop so often it doesn’t need much fuel,"’ says Jalvin, disappointed with his ‘worst buy” 1979 Belarus 820. ‘The failure list includes the starter, hydraulic pump, manifold heater, wiring, flywheel clutch, and the front brakes. The oil, fuel and coolant systems leak. Controls are poorly located.” On the plus side, ‘My best buy ever is my 1962 Massey Ferguson 35 tractor with a Perkins diesel engine. In 23 years this tractor has scraped pens, planted, harvested, fed livestock, and so on. All we've ever done is replace the tires, seat cushions, filters, a starter switch, and a head gasket. It's never let us down in over 15,000 hrs. of use.” Glenn Brandjord, Souris, N. Dak.: “Our 1979 Case 2390 tractor is a best buy. We've never had any downtime. The power shift transmission is very smooth, the tractor has lots of power, and the cab is extremely quiet and clean. One drawback is that the ride is a little rough. “Another best buy is our 1975 800 Versatile tractor. With over 4,500 hrs. of use, we have had virtually no downtime. It pulls as much now as me linate Soe it did when it was new. The 855 cu, in. Cummins engine is second to none.” Sam Wilson, Sentinel Butte, N. Dak.: “Our worst buy is a 214 Deere garden tractor. The motor vibrated so badly the coil kept breaking off and burning out. We bought it new but it was broken down most of the time. We traded it off for a 750 Deere tractor made in Japan and equipped with a tiller, backhoe, and a bucket. It's cheap, requires little maintenance, and the 3-cyl. diesel engine runs well. No problems.”
Case IH 7110 tractor
6 Best Buys0 Worst BuysFrank S. Wolcott, Bozeman, Mont.: “I have only 130 hours on my 1992 Case-IH 7110 tractor, but I’m well pleased with it. Four wheel drive makes farming our hills much easier.”
Guy McDiffett, Alma, Kan.: Guy’s pleased with his 1991 Case-IH 7110, 1992 Ford 1220, and 1992 Case-IH 5140 tractors. All have front wheel assist. “I’m satisfied with all of them. They have handy controls and perform well. I haven’thad any problems with any of them. “My Better Bilt liquid manure tankismy worst buy. Basically, the machine works fine but when a valve broke on the back, the company didn’t have the part. After two months I still don’t have the part. They say it’s on a ship from Italy. They wouldn't consider taking a valve off their assembly line. “I’ve also had problems with my 1992 Westendorf TA 45 front-end loader. My main complaint is with the quick tach mounting system. It has handles that you pull up to unhook the bucket. However, dirt and gravel can getin where the rods work up and down. I have to use a bar to pry the rods up sol can get the bucketoff. Also, the main frame broke during the first year.” Clark E. Zipse, Freeport, Ill; Clark's had good luck with his 1984 Deere 430 diesel tractor. He uses it with a 60-in, wide mower and a 48-in. wide blade. “It has plenty of power for mowing and pushing snow on our hills. No problems.”
Jonas Toews, Elma, Manitoba: "We're very pleased with our 1991 Case-IH 7110 tractor. We like the power shift transmission and good overall handling. The cab is very quiet, “Our Orthman guidance system is alsoa best buy. It keeps our cultivator right on the row and lets us cultivate much closer to crops.”
Donald Ziebell, Monee, Ill.: Jonas Toews, Elma, Manitoba: "We're very pleased with our 1991 Case-IH 7110 tractor. We like the power shift transmission and good overall handling. The cab is very quiet, “Our Orthman guidance system is alsoa best buy. It keeps our cultivator right on the row and lets us cultivate much closer to crops.”
Donald Lippelt, Geneseo, Ill.: Jonas Toews, Elma, Manitoba: "We're very pleased with our 1991 Case-IH 7110 tractor. We like the power shift transmission and good overall handling. The cab is very quiet, “Our Orthman guidance system is alsoa best buy. It keeps our cultivator right on the row and lets us cultivate much closer to crops.”
Charles Donham, Iowa City, Iowa: “The power shiftis great, visibility from the cab is excellent, and the electric sensor in the 3-pt. hitch is handier than a lever,” says Charles about his “best buy” Case-IH 7110 tractor. He says his Case-IH 4800 field cultivator is also a “best buy”. “It allows trash to flow through and with the addition of the harrow adjuster the harrow can be lowered to make it more aggressive and allow even more trash through.”
Case IH 7120 tractor
5 Best Buys1 Worst BuyCraig Griffieon, Ankeny, Iowa: “My Case-IH 7120 tractor has good visibility and power. I like the comfortable ride and ease of maintenance. No problems. I bought a 7140 three years earlier and haven't had much trouble with it either. “My New Idea 838 husking bed is my worst buy. The shafts at the end of the rolls and the chains are always breaking. The machine always seems to plug up in green seed com, It’s a joke.”
Duane Becktold, Blanket, Texas: “My 1992 Deere 4055 and 1991 Case-IH 7120 mfwd tractors are both best buys. Both are fuel efficient and handle well. Both have about 500 hours on them with few problems. It took longer to seat the valves on the Deere, but the dealer took care of the problem.”
Ronald Iles, Harpster, Ohio: “My 1990 Case-IH 7120 front wheel assist tractor has performed above and beyond my expectations. It’s fuel efficient and has great visibility, day and night. The power shift transmission and front wheel assist work great. “My 1986 Yocum Bros, sprayer can be used as an in-between unit or converted toa field sprayer in minutes. The wheels can be adjusted in and out or up and down. Excellent worksmanship (Yocum Bros., Cable, Ohio ph 513 653-8767).”
Kent Krause, Adams, Neb.: “Ithas good power and fuel economy and a quiet, comfortable cab with good visiblity,” says Kent, who has nevertheless had some problems with his 1988 Case-IH 7120 front wheel drive tractor. “It turns too wide at the end of the field for row crop work. There are two 12-volt plugs in the cab formonitors, butit’s hard to find a place to mount them without blocking my vision. The radio is poor. It's hard to tell what gear I’m in. There are no adjustable stops on the throttle or gear shift. Electric switches for the front wheel drive assist and rear axle differential lock are poorly located - they can be easily bumped.”
Geo. Moore, Castor, Alberta: “My 1991 Case-IH 7120 tractor isa best buy. Ithandles and steers well and has a lot of pulling power. I really like the 18-speed power shift transmission. It increases the tractor’s efficiency by 75%.”
Omer Laleman, Minneota, Minn.: “My Case-IH 7120 front wheel assist tractor has real lugging power and shifts smooth without clutching. do wish the cab had two doors to save walking.”
Case IH 1640 combine
5 Best Buys0 Worst BuysGene Wiemers, Melbourne, Iowa: Gene likes his 1991 Case-IH 1640 combine. "It's an excellent machine. Everything on it worked like it was supposed to. No problems at all. It's fuel efficient and easy to handle. I really like the new 1020 platform. I bought a reel enlargement kit from Reel Mfg, & Sales after reading aboutitin FARM SHOW (Reel Mfg. & Sales, Inc., Rt. 1, Box 132, Stonington, Ill. 62567). It increases reel size from the standard 42 in. dia. to 58, 60, or 62 in., alowing you to save 3 to 5 bu. of soybeans per acre. Kit consists of 15 1/2in, steel extension arms that bolt onto the existing reel arms and the mounting plate at the center of the reel.”
Richard Breneman, Parsons, Kan.: likes his 1991 Case-IH 1640 combine. "It's an excellent machine. Everything on it worked like it was supposed to. No problems at all. It's fuel efficient and easy to handle. I really like the new 1020 platform. I bought a reel enlargement kit from Reel Mfg, & Sales after reading aboutitin FARM SHOW (Reel Mfg. & Sales, Inc., Rt. 1, Box 132, Stonington, Ill. 62567). It increases reel size from the standard 42 in. dia. to 58, 60, or 62 in., alowing you to save 3 to 5 bu. of soybeans per acre. Kit consists of 15 1/2in, steel extension arms that bolt onto the existing reel arms and the mounting plate at the center of the reel.” DuWayne Hanson, Vienna, S. Dak.: “T’'m pleased with my 1991 Case-IH 4800 field cultivator. Depth control is easy to adjust. It does a level job and won't plug up in trash.”
Keith H. Lemke, Hardwick, Minn.: Keith likes his 1989 Case-IH 1640 combine. “It's easy to set. luse a 1020 bean head and 1063 corm head with it and they’re trouble-free. It has a quiet, clean cab with controls thatare easy to operate. Does a nice job of threshing grain. It can’t be beat for performance and is a super machine.”
Ken Pieper, Donnellson, Iowa: Ken's pleased with his Case-IH 1640 combine but says it could use a couple of improvements. “It does the job that it should and provides excellent grain quality. However, the bottom sieves should be easier to adjust and the unloading auger should have an alarm to tell when it’s running.”
Martin Greenleaf, Oxford, Penn.: Martin’s pleased with his 1989 Case-IH 1640 combine equipped with a Cummins engine, "It's quiet and easy to operate and all drives and maintenance items are easy to service. The engine is very fuel efficient." On the negative side, "Our Doanes Agchek IV computer accounting program and service contract is a worst buy. The program wasn't tested and contained problems which still haven't been corrected 10 months later. When I call in for customer support they're busy and call you back anywhere from a half hour to 2 days later. Who has the time to sit by the phone and wait?"
Case IH 1680 combine
5 Best Buys0 Worst BuysKeith D. Scott, Boissevain, Manitoba: “It's a beautiful machine to operate,” says Keith about his “best buy” 1990 Case-IH 1680 combine. “The engine has lots of power and the long chaffer sieve has enough separating capacity to handle the extra power. It’s a nice matchup.”
Herb Karst, Sunburst, Mont.: Herb’s satisfied with his 1990 Case-IH 1680 combine. “This is my fourth rotary combine and they’ ve all been easy to adjust and very dependable. “My worst buy is a 1989 GM Suburban diesel. It’s supposed to be identical to the 1985 model that I traded in, but the newer model is noisy, lacks power, and gets 5 mpg less than the 1985 model.”
Lavon Lampkin, Arkansas City, Ark.: “My 1989 Chevrolet S-10 pickup was a real lemon. At times it idled too high at 2,500 rpms, and I couldn't get it to slow down, The throwout bearing and rear end made constant noise. I made countless trips to the dealer who told me there was nothing he could do. traded it in on a 1990 Dodge pickup which works great. I think GM has lost pride in its products. “My Case-IH 1680 combine is a best buy. It cuts rice smooth and fast and does an excellent job of threshing and cleaning all crops. No problems at all.”
Don Stretesky, Julesburg, Colo.: Don likes his Case-IH 1680 rotary combine. “This is my third Axial Flow since 1979. I’m very pleased, especially with the good dealer service.” He’s also happy with his Orthman 6row bean cutter. “It never plugs up.”
Ronald Sanasack, Dumont, Minn.: “It's second to none for comfort and capacity,” says Ronald about his “best buy” 1990 Case-IH 1680 axial flow combine.
Case 1370 tractor
4 Best Buys0 Worst Buys“My absolute favorite tractor is my Case 1370 that I purchased new in 1977. Routine maintenance and tires are all it’s ever required. It’s never had a service call. It’s just a basic, fuel-efficient, quiet, nice-handling tractor.”
“I like my 1978 Case 1370 tractor.”
“I’ve had good luck with my Case 1370 tractor of which I’m the third owner. Only a few things on it have had to be fixed including the air conditioner, fuel gauge sending unit, and 3-pt. lift cable. It’s hard to believe, but the DEKA batteries in this tractor have been there since 1988.”
Arvene Doering, Hubbard, Iowa: He equipped his Case 1370 tractor with“ 100+” Power Additive made by Midwest Power Concepts, (P.O. Box 10, Radcliffe, Iowa 50230 ph 800 247-0504). “The system, which consists of an injector mounted on the rear side of the turbo charger, has cut fuel consumption about 10% and increased horsepower 10% for a very reasonable price.”
Case 1840 skid loader equipped
4 Best Buys0 Worst Buys“I like my 1994 Case 1840 skid loader equipped with a Cummins diesel engine. Day in and day out, this loader is dependable and trouble-free. It fits my farm perfectly. I bought it used in 2001 with about 6,000 hours on it, and now it’s pushing 9,000 hours.”
“My 1992 Case 1840 skid loader is a flawless machine. We’ve used it at least twice a day on our dairy farm for 15 years and now it has more than 7,000 hours on it. The biggest repair was replacement of the water pump at about 4,200 hours.”
Steve’s the satisfied owner of a 1999 Case 1840 skid loader. “It’s a dependable machine and makes life on our farm much easier. It has saved us a lot of labor.
“My Delaval/Harmony claw for milk units is my worst buy. It works slow and ruins the ends of the cow’s teats. If you want to go broke fast, this product will do it for you.”
Steve Korver, New Oxford, Penn.: Steve's had good luck with his 1989 Case 1840 skid stecr loader. “I use itevery day on my dairy and turkey farm. It starts easy in cold weather and speeds up chores and manure hauling. “My 1989 Deere 1360 disc mower conditioner is another best buy. It cuts down and tangled hay faster than the New Holland 495 disc mower it replaced,” William McGuire, Maroa, Ill.; “It's the best vehicle I’ve ever owned,” says William about his 1990 Dodge Ram 3/4-ton pickup equipped with a Cummins dicscl engine. “Starts good in all weather, gets good fuel mileage, and seems to have almost unlimited power. “My Deere 9500 combine is another best buy. It works perfectly, is easy to operate, and does the best job of harvesting I’ve ever seen.”
Case 870 tractor
4 Best Buys0 Worst Buys“We use our 1974 Case 870 tractor to pull our 12-ft. Case disk and it does an awesome job. We also use it to pull our Case IH RS 551 round baler.”
Steve’s happy with his 1971 Case 870 diesel tractor. “This tractor has performed admirably, whether I use it for haying work or with a pull-type combine. It has excellent power and is fuel efficient.”
Danny likes his 1970 Case 870 tractor equipped with a cab and 12-speed powershift transmission. “I bought this 75 hp tractor at an auction for $5,000. It had been used very little. Apparently it had been kept in a shed for 30 years as it still had the original tires and paint. After about 500 hours of hard plowing, disking, cutting corn silage, working with a hydraulic blade, and pulling planters and haying machinery I can definitely say it’s my best buy.”
Tony Dyck, Moosehorn, Manitoba: Tony purchased a used 1974 Case 870 diesel loader tractor in 1989 and says it’s a “best buy”. “It had 7,000 hours when I bought it. Italways starts in the winter even when it’s not plugged in. I use it to feed cattle and haul hay. It has about 75 hp and handles my front-end loader very well.”
Case 970 tractor
4 Best Buys0 Worst Buys“It’s built heavy and runs flawlessly. The most reliable tractor I’ve ever owned,” says Gared about his Case 970 tractor. “It’s a real work horse. I use it to cut and bale hay and everything else you can think of. I had a Case 1840 tractor that worked great, too, but it didn’t have as much power as this one.
“My ASV 4520 skid loader is a hard up with a 350 engine. I went from 13 mpg to 17 on a recent trip.
“The HydroStar was real easy to install. I’m a mechanic and have been looking at hydrogen units for some time. Previously, I put together one that was made from pvc pipe and had to be installed on the bumper, which was a pain because everybody asked about it. At one point it actually blew up when the water got too low. It didn’t hurt the truck; it just cracked the end pipes.”
Dale’s all-time “best buy” was a 1971 Case 970 demo tractor he purchased in 1974. “It still runs great and has approximately 13,000 hours on it. The original engine has never been touched.”
On the negative side, a 1979 Case 2290 was one of Dale’s worst buys ever. “The tractor is grossly overpowered for its transmission and rear end. We spent nearly $18,000 to fix it but it isn’t right.”
“It’s the best tractor I’ve ever owned,” says Victor, pleased with a 1976 Case 970 diesel he bought used 20 years ago. “It had 1,200 hours on it when I bought it and now has 6,800. It’s never been touched.”
He’s also pleased with his 1987 Ford pickup equipped with 6-cyl. engine and 4-speed transmission. “I put nearly 100,000 trouble-free miles on it. It still has plenty of power and runs great.”
James Burkholder, Wakarusa, Ind.: A 1992 Hanson center-drive silo unloader rates as James's “best buy”. “No problems. The only time we have to climb up the silo is for routine maintenance. It handles silage well and unloads fast. “We bought our 1980 Case 2590 tractor used last fall for heavy-duty field work and are well pleased with it. It has a lot of power and is nimble. “Our 1978 Case 970 tractor is also a best buy.”
Case IH 5100 grain drill
4 Best Buys0 Worst BuysJohn Miller, Howard City, Mich.: John says his M & W model 1815 rotary hoe is a “best buy”. “It does a beautiful job on small weeds incrusty ground and the 3-pt, hookup “The lawyers got the money and I got a patched-up engine.” is the best I’ve ever seen. All 3-pt. hookups should be built this way. “My 8-in.dia., 51-ft. long Westfield grain auger is a best buy. Works great. “My Case-IH 5100 grain drill is a pleasure to own. I like the large seed capacity. “My worst buy of all time is a Generac standby generator, It never worked and neither the factory nor the distributor would help.” RalphN. Smith, Mayport, Penn.; Ralph isn’t happy with white Onduline roofing sheets that he installed on the roof of his house, milkhouse, and silo, “The paint is peeling off leaving the old black material showing through, It looks very bad. The company has refused to do anything about the problem even though the roofing has a lifetime guarantee.”
Phillip Knapp, Marion, Ohio: Phillip's Case-IH 5100 soybean special drill heads his “best buy” list. “It does a good job of seed depth placement in varying conditions.” His Remlinger RTC-600 “does a good job of preparing seedbeds and incorporating soybean herbicides. “My International 1066 tractor and 1420 combine are very dependable. The tractor has 4,000 hours and the combine has 2,100 hours.”
Tommy Armstrong, Bloomfield, Ky.: “My 1989 Case-IH 5100 wheat drill meters seed out just right.”
Dennis Umbrell, Elizabethtown, Penn.: Dennis is pleased with his 1989 Case-IH 5100 soybean special grain drill. “It’s well built, easy to adjust, and plants seed accurately.”
Case IH 7110 Magnum tractor
4 Best Buys0 Worst BuysArnold Wipf, Hawley, Minn.: “My 1990 Case-IH 7110 Magnum and 1992 Case-IH 7130 Magnum tractors are both best buys. They're far more powerful than their horsepower ratings would indicate with temendous engine torque from 1,000 rpm's to full throttle under load. They handle nice, have quiet cabs, and are fuel efficient, “I've also had excellent luck with my Case-IH 6500 air hoe drill, It delivers excellent stands in any kind of seedbed without plugging up.”
Edwin M. Schaffner, Mondovi, Wis.: “My 1988 Case-IH 7110 Magnum tractor has a lot of power, excellent visibility, and a smooth powershift transmission. It has 800 hours. Case-IH has a good product here.”
Tom Probst, West Liberty, Iowa: Tom says a 1990 Case-IH 7110 Magnum tractor heads his “best buy” list. “I’m extremely pleased with it. It casily pulls a 22-ft. diskchisel plow without lugging down and regains rpm’s very quickly, The powershift transmission is smooth and has speeds where I need them. It’s a pleasure to operate. The cab is quiet and well designed with great visibility. “J uaded a Massey Ferguson 2745 tractor for the Magnum. I wish I had never seen that tractor. I could afford it when I bought it, but in the end the down time and repair costs made it too expensive to keep.” Marcel J. Dufault, Haywood, Manitoba: “I’m a crop adjuster so I travel a lot over rough fields and country roads. I find thatmy 1989 Chrysler Reliant K-car is abest buy. The 2.5-liter engine has plenty of power and is fuel efficient. It drives comfortably and handles well on unpaved country roads. The 5-speed manual transmission makes it nice for driving over fields. It has over 35,000 miles with no problems,”
Tom Probst, West Liberty, Iowa: A 1990 Case-IH 7110 Magnum tractor heads Tom’s “best buy” list. “I'm extremely pleased with it. It pulls a 22-ft. disk chisel plow without lugging down much and regains rpm’s very quickly. The powershift transmission is smooth and has speeds where you need them. It’s a pleasure to run. The cab is quiet and well designed and has great visibility.”
Case tractors
4 Best Buys0 Worst Buys“I bought a Dodge 2500 new in 2001. It has over 200,000 miles on it. I have only put brake pads on once. Otherwise, no problems.
“I have used Case tractors for over 40 years with no problems.”
“I bought my 1985 Case 2096 tractor used 5 years ago. It has a comfortable cab with a good view and is the most economical tractor I’ve ever owned. No problems.
“I’m not happy with the 2011 Battery Minder SCC015 solar charger I bought from Northern Tool. When the unit arrived it wouldn’t charge, so I returned it to the manufacturer at my expense. After 5 weeks and numerous phone calls I received a replacement. This charger is advertised to charge four 12-volt batteries, but I don’t think it could charge a watch battery.”
“All of our six International Harvester and 23 Case tractors have worked well over the years with no major problems. Three of them have more than 8,000 hours and are still used regularly on our dairy farm.
“Our 1992 Agco Allis 6680 2-WD tractor equipped with a cab is our worst buy. We purchased this tractor through a local dealer intending to use it mostly as a chore tractor. It had been factory reworked with low hours and some remaining warranty. It was the first tractor with a cab we had ever owned. It came with an electric heater which never worked more than one month at a time. The warranty covered two repairs to it, then we were on our own. The tractor wouldn’t start if the temperature got below 20 degrees. The dealer installed an ether assist, but it didn’t work because there wasn’t enough battery to turn it over. So I added a second one.
“This tractor had radial tires on it, and when pulling a manure spreader in snow it shook so bad, when the tires would spin that it broke a cab mount and also took out a brake line. The drawbar mounts would loosen or break off every couple of months. The front wheel bearings were insert-type ball bearings that would last only 300 to 400 hours before they broke, and then the wheel would fall off.
“The last straw was when an employee caught the front wheel on an obstacle 2 ft. in front of the parked tractor. It broke the bolster and the front part of the engine block. When we priced parts, we found that a bare block would have cost about $4,000 and complete engine $7,500, and neither was in the country. The dealer said he could weld it back together, but it ended up costing as much as a new engine and still leaked oil. We put it in an auction and walked away. It was the sor-riest excuse for a real tractor I’ve ever seen. It was cheaply built, noisy, and it couldn’t pull a hen off a nest.”
George Oliver, Fairview, Alberta: “I've owned other Case tractors before, but this one is the best yet,” says George about his 1991 Case-IH 9230 tractor. “It’s a pleasure to drive, is very easy on fuel, and has lots of power.”
Case 1175 tractor
3 Best Buys0 Worst Buys“The 1973 Case 1175 tractor I bought used with 2,100 hours on it in 1981 is my best buy. I put in one set of sleeves and pistons at about 3,000 hours. The tractor now has almost 11,000 hours on it and has been virtually trouble-free. It has a lot of power, is easy on fuel, and uses no oil. The only problem is there’s a big gap between fourth and fifth gear. There should be another gear in between for a more usable ground speed in the 5 1/2 mph range.”
“I bought my Case 1175 tractor used 10 years ago and it’s our best buy. It’s the only tractor we use to do all the haying and dirt work on our 120-acre farm. It has never let us down.”
Orvis Byklum, Grygla, Minn.: “My 1974 Case 1175 tractor has over 3,000 EE aT aE “The dealer did a good job repairing it. But what will happen next?” ae. an hours. I had to replace one throwoutbearing at 300 hours, Since then it has requiredonly routine maintenance, “My worst buy is my New Holland 855 round baler. The maindrivebeltbrokedown Editor’s Note: We received a lot of response to last issue’s “worst buy” report from Emily Coffey, Arvada, Colo., about her 1990 Ford-New Holland 276 bi-directional tractor that burned up. Jimmy Byers, Brinkley, Ark., sent us the photo above that shows a blown-out battery (on right in photo) in his 1992 Ford New Holland 946 340 hp. 4-WD, Byers thinks the battery hold-down brackets caused the blow-out. “If Emily had the same hold-down system on her tractor, and the batteries blew out, that could have caused her fire. The problem is that the brackets are positioned too close to the battery posts. They corroded and then shorted out. The end blew out of one battery. We had battery acid all over. Our dealer didn’t wantto repair the damage but after I threatened to sue, he did.” Ed Swanson at the Minnesota Department of Transportation, St. Paul, Minn., says one of the department's 1992 Ford New Holland 276’s burned up this fall. “Tt went up so fast, the operator barely had time to get off. We’re concerned because we own a number of these tractors. We don’t want anyone to get hurt and we don’t want to lose equipment.” Swanson says he thinks the fire started in the articulation area and may have been caused by an electrical problem, but no investigation has yet been carried out. Galen Travis, Burlington, Colo., who once had a fire beneath the cab on his 1985 Versatile 276, is convinced the fire problem is caused by friction between a drive shaft and crop residue that packs tightly into the area between the bottom of the cab and the frame of the tractor. “Trash packs in there so tight it’s difficult to get it out,” says Travis, who came up witha modification kit that raises the cab up a few inches (see story on page 29 in this issue).
Case 1825 skid loader
3 Best Buys0 Worst BuysBruce is pleased with his Case 1825 skid loader. “I bought this machine used with about 600 hours on it. I installed auxiliary remote hydraulic outlets and changed the front hookup system to make it work like the quick-tach systems found on newer skid loaders. We use it with a standard bucket as well as a grapple bucket and a backhoe attachment. We’ve put about 200 hours on this machine with no problems and use it for everything from loading manure to digging out tree stumps and cleaning brush. It’s a great machine.
“I bought a Chinese-made Run Master II go-cart on Ebay which was a waste of money. There were no written instructions. It came with a video tape in Chinese. After less than 50 hours of use this $1,500 go-cart is basically junked out. We had problems with everything. I’ve been told there’s no longer a parts distributor for this go-cart in the U.S. I don’t appreciate being scammed.”
“It’s a wonderful little machine,” reports Tom about his 1995 Case 1825 skid steer loader. “I bought it new with the single intent to clean out our cattle pens. It does a great job for that as well as for a thousand other jobs. I use it for something almost every day, all year long.”
“My 1994 Dodge 3/4-ton 4-WD pickup equipped with a Cummins diesel engine is my best buy. It has more power for pulling heavy loads than any other pickup I’ve owned. It gets a respectable 14 mpg when loaded and 24 mpg when empty. Pulling the same trailer, my old pickup got only 6 mpg loaded and 13 mpg empty. “My 1995 Honda TRX 300 2-WD ATV is absolutely trouble-free. I don’t know how I ever got along without it. “My Case 1825 skid steer loader, De Walt power tools, and International 5088 tractor are all best buys. However, I wish the filters on the skid steer loader were easier to access. ”My Dyna-Charge electric fence charger is a worst buy. The fencer module burned out every six months or so. I finally replaced it with a Red-Snap’r. It seems to be holding up well and also provides a stronger shock.”
Case 1896 tractor
3 Best Buys0 Worst Buys“I like my 1986 Case 1896 tractor which is equipped with a Case 90 front-end loader. It’s easy to operate and doesn’t require a lot of maintenance. My wife uses it to do loader work. My only complaints are that the transmission is hard to shift and the quick-tach loader is hard to take off.”
A used 1984 Case 1896 tractor equipped with a cab and front wheel assist heads Delbert’s “best buy” list. “I bought it two years ago with only 374 hours on it. I really like the front wheel assist. “I like my 1987 Case-IH 2294 tractor which has 3,000 hours on it. We’ve spent less than $50 for repairs. However, I wish it had front wheel assist. “I like my 1992 Case-IH 7150 tractor but I don’t like the Goodyear 20-8-42 radial tires. The 7150 can go only a few feet in mud before it gets stuck because the tires aren’t self-cleaning. I’ll never buy a new Goodyear tire again. “I’m well pleased with my 1989 Great Plains 20-ft. drill. It does a good job and is well-built. “I also like my 1991 New Holland TR96 combine but I wish it had a bigger unloading auger. It has an 8-row head and in 150 bu. per acre corn it’ll fill a 270 bu. tank in only seven minutes. However, it takes almost three minutes to unload it. “I’m pleased with a used Case 870 diesel tractor I bought. It has 80 hp and burned 4 gal. of fuel per hour before I put a turbocharger on it. Now it has 125 hp and uses less than 3 gallons of fuel per hour. We use it a lot with a pto-operated agitator at our slurry tank whenever we haul manure. “I also like my new Hutchinson 8-in. dia. hydraulic swing-around hopper auger. One man can easily move it from bin to bin.”
Eriel Iwamoto Lewiston, Utah: He’: pleased with his 1986 Case 1896 tractor. “T've used it for more than 300 hrs. now. It’s never had a service call or break down. It's very economical on fuel for its size and is easy to handle.” He’s not as happy with a Sears 26CC Weedwhacker. “I used it five or six time and it broke down. Cost of repair was about 2/3 the cost of a new one.”
Case 2394
3 Best Buys0 Worst BuysClem Weber, Fingal, N. Dak.: "My 1987 Dodge Dakota pickup rides like a car. Its powerful V-6 engine gets 16 to 19 miles per gallon. "Another best buy is my 1986 Case 2394 tractor. Handles like a dream, rides nice, and pulls a good load."
Daryl Beaudry, Elie, Manitoba: “We purchased our 1984 Case 2394 tractor new and we're very pleased with it. It's comfortable, powerful, and we have a good dealer. The salesmen back their product,” says Daryl about his “best buy”.
R.J. Rhea, Rome City, Ind.: He's had trouble with his 1985 Dodge 100 pickup. “From day one there was a vibration which, after dozens of trips back to the dealer, hasn't yet been corrected. The engine has never run tight — it jumps and jerks — and mileage is bad. At 13,000 miles it started using oil. In cold weather the auto transmission malfunctions.” Jim Haines, Bremen, Ind.; ‘‘It seems like it’s impossible to get seed and plates that match close enough to get it to plant accurately. Also, the little covering discs and the disc openers break and bend easily. I’m very disappointed with it,” says Jim about his “worst buy” International 800 plate type corn planter. Jim is pleased with his 1984 Case 2394 tractor. “It rides well thanks to the fine hydraulic seat. It has plenty of power so that you hardly ever need to shift down in the tough spots. We feel it's just as good as our old John Deere. Unfortunately we lost our dealer in the shuffle of the merged Case-IH company but our new dealer is doing a satisfactory job."
Case 2590
3 Best Buys0 Worst BuysJames Burkholder, Wakarusa, Ind.: A 1992 Hanson center-drive silo unloader rates as James's “best buy”. “No problems. The only time we have to climb up the silo is for routine maintenance. It handles silage well and unloads fast. “We bought our 1980 Case 2590 tractor used last fall for heavy-duty field work and are well pleased with it. It has a lot of power and is nimble. “Our 1978 Case 970 tractor is also a best buy.”
Gene Beard, Udall, Kan.: “We've had no problems at all with our 1983 Case 2590 tractor. It has an abundance of power and is comfortable to operate.”
Bill Garber, Delavan, Wis.: “I'd like to see a better seat. Also, the power steering works poorly at low rpm’s,” says Bill, otherwise satisfied with his 1983 Case 2590 tractor.
Case 430 skid loader
3 Best Buys0 Worst Buys“My 2008 Case 430 skid loader has a low profile that lets me get into low clearance buildings. The operator’s compartment is roomy for my long legs and arms. I use it to stack large round bales on end 3-high in my barn, and it’s very stable doing this. I bought it with the high-speed transport option, which reduces my travel time between farmsteads by half. I also use the foot throttle option a lot.”
“I’ve had good luck with my 2008 Case 430 skid loader. It’s equipped with a Cummins engine which I really like. This machine will do any chore I need it for. The induction for the skid loader’s heater was relocated so it doesn’t interfere with getting the machine into my barn. I added two side lights which really improved the lighting. The machine’s side windows are protected so if I have to work in brush I don’t have to worry about breaking them.
“The S.I. Precision Belt Meters I bought for my Great Plains 15-ft. bean drill are my worst buy. These belt meters are supposed to be a big improvement over fluted meters but they don’t work good. I paid more than $1,000 for them but have used them on only about 400 acres of beans. All the belts had to be replaced at my cost. The problem is that the plastic bearing-type guides don’t rotate, no matter how much graphite goes through the planter. Eventually the belt cage breaks off and then that row quits planting. The company should’ve used steel bearings instead of plastic ones. Also, it’s hard to get these belt meters to plant the correct amount of seed. Customer service has been terrible.”
“My 1964 Case 430 loader tractor is my best buy. I bought it used and am its third owner. This tractor has always been used on a dairy farm, but it wasn’t well cared for before I bought it. However, it has always worked well for me and is economical to operate.”
Case IH 1660 combine
3 Best Buys0 Worst BuysBill Jones, Liberal, Mo.: “My 1991 Case-IH 1660 combine is my best buy. It requires little maintenance and is comfortable to operate.”
Edward Huppert Jr.,Salem, Neb.: “It's one of the best buys I've made in a long time,” says Edward, pleased owner of a Case-IH 1660 combine. “It’s a wonderful machine to set and to operate. I’d never buy anything else. I had been a New Holland combine owner.” Ear! Hanson, Newfolden, Minn.: Earl's 1985 Chrysler New Yorker car has more than 100,000 miles. “It still runs and looks like new, making ita best buy. It’s equipped with a 2.2 liter turbocharged engine. “My 1982 Case 2390 tractor is also a best buy. I bought it used in 1986 with 875 hours. Now it has 1,875 hours with no problems.”
Larry Dosland, Calamus, Iowa: “Itused 16 quarts of oil during the first 100 hours of use,” says Larry about his 1990 Case-IH 1660 combine. “The dealer said he'd have to overhaul it this winter. If 1 wanted an overhauled combine I'd have kept my old one. At least it didn’t use oil. I like the specialty rotor for harvesting soybeans. No roping in green beans.” His “best buy” is a 1990 Orthman 680 grain cart, “Runs smooth and has ascale that works great for checking yields.”
Case IH 496 cushion gang disk
1 Best Buy2 Worst BuysMerle Spohr, Hancock, Minn.: Merle’s had trouble with his Case-IH 496 cushion gang disk. “The scrapers don’tmove with the gangs, which causes them to bend or break, The bolts that hold the gangs on break, bending the scraper bars. May also break the bearing holders, The manufacturer should stand behind its product, and when they develop an update kit to solve a problem they should contact us instead of expecting us to contact them.”
Harvey Wirkler, Farmersburg, Iowa: Harvey nominates his 1988 Case-IH 496 Flex-Wing disk as a “best buy”. “It works very well without plugging up and levels the land much better than the Krause model I had been using.” William Allan MacLean, Cornwall, Prince Edward Island: William nominates a Tanco autowrap silage bale wrapper as his “best buy”. “It’s well built and easy to use and adjust.”
Mark Herrold, Kewanna, Ind.:; “My 1987 Deere 450 Hydra Push manure spreader is a best buy. There’s no web to freeze or break, and it’s tightenough to haul liquid or solids.” On the negative side, “My Case-IH 496 25-ft. disk is a worst buy because the rock cushion springs break frequently.”
Case IH 5130 Maxxum tractor equipped
3 Best Buys0 Worst BuysGary Steckelberg, Nickerson, Neb.: Gary nominates his 1991 Case-IH 5130 Maxxum tractor equipped with front wheel drive assist as his “best buy”. “It always starts in cold weather and has a great cab with good all-around visibility. However, wish the remote hydraulic controls were clustered together. “My 1982 Deere 2940 tractor is my worst buy. It wouldn’t start after the temperature dropped to only 20 degrees. tried a new starter, arebuilt starter, a new-design starter, and then rewired the electrical system and cleaned all ground connections but nothing helped. Finally I sold the tractor with about 2,500 hours on it. [heard the new owneralso replaced the starter.”
David Parsell, Jerseyville, Ill.: “My best buy is my 1991 Case-IH 5130 Maxxum tractor that’s equipped with a power shift transmission and dual batteries. It origi“It's hard to believe that they could improve this tractor.” nally came with Goodyear Dyna Torque II tires, but the lugs on these tires are spaced far apart which caused the tires to wobble like a duck. I replaced them with Firestone tires. The factory shade canopy cost $800 so I bought a canopy from Femco (P.O, Box 1186, McPherson, Kan. 67460) for only $300 and mounted it on the foldable roll over protective structure. I mounted a CaseIH 510 loader on it, using a bucket from Farmer’s Factory (P.O. Box 122, Lee, Ill. 60530).”
Kurt Tewes, Frankfort, IL: “It’s the best tractor I've ever owned. I just can’t drive it enough,” reports Kurt, pleased with his 1990 Case-IH 5130 Maxxum tractor. “It’s very quiet and shifts smooth. It has good power and fuel economy and pulls my 14-ft. no-till drill with ease. Every farmer should own a Maxxum.”
Case IH 7120 Magnum tractor handles well
2 Best Buys1 Worst BuySteve Kutzler, Dodge Center, Minn: “My 1992 Case-IH 7120 Magnum tractor handles well and pulls all implements with exceptional fuel efficiency. The transmission shifts smooth and has a good range of speeds. The tractor has been trouble-free.”
Kenneth E. Smith, Middleburg, Penn.: Kenneth’s “best buy” is his 1991 Case-IH 7120 Magnum mfwd tractor. “This tractor is a joy to drive. Handles real well and has a range of speeds for every job. It's easy to service. No problems.”
Ralph Vonnahme, Breda, Iowa: Ralph’s had problems with his 1990 Case-IH 7120 Magnum tractor. “This tractor should have been painted yellow instead of red. In the first few months I had to rework the hydraulic system, air conditioner, replace all the sensors on the 3-pt., and adjust the powershift transmission, throttle, and fuel injection system. Last spring I overhauled the engine, installing new sleeves and pistons, rod and main bearings. I sent the head out for repair and installed a new camshaft, bearings and lifters. I also installed six new injectors and new fuel, oil, water, and air filters. I replaced the left hand inspection door and a door mechanism on the cab. I rebuilt all of the hydraulic detent assemblies, replaced two hydraulic cables, and readjusted the flow controls. I had to recharge the accumulators and replace the clutch return spring, left hand arm rest, radio, speakers, and fuel tank sender. After the air conditioning system had been recharged three times, I finally replaced the air conditioning compressor. “The 3-pt. sensors failed two more times and the center drawbar loosened up while hauling grain to town, All these problems occurred during about 18 months of use. inate Fortunately, the company paid for nearly all the repairs under warranty. I finally decided that since they liked fixing this lemon so much they might as well own it. I sold it back to them.”
Case skid steer loaders
3 Best Buys0 Worst BuysMarvin’s satisfied with his three Case skid steer loaders. They include two 1845 C models, one made in 1996 and the other in 2000; and a 1999 85 XT. “The 1845 C’s are used extremely hard but we’ve had very few problems with them. They’re both powered by Cummins diesel engines which are virtually trouble-free and start easily in cold weather. Their controls are precise and operator-friendly. The 85 XT works fast and is easy to operate. It will outload many larger end loaders. All these rigs are somewhat hard on tires, however.”
On the “worst buy” side, he lists his 1999 Deere 8100 MFWD tractor. “It’s a nice tractor with an excellent engine. But the armchair controls on this tractor are the pits. Because of their poor design, I’ve come close to getting into serious accidents. The transmission control makes it hard to distinguish between park and reverse. The rocker switches that operate the hydraulics are awful, and the instruments mounted on the side are hard to notice. This would be a nice tractor if it had the controls the company uses on its 7000 series tractors.”
“I bought a Case skid steer loader used in 1988. It still works good and we like it a lot. It has 5,500 hours on it and has required very little maintenance.”
Jeff Meyer, Saint Olaf, Iowa: “It starts well, is easy on fuel, and has plenty of power for its size,” says Jeff, pleased with his “best buy” 1978 International 886 tractor . “My International 666 has also been a good tractor, Only one repair in six years,” Jeff says his 1990 1818 Case skid steer loader is neither a best nor worst buy. “It runs well and does a good job, but shortly after I bought it the gas tank started to leak. It’s mounted in the frame and was poorly welded at the factory, The dealer rewelded it and repainted it.”
Case 1390 tractor equipped
2 Best Buys0 Worst BuysPat’s Case 1390 tractor equipped with a front-end loader heads his “best buy” list. “It’s the most powerful little tractor I’ve ever owned.
“My International 966 tractor, which I bought used five years ago, is a best buy. It’s equipped with a cab and air conditioning which makes it a pleasure to drive when baling hay.
“My 1989 Dodge Dakota pickup equipped with a 3.9 cu. in. 6-cyl. engine has 128,000 trouble-free miles on it and is a best buy. My 1986 Dodge Ram 250 equipped with a 360 cu. in. engine has 75,000 miles on it. I use it only to pull my livestock trailer and also for general work around my farm. The Dakota gets about 20 mpg while the Ram gets about 13 mpg. Both have been trouble-free.”
Elvin Latta, Cory, Ind.: “This is a terrible tractor,” says Elvin about his 1981 Case 1390, “Three months after I bought it the fuel tank split at the seams, I repaired it and it split again. This time the company gave me anew lank. Five years later the tank splitagain, and the fuel gauge fell into it. It’s hard to start below 45°, the steering arm is constantly loose, and the pto pilot bearing goes out every 6 months.” “My 1979 Case 2290 is the best tractor I've ever owned - 2,300 hours without a breakdown. Uses no oil and has plenty of power for tough pulls.” Elvin says his 1984 Deere 6620 is “a great combine - easy to maintain, plenty of power, and never seems to wear out. The cab is quiet and dust-free.”
Case 1490
0 Best Buys2 Worst BuysEugene Lewis, Corfu, N.Y.: His “worst buy” is a Case 1490 tractor with FWD. “I had many hours of downtime due to poor servicing and bad design, A dead battery at 20 hrs., clutch out of adjustment at 50 hrs., FWD wouldn’t engage at 75 hrs., gear shift is extremely hard to shift, broke a roll pin in the linkage and other parts, like the gear shift lever, broke, All problems were fixed atmy own expense, I just paid another $300 to have the gear shift worked on and it's sull hard to shift.”
Garnett Vickers, Mt. Olivet, Kty.: “The tractor's engine performs well but the power shift transmission is hard to shift between second and third gear. The dealer has taken the tractor in twice but can't fix it.” says Garnett about his “worst buy” 1981 Case 1490 tractor.
Case 1818 skid steer loader
2 Best Buys0 Worst BuysLarry Shepler, Reynoldsville, Penn.: “It operates smoothly and runs good, but is very clumsily built compared to the 1816 model it replaced,” says Larry about his 1988 Case 1818 skid steer loader. “There's too much overhang on the back so I can’t maneuver it in small places. It also needs a fuel gauge.” Larry’s Hesston 1010 Hydra Swing mower-conditioner is another “worst buy”. “The pivot tongue is the only good feature as it makes it easy to move the rig back and forth from field to repair shop. In one 1 3/4acre field I once broke 11 knives and three guards. It knocked out the cutterbar heads on a regular basis and they cost $70 each to replace. The conditioning rolls were there only to move hay off the cutterbar - they “The pivot tongue is the only good feature. Makes it easy to move the rig back and forth from field to repair shop.” couldn’ tcrimp arotten potato, Finally, stress cracks and bad bearings made us trade it for a New Holland 489 haybine which has caused very little trouble.” On the positive side, “My 1986 White 2 110 tractor runs smooth and is easy on fuel. Gear shifting isa little on the sticky side, but the powershift is smooth and easy to operate. The cab is very quiet and has better visibility than any other tractor I've ever driven. We like the cab so much that we’re looking for one for our White 2-85 tractor.” Larry’s 1989 Deere 430 round baler is another “best buy.” “It’s so easy to operate that the first bale I made with it looked as good as the last of the season, The monitor works great, but it’s difficult to set bale size because there’s no bale size indicator.”
Harlan Hartzahn, Greene, Iowa: “My 1988 Case 1818 skid steer loader is a best buy. I also have a 1969 Chevrolet C-50 truck with 540,000 miles that’s a best buy. On the negative side, “My 1988 Ford Ranger pickup isalemon. I boughtitslightly used from a local dealer and sent $100 to Ford for the warranty transfer. Then the problems began. I told Ford I'd paint it lemon yellow if they wouldn't fix it After 16 trips to Ford dealers (and many calls to the company), I traded it in for a 1990 Ford Ranger. It's had a few problems, but they seem to take care of it, It seems that if you take the pickup to anyone but the dealer you bought it from, you're out of luck. I've owned many Fords, but this one might be my last.”
Case 1845B skid steer loader
2 Best Buys0 Worst Buys“My Case 1845B skid steer loader, which I bought used in 1988, still works good. I like it a lot. It has about 5,500 hours on it and has required very little maintenance.”
“I bought a used Case 1845B skid steer loader in 1988. It still works good and we like it a lot. It has a total of about 5,500 hours on it and has required very little maintenance.”
Case 1845C skid loader
2 Best Buys0 Worst BuysBob nominates his 1994 Case 1845C skid loader as his “best buy”. “I bought it ‘very used’ five years ago from a dealer and am the third owner. I thought the machine was about worn out. However, I’m still using it every day and it runs great with no down time. It has gone through five sets of tires and a few hoses.
“I really like Sears Craftsman’s cordless tools but not the 19.2-volt batteries they use. The batteries don’t last long enough and are expensive to replace.”
Gary likes his Case 1845C skid steer loader. “We’ve done a lot of hard work with this machine, using it with a bucket, forks, and boom, but it never lets us down. It has plenty of power and always starts, even in the coldest weather.”
Case 2090
2 Best Buys0 Worst BuysLewis Novak, Belleville, Kan.: He's had trouble with his Allis Chalmers Gleaner L2 combine. “On anything but flat ground, the sieves overloaded so bad on One side or the other it's impossible to keep grain in the ‘machine at any speed. Finally, the dealer sent out a mechanic. After working on it for one hour, he had us traveling ¥2 mph and throwing over so much milo you could pick it up with a shovel. The dealer and one of the company reps we talked to were no help at all. We finally sold the machine for a $6,000 loss, plus the loss of the two machines we traded in on it. We replaced it with an 8-year old Deere 6600 that doesn't cut as fast but puts the grain in the bin.” Lewis names his Case 2090 and 2290 tractors as “best buys’. ‘We've owned five Case tractors since 1965 and we haven't had a bad one, They are all stingy on fuel. Our latest buy, the 2090, runs more than 24 hrs. on one tank of fuel while pulling a large round baler doing custom work. The factory recently installed an update package in the rear ends of both of the 90's and treated us real fair, We'll keep using Case equipment even if it is 75 miles to the dealer for service.”
David Branigan, Albin, Wyo.: David has four ‘‘best buys’. ‘Our Case 2090 tractor has 900 trouble-free hours, Our 1086 International tractor was bought used and we've had no trouble with it. It's a pleasure to drive, very clean, and as quiet as the Case. Both our diesel vehicles — a 1983 C10 Chevrolet 4-WD pickup and our 1983 Oldsmobile Regency 98 diesel — have been best buys. We get 26 mph on the pickup and 30 mpg on the car. We had a 1978 C10 diesel and a 1978 Regency diesel before that were also best buys. I’m sold on diesels.”
Case 220 lawn tractor
2 Best Buys0 Worst Buys“My worst buy is my 1998 Dodge Dakota pickup equipped with a 3.9-liter, V-6 engine. The bumpers rusted under the paint and bubbled out during the first year. That problem was repaired under warranty, but then the same problem happened again. The bolts snapped off on the exhaust manifold and also on both sides of the engine, and the upper ball joints wore out at about 30,000 miles. When I tried to change the spark plugs for the first time, the threads broke off in the engine. Now I’m just waiting for something else to go wrong. I never had any problems with the 1990 GM S15 pickup I owned previously. It was a much better vehicle.
“My Case 220 lawn tractor is my best buy. It’s probably more than 20 years old, but I’ve never had a problem with it. No other lawn tractor, including Deere models, compares to the quality of the old Case tractors.”
“My 1970 Case 220 lawn tractor is my best buy. My father bought it when I was in junior high school 30 years ago and now it has been handed down to me. It’s powered by a Kohler 10 hp engine which we’ve replaced or rebuilt twice in the past 20 years. We use this tractor to mow and plow snow. The hydraulic drive won’t give up and the mower deck is still in great condition. The only weak spot was the pto clutch, which we became really good at working on. We haven’t had a problem with it for years. This tractor is great for kids to learn to drive since the directional control is right on the steering column. Why doesn’t anyone sell a tractor this well built any more?”
On the “worst buy” side, he lists his Black and Decker 4-in. angle grinder. “I have a foundry/fab shop and really like how these grinders work. But they won’t last more than a few months.”
Case 2294 tractor
1 Best Buy1 Worst BuyThomas’s best buy is his 1985 Case 2294 tractor. “It’s comfortable to operate and controls are handy to get at. It’s easy to operate and has good vision from the cab. Maintenance on the engine and access to it are easy because of the tilting hood and removable access panels.
“My only complaint is that the 3-pt. hitch does not return to the same position or move up and down in direct relation to the lever movement in the cab. It’s nothing like my Deere utility tractor on which the 3-pt. is easily controlled to the 1/4 in.
“It has plenty of power, too, since the engine has been turned up to 145 hp, the maximum recommended for this engine.”
Thomas is also very satisfied with his 1980 Koyker K-5 front-end loader. “The only repairs have been to the bolts that attach the lift cylinders, hoses and seals.”
Fred Miller, Sherry, Wis.: “It’s a good starting tractor and I like the power shift transmission, but I wish it had more gears and shifted easier between gear ranges,” says Roger, who generally is satisfied with his 1985 Case 2294 4-WD tractor. On the “worst buy” side, “My Skil 3/8-in. electric hand drill is underpowered and gets hot when I use any bit wider than 1/4 in. dia, Also the chuck won’t stay tight unless I use a wrench on it.”
Case 2670
2 Best Buys0 Worst BuysDelbert Bauersachs, Pinckneyville, Ill.: “T’'m well satisfied with my 1992 Case-IH 7150 tractor. It has 790 hours on it with no problems. It’s easy to handle and the powershift transmission works great. It's fuel efficient and, with well over 215 hp, it'll outperform my Case 2670 in the field, I use itto pull my 1992 Case-TH 496 32-ft. disk in 9th or 10th gear. The disk does a good job leveling and is also a best buy. I also use it to pull my Great Plains 20-ft. no-till drill at 9 to 10 mph. The drill does a super job. planted 6,000 acres with it and had to replace only one press wheel bearing. “I sold my Deere 7000 8-row, 30-in. planter and bought a Kinze 8-row, 30-in. planter. It’s a best buy. The Deere planter was built too light and bearings were always going out. It went through over 25 bearings in three years. The Kinze planter is built heavier so I haven't had any bearing problems in three years. My only complaint is that it doesn’t plant as evenly as the Deere planter. “My 1987 Case-TH 2294 tractor has 2,450 hours with no major problems. And I think my 1991 New Holland TR96 combine is the best combine on the market. It shells up to 1,900 bu. of corn per hour.”
Randall Sinnwell, Nashua, lowa: “The tractor had bad power steering and shifted poorly to start with. Then, all the gears busted in the rear end and the transmission went out with less than 900 hrs. on the tractor,” says Randall, disappointed with his Case 2670 4-WD tractor. He's pleased with his “best buy” Deere 653A row crop head. ‘‘We thought at first, when we got the machine, that the knives would catch on rocks, But the guards keep rocks out of the knives, giving you a close, clean cut at field speeds of 4 to 5 mph.”
Case 440 skid loader
2 Best Buys0 Worst Buys“I love my 2006 Case 440 skid loader. It has a 2-speed transmission and ride control, which is great for making time. It’s also compact and has an 81 hp rating, which makes it drive like a bulldozer. I liked it so much that I bought a used 2007 model with about 1,100 hrs. on it, and it still runs like new. Case really had their ducks lined up in a row for this one.”
“My 1999 Case IH Maxxum MX 110 front wheel assist tractor is my best buy. This tractor is considerably heavier than its Deere counterparts, such as the Deere 7210 and 7220 models. The MX 110 is rated at only 95 hp but performs way beyond what I’d expect from a tractor its size. It’s also fuel efficient, averaging 3 1/2 gallons per hour depending on the load. It’s powered by a 5.9-liter Cummins turbocharged diesel which is very reliable. I’ve heard reports of similar models with 12,000 hours or more.
“I’d definitely buy another MX 110. The only major repairs so far have been to rebuild a planetary on a front wheel and a new hydraulic pump. The pump went out due to poor maintenance - the filter and fluid should have been changed sooner. We’re extremely pleased with this tractor.
“My 2006 Case 440 skid loader is also a best buy. It has a two-speed transmission which is handy and also fuel efficient, averaging 1.25 gallons per hour. We’ve had to make only minor repairs such as replacing a fan belt and a solenoid. It starts well in cold weather and has almost 1,800 hours on it.”
Case 4490
2 Best Buys0 Worst BuysJim likes his no-frills 1983 Case 4490. “We weren’t looking for anything fancy, just good economical horsepower and it hasn’t let us down on that score. It’s been trouble-free,” says Jim. “However, improved visibility would be a plus because you can’t see the drawbar from the cab. Also, it could use more gears in the transmission.”
Alfred Porubsky, Bannister, Mich.: “It's a good handling tractor with plenty of power and good fueleconomy,” says Alfred, who nevertheless has had problems with his 1980 Case 4490. “We've had trouble from day one with the hydraulic system and steering. The power shift went out after only ‘st Buys page) rotors turned. I hope the 4.3 liter engine that came out in 1988 runs better.” Grady likes his 1985 Snapper 30-in. cut, 8 hp lawn mower. “I have a big yard and mow abouta half mile along my road where I really should use a Bush Hog, It’s tough mowing and kind of rocky, but my Snapper always does the job, It has never broken down - only an occasional flat tire caused by a thorn.”
Case 4690
2 Best Buys0 Worst BuysLauren Steinle, Butterfield, Minn.: On the “best buy” side, Lauren nominates his 1983 Case 4690 4-WD tractor. “It has good power, a quiet cab, a tilt hood for easy service, and a four-way selective steering system for easy maneuvering.”
Leonard Armstrong, Aledo, Ill.: Leonard lists his 1982 Case 4690 and 2290 tractors and 1984 International 1440 combine as ‘best buys’’.’”’ Both tractors have been trouble-free and fuel economy is satisfactory. Combine does a good job threshing and has a large cleaning area.”
Case 4890 needs improving
2 Best Buys0 Worst BuysErnest says the hood on his Case 4890 needs improving. “It’s hard to get the hood up or down on a windy day. There’s no reason the manufacturer couldn’t install an electric or hydraulic lift system on the hood to make servicing it easier.”
Otherwise, he says he’s reasonably well satisfied with the tractor. “It has plenty of power and good hydraulics.”
Ron Baker, Mechanicsville, lowa: “We've never seen such a poor excuse for a planter, On a good day we could plant 50 acres and, on a bad day, just 5 to 10,” says Ron about his “worst buy” 8-row International 800 Early Riser planter. On the positive side, Ron's happy with his Case 4890 4-WD tractor. “It's given me one solid year of good hard work, I just sit back and let the tractor do the rest. When I’m done at night, it’s nice to get out without your ears ringing. Makes you feel like the day in the field was worth it.” Kent Carpenter, Cogswell, N. Dak.: “I've had this Wil-Rich chisel plow for two complete trouble-free seasons. The depth control is excellent for the application of anhydrous ammonia, thanks to the four walking tandems.”
Case 4-WD
0 Best Buys2 Worst BuysHerbert Halstead, Monroe, Ore.: “Our 1985 Chevrolet Sprint car with a 8-cyl. engine built by Suzuki gets 52 mph and has good acceleration. t has 12,000 trouble-free miles on it. My son liked it so well he bought one, too,” working components. Even after the shovels wear down. still get a good kill on weeds. nm “My worst buy is a 1975 2670 Case 4-WD tractor. After only 300 hrs. the engine started taking on water and antifreeze as a result of cavitation of the cylinder liners. After rebuilding the engine, had put no additional hours on it before I found out that it had a cracked head which the dealer should have checked when he had the engine torn down.”
Brian N. Lowe, Hoosier, Sask.: Brian nominates his 1600 series Deere 31-ft. cultivator made in 1972 as “best buy”. “It's very sturdy and does a great job. It transports easily, doesn’t pull heavily and has simple working components. Even after the shovels wear down. still get a good kill on weeds. nm “My worst buy is a 1975 2670 Case 4-WD tractor. After only 300 hrs. the engine started taking on water and antifreeze as a result of cavitation of the cylinder liners. After rebuilding the engine, had put no additional hours on it before I found out that it had a cracked head which the dealer should have checked when he had the engine torn down.”
Case 580 backhoe
2 Best Buys0 Worst Buys“I bought a used 1969 Case 580 backhoe in 1971, and it still runs great today. The engine hasn’t been worked on and is fuel efficient, using just 2 gal. per hour. I used this backhoe for a long time in my trenching business, and now I use it to feed big round bales on my farm. You never get stuck with a backhoe. I think every farmer should have one.”
“My best buy ever is my 1969 Case 580 loader backhoe, which I bought used 18 years ago. I paid $4,500 for it and it has paid for itself many times over. I’ve used it and abused it but it has required no major repairs. The loader is built strong and fast and accurate, and it works nice for handling manure or bales or even doing landscaping work. The weight of the hoe provides good stability. The best part is it still helps me make money.
“My Richie Thrifty King 100-head energy-free cattle waterer is my worst buy. The problem is the inserts for the lid bolts are mounted in such a way that the insulation gets saturated with water, making it useless. I’ve installed a 1,200-watt submersible heater and the riser pipe is heated, yet it still freezes. I plan to replace this unit with a regular fountain and burn this headache.”
Case 85 XT skid loader
2 Best Buys0 Worst Buys“As a dairyman, I haven’t bought much new equipment during the last couple of years due to the poor dairy economy. Besides, I honestly love my older equipment including my Deere 4430 tractor with about 17,000 hrs. on it, and my Case 85 XT skid loader with about 14,000 hrs. My Deere 8320 tractor and 1989 Mack R688 truck are also best buys.
“My 2015 Bobcat S770 skid loader isn’t a bad machine, but the local service department is impossible to work with. I can’t schedule repairs unless I have their road mechanic come out to the farm, which is very expensive. I’ll never buy another Bobcat.”
Marvin likes his 2005 and 1999 Case 85XT skid loaders. “They have a lot of hours on them but have been trouble-free. The Cummins engines in older Case skid loaders are the best ever built. These 85XT’s will easily keep pace with the much newer and larger Deere 332D skid loaders.
“We bought 2 new Deere skid loaders in 2012 – a 320D and a 332D. The 320D has required extensive work on the drivetrain – all 4 drive chains had to be replaced as well as both drive motors. The company honored the warranty, but now that it has expired I’m afraid the problems will continue. Case makes a much sturdier machine although I do like the heated cabs on the Deeres.”
Case 8850 swather
2 Best Buys0 Worst Buys“We use our Case 8850 swather to cut about 2,500 acres of hay per year and have had very few problems. It has about 3,200 hours on it, so we’re now starting to have a little trouble with the header.
“Our 1968 Deere 4020 tractor, which we bought used, is a best buy. We’ve had a frontend loader on it since 1974 and have used it to handle 1-ton bales all this time. The engine has about 9,100 hours.
“We have two International Harvester 1466 tractors, one 2-WD and one 4-WD, that together have 16,700 hours on them. They’ve done a lot of work but we’ve had to do quite a bit of repair work on them.”
“Our 1968 Deere 4020 tractor, which we bought used, is a best buy. We’ve had a front-end loader on it since 1974. We’ve used it to handle 1-ton bales all this time. The engine was overhauled at 8,900 hours.
“Our Case 1290 tractor, which we bought in 1986, has more than 10,000 hours on it yet the engine has never been overhauled. It’s a best buy. Our only problem was that the right final drive went out about 12 years ago.
“Our Case 8850 swather has about 2,800 hours on it. We use it to cut about 250 acres of hay per year with hardly any major breakdowns. We’ve custom cut a lot of acres with it.”
Case IH 1480 combine
1 Best Buy1 Worst BuyVincent A. Manhart, Palestine, Ill.: Vincent's “best buy” is his Great Plains 20-ft. no-till drill equipped with a center pivot hitch. “It’s one of the few pieces of machinery that I’ve taken to the field and started using without spending two or three days reworking or rebuilding. Company service is great. “My worst buy is Ausherman rotor bars that I installed on my Case-IH 1480 combine. The bars are made from a soft material, They will probably last only half as long as the original equipment and cost more to buy. I’m very disappointed in them.”
David Hemingway, Ellendale, Minn.: David nominates his Case-IH 1480 and 1680 combines as “best buys”. “They're both easy to maintain. The 1480 has 4,000 hours on it with very few problems. They’re good machines.” On the minus side, “My Case-IH 5400 minimum till drill is a worst buy. Wet soil sticks to the inside of the disc openers and causes them to plug up. “The heater and air conditioning controls on my Case-ITH 9100 tractor are inadequate. I either cook or freeze. “My 1989 Chevrolet 2500 pickup has had constant problems with the brakes, engine, and transmission. Ithas 45,000 miles and it seems like I'm always fixing it. It’s not tough enough.”
Case IH 485 tractor
2 Best Buys0 Worst BuysG.C. Glover, Lenoir, N.C.: He’s had good luck with his 1990 Case-IH 485 tractor. “I have 204 hours on it and have loved every minute, Everything about it has been perfect. “My 1982 Yazoo 16 hp 48-in. cut riding lawn mower is also a best buy. The only repairs I've made was to replace the belts, blades and bearings on the deck once.”
Francis Vereker, Liberty, Ind.: “I like its fuel economy and ease of handling,” says Francis, happy owner of a 1987 Case-IH 485 tractor and loader.
Case IH 5130 tractor
1 Best Buy1 Worst BuyMervin Lobdell, Lena, Il.: “Our 1990 Case-IH 5130 tractor is our worst buy. It runs well but we've had a lot of minor problems with malfunctioning computer switches. We could have solved all these problems if the company had offered a good service book with a trouble-shooting section in it. It took the mechanic many hours to find the problem.”
Leo Fox, Columbus, Wis.: “My 1990 Case-IH 5130 tractor shifts much better than the 96 and 94 series tractors. The powershift transmission is much faster than the one in my 1494, “The Case-IH 74L loader mounted on my 1494 tractor doesn’t fit good. The loader mounting bracket isn’t welded right, but neither the dealer or company will install a different bracket.”
Case IH 685 tractor equipped
2 Best Buys0 Worst BuysScott McKibbon, Mt. Hope, Ontario: Scott likes his “best buy” 1989 Case-IH 685 tractor equipped with a Case-IH 2250 quick-tach loader. “It has good power and ( 1<—a ~, — FARM SHOW e 13 Best & Wa ( excellent fuel economy, and the forwardreverse shuttle transmission works great for loader work. I wouldn't want to be without it. The quick-tach loader and bucket system work flawlessly. It takes less than 2 min. to change buckets or detach the loader. “My 1986 Case-IH 1190 mower-conditioner is also a best buy. The only part I've replaced is a belt idler pulley - not one broken section or guard, It cuts heavy alfalfa at 6 mph and does a good job. This machine has a rugged, simple design and is very reliable, like all of my Case-IH equipment. My previous International mowerconditioner served me well for 15 years. No doubt this one will last just as long.” On the “worst buy” side, “My 1987 Vicon RC 361 rake-tedder makes a nice fluffy windrow, but it’s impossible to set it so that it rakes the field clean. It’s tricky to adjust and very sensitive as to the combination of pto speed and ground speed. This machine is a disaster in the hands of an inexperienced operator. It’s totally useless ina long stubble crop like wheat straw. My old parallel bar rake equipped with basket tilt was a far superior tool.”
Leon Bradley, Union City, Mich.: “My 1989 Case-IH 685 utility tractor equipped with a Case-IH 255 loader is a best buy. Great fuel economy. “My 1990 Case-IH 4-row cultivator is a pleasure to use.”
Case IH 7140 tractor
2 Best Buys0 Worst BuysBill Wagoner, Emden, Ill..: Bill’s 1991 DMI field cultivator and spring tine harrow heads his “‘best buy” list. “The field cultivator goes through heavy residue without plugging. It’s built strong and should last for years. Every moveable part has a grease zerk on it. We had a couple of minor problems which the company solved promptly. It does a good job and stays in the ground.” Harvey R. Wirkler, Farmersburg, Towa: “It rides well and is fuel efficient,” runs like new,” says Harvey, pleased with his 1991 Ford F-1504-WD pickup equipped with a 302 cu. in. V-8 engine. “I’m well pleased with my 1991 Case-IH 7140 tractor and with my DMI wagons.”
Walter A. Hahn, Port Lavaca, Texas: “My 1992 Case-IH 7140 front wheel assist tractor is a pleasure to drive. It’s fuel efficient and has excellent lugging power and plenty of traction.”
Case IH 885 tractor equipped
2 Best Buys0 Worst BuysDavid B. Overbay, Chilhowie, Va.: “Our 1990 Case-IH 885 is a handy tractor. It has dual pto shafts, a large capacity hydraulic pump, mechanical frontwheeldrive, and good power. My only complaint is the toolbox. It easily gets filled with dirt and is totally useless. “Our Versatile 415 culti-mulcher is a great incorporation tool, It doubled ourcom yields on clay upland soil. “Our Deere 1360 mower conditioner is an extremely efficient machine that makes sicklebars obsolete. We can replace the ‘knives’ on the disc blades for about $12. The machine is heavy, though. On hillsides it’ ll cause our International 1966 tractor to slide.”
Michael Boucher, Brooks, Minn.: “It's casy on fucl and easy to service,” says Michael abouthis “best buy” 1989 Case-IH 885 tractor equipped with front wheel drive and a Dual 200 quick attach loader. “It has over 500 hours with no problems at all. The loader can be mounted or removed in less than five minutes.”
Case IH 900 12-row planter
1 Best Buy1 Worst BuyBill Fansler, Welch, Okla.: IS E Bill Fansler, Welch, Okla.: Bill’s had trouble with Martin row cleaners that he mounted on his 1993 Case-IH 900 12-row planter. “I used them to plant 120 acres of extremely cloddy soil. They performed well, but severely damaged the row units, cutting grooves into the frame. When I called the company, they said they had an update kitto solve the problem and that it would be available within a month. I don’tknow why they sold these row cleaners to me when the update kit was almost ready for sale. They must have known the row cleaners had damaged other planters. I feel restitution is in order.” Bill says his Case-IH 900 planter is his “best buy”. “I planted everything late this year. On most fields I just disked twice and planted so conditions were poor. However, I had perfect stands on all my fields.”
Lloyd Pope, Clear Lake, Iowa: Lloyd likes the spacing and seed depth control offered by his 1989 Case-IH 900 12-row, 30-in, corn planter, He says his 1989 Dixon lawn mower “cuts our mowing Lime in half.”
Case IH 9280 4-WD tractor equipped
2 Best Buys0 Worst BuysScott Hancock, Griffin, Ind.: “The air conditioner controls could be improved. I either freeze or burn up,” says Scott, who otherwise is pleased with his 1993 Case-IH 9280 4-WD tractor equipped with a 375 hp engine. “It uses less fuel than the 300 hp tractor we traded in,” On the “worst buy” side, Scott’s unhappy with his 1992 Great Plains 30-f1. folding no-till drill, “The biggest problem is that the end wheels aren’t in line with the transport wheels so when I turn at the end of the field, the end wheel drags up big piles of dirt. Also, after 2,500 acres both gearboxes seized up and broke. However, the company replaced them at no cost.” Albert Helm Jr., 40 Triple H Farms, Best & V ( hope the new model that will replace it will serve us as well as this one has.”
John Hall, Hereford, Texas: John's “best buy” is his 1991 Case-IH 92804-WD tractor made by Steiger. “It has greatly exceeded my expectations, The 30,5L-32 Tiger dual tires provide excellenttraction. It has unbelievable fuel economy, excellent serviceability because of the tilt hood, fast no-mess oil changes, an adjustable drawbar, and excellent climate control in the cab. I use it to pull my 80-ft. Friggstad chisel plow at 5.3 mph. I attach an 84-ft. EconoRod to the rear row of plow shanks and pull two 40-ft. CrustBuster grain drills when I planted my summer crop this year, butthat's pushing this tractor to the limit, I feel it could handle a 60-ft. version of this equipment with ease.” On the negative side, “My Snapper ET 200 edge trimmer equipped witha Briggs & Stratton engine is a worst buy. The engine doesn't have any power atall. When I lower the edger blade to the ground it dies immediately, regardless of how careful or slowly Ilower the blade. It’s absolutely worthless.”
Case IH Magnum 7120 tractor
2 Best Buys0 Worst BuysGlen Odle, Stockton, Kan.: “My best buy is my 1991 Chevrolet Caprice. It gets 27 mpg and rides good. Only one minor repair in 21,000 miles. “My 1988 Case-IH Magnum 7120 tractor is neither a best nor a worst buy. It has good power and is economical to run, “It breaks every time we use it and then we have to wait six weeks for parts.” However, I’ve had to pay for a few repairs that I think the company should have covered.
Richard Noel, Highgate Center, VL: “It has plenty of power, comfort, and economy,” reports Richard, pleased with his 1989 Case-IH Magnum 7120 tractor. “It'll pull a 7-shank subsoiler 12 to 14 in. deep at 6 mph using 6 gal. per hour, The dealer and company have fixed all problems. “My Deere 1360 mower conditioner is another best buy. I’ ve used itto mow 300 of alfalfa, timothy, and reed canary grass. No breakdowns.”
Case IH Magnum 7130 equipped
2 Best Buys0 Worst BuysGene Wiemers, Melbourne, Iowa: “My 1990 Case-IH Magnum 7130 equipped with front wheel drive is a best buy. It’s very comfortable to operate, has a nice transmission, a comfortable seat, and excellent visibility. Front wheel assist really makes a difference. The 3-pt. hitch has a lot of lift.”
James Wish, Bellefontaine, Ohio: James is the satisfied owner of a 1990 Case-IH Magnum 7130 tractor. “It offers great shifting, visibility, comfort, ride, performance, and fuel economy. Case-IH has finally made a tractor that competes with Deere.” James has had problems with Acra-Plant shoes. on his Case-IH 900 planter. “The shoes are supposed to outlast Case-IH shoes, but they don’t even come close. Each set lasts only 300 to 400 acres which is far less than the company’s claim.”
Case IH Maxxum 5120 tractor equipped
1 Best Buy1 Worst BuyArtThomas, Stryker, Ohio: Art’s happy with his 1990 Case-IH Maxxum 5120 tractor equipped with a cab and powershift “This tractor is so noisy that ear plugs should be offered as standard equipment.” transmission, “It does what it’s supposed to do. It had a few minor problems at first, but the dealer took care of them right away. My only complaint is that some of the controls aren’t very handy to use.” Steven M. Owen, Henry, S. Dak.: “My 1979 GM pickup has 241,000 miles but the body and cab are still solid.”
Tim Schultz, Clintonville, Wis.: “My best buy of all time is my silage bagging equipment. ( /y/ .2?. FARM CHOW - 42 Best & W ( I started with a Silopress XPIII (Silopress, 1915 Floyd Blvd., Box 988, Sioux City, Iowa 51102) and now also use a Uni-press. Both systems make it easy to make excellent quality feed for my 65 dairy cows. They’ve allowed me to increase production and profit per acre from forage while reducing the amount! spend on purchased feed. I had been using cement top-unloading silos and Harvestores, but now they stand empty and unused - I can’t afford to use them. “My 1990 KnightReel Augie 2375 TMR pull-type mixer is also a best buy. It lets me feed all my milk cows once a day in about 45 min, and has allowed me to maintain a 20,000-Ib. herd average while cutting purchased feed costs by 40 to 50%. The TMR mixer and silage bagging systems together have greatly increased my profitability. I'll never go back to my old system. “My 1991 Vermeer 504 Super I baler performed just like I expected and makes nice tight bales. The dealer spent plenty of time with me to make sure I knew how to use it I'm completely satisfied. “My Landoll Tilloll implement provides true one-pass spring tillage. Really saves time and fuel. “My Deere 1460 disc mower-conditioner is a best buy. My wife can use it to cut hay at 7 to 8 mph without plugging it up. I’ve tried my hardest to plug it up, but I can’t. If it lasts as long as it’s supposed to, it'll eam ‘best buy’ status. “My worst buy was a 1990 Case-IH Maxxum 5120 tractor. It caused me lots of grief before I traded it in on a Deere. In “If it lasts as long as it's supposed to, it'll earn 'best buy' status.” fairness to Case-IH, it was one of the first models built and I understand that most of my problems have been corrected in later models or by recalls. However, I still feel it has too much electronic equipment for a farm tractor. The 3-pt. took too long to lower for a job like cultivating and trim pieces kept falling off. In cold weather the engine would start fine, but the tractor wouldn't move. The clutch works off electric switches somehow. The dealer bent over backwards to solve the problem but had no luck. I’d recommend the dealer to anyone, but a Maxxum only to my enemies,”
Case backhoe
2 Best Buys0 Worst Buys“My son mounted a Case backhoe on a 4-wheel trailer that we had been using to haul our skid steer loader. All we do is hook it up to our International Harvester 1066 tractor and it’s ready to go. We use it to install water lines. Works fine and has saved us many hours of hard work and expense.”
“I’ve owned three Case backhoes in the last 20 years and they’ve all been best buys. I sold my 1980 580 C model when it had about 6,800 hours on it. It required very little maintenance. When I sold it I actually got $2,000 more than I had paid for it. My 1994 580 SK model had about 5,000 hours on it when I traded it off for a new 2000 590 Super L, which is the best one I’ve had. It has a lot of power and comfort.”
Case 0580 K loader
1 Best Buy0 Worst Buys“I like my Case 0580 K loader and backhoe. It has never been back to the dealer and hasn’t needed any major repairs.
“My 1999 Mercury Grand Marquis is my worst buy. It burned a lot of oil from the day I bought it. I was told this problem would get better once the engine got some miles on it. Later, the dealer told me this engine is supposed to use about one quart of oil every 900 miles. However, when I got rid of the car at 22,000 miles it was using three quarts of oil about every 1,000 miles. I paid $30,000 for this car and traded it after I had used it for only 26 months. The trade-in value was only $8,500.”
Case 1030
1 Best Buy0 Worst BuysLance A. Sidone, Boswell, Penn.: “Those 28, 30 and 34-in. tires just don’t cut it, especially on hard pulls and hilly ground. Stability and traction very poor,” reports Lance, disappointed with his 300 International utility tractor. As “best buy”, he nominates his Case 1030 tractor. “‘We bought it used. Has unbelievable pulling power and torque.”
Case 110 tractor equipped
1 Best Buy0 Worst BuysArnold nominates his 1999 Case 110 tractor equipped with a front-end loader as his “best buy.” “It’s a real joy to operate and doesn’t use much fuel. Also, the loader is easy to take off and put on. It has a powershift transmission. We had to replace the power shift relays which the company paid for. I’d buy another one of these tractors in a minute.”
Case 1150C bulldozer
1 Best Buy0 Worst Buys“My 2002 Kubota MX5000 4-WD loader tractor has had no major problems.
“The 1977 Case 1150C bulldozer I bought used 5 years ago always starts right up. It’s an awesome machine.
“In 2006 I bought a used EZ-Go golf cart equipped with a lift kit and a cargo box with tailgate. It’s a fantastic machine. No problems.”
Case 1194
1 Best Buy0 Worst BuysElton Hickman, Terry, Miss.: “We've had problems with this pile of junk since the day we bought it,” says Elton, unhappy owner of a 1985 Oldsmobile Calais. “The transmission always leaked and was rebuilt at 34,000 miles. The car has had three alternators and all types of electrical problems. Dealer service was poor. You never see dependability mentioned in American car ads. Now I know why.” On the plus side, “My Case 1194 tractor is a dream to drive. No problems after 300 hours. It starts easy and shifts on-the-go. I also like my FMC Sidewinder and Bush Hog finishing mower.”
Case 125 Maxxum tractor
1 Best Buy0 Worst Buys“My 2007 Case 125 Maxxum tractor has a serious design problem. To repair damage caused by the air conditioner’s drain hose, the tractor’s fuel tank, rear wheel and cab all had to be removed. It resulted in a $3,000 repair bill.”
Case 1290 tractor
1 Best Buy0 Worst Buys“Our 1968 Deere 4020 tractor, which we bought used, is a best buy. We’ve had a front-end loader on it since 1974. We’ve used it to handle 1-ton bales all this time. The engine was overhauled at 8,900 hours.
“Our Case 1290 tractor, which we bought in 1986, has more than 10,000 hours on it yet the engine has never been overhauled. It’s a best buy. Our only problem was that the right final drive went out about 12 years ago.
“Our Case 8850 swather has about 2,800 hours on it. We use it to cut about 250 acres of hay per year with hardly any major breakdowns. We’ve custom cut a lot of acres with it.”
Case 1294 tractor
1 Best Buy0 Worst BuysA used Case 1294 tractor is Vance’s “best buy”. “It does everything I ask it to do.”
He’s disappointed with a used Deere 2510 tractor. “It has very little hydraulic capacity for the 3-pt. lift – even less than the last Deere that I sold because of poor hydraulics. The dealer has not been able to fix or adjust.”
Case 135B model
1 Best Buy0 Worst BuysJohn nominates his 2003 New Holland LS 170 skid loader as his “best buy”. “It replaced a 1983 Case 135B model which was a good machine, but the New Holland unit is bigger and more fuel efficient. Also, it works faster, starts better, and is easier to service. It can be used with a lot of different attachments.”
Case 1410
1 Best Buy0 Worst BuysWilliam Fricke, Petersburg, Ill.: William's pleased with his 1985 Vicon double wide hay rake. ‘Does twice the work of one rake with just one tractor and one operator, Has few | moving parts, gently turns hay andI get less leaf loss.”’ Jake Van Eps, Hancock, Minn.; “‘It always seems to be falling apart and nobody seems to want it in trade,” reports Jake, upset with his Bolens | lawnmower. As “best buy" he cites his 1971 | 4020 Deere tractor. “We've not had any expense On it outside of a new clutch. It has over 5000 hrs. on it and doesn’t use any oil." Burton W. Bartz, Princeton, Minn.; “My New Idea 363 manure spreader is a best buy. The worm gear driveis | very smooth and pulls extremely easy for such a large spreader.” Mark Stiegman, Thawville, Ill. “If this was the only bait on the market, the world would be engulfed with rats. I think it’s a complete waste of money,” says Mark, disappointed with Rampage Rat Bait. ‘Placed it side by side with five other brands. Rodents never touched it although other brands were readily consumed," Brian Klapak, Warren, Ohio; ‘My best buys are all Ford products, Lown 7710 and 4610 tractors. They start easily and operate smoothly. The canopies are like a shade tree and the dealer is one of the best in the business. A 1985 Ford XLT Lariat pickup is also a best buy. Rides excellent and gets good mileage. On the negative side, Brian's unhappy with his 1978 Case 1410 tractor. It leaked oil everywhere and the 3-pt. hitch took a genius to operate, Injector pump went out at 1,000 hrs.”’ Daryl Semerad, Dickinson, N. Dak.: ‘‘Stress points are wellreinforced and it has heavier axles and bigger tires than comparable brands," reports Daryl, happy with his 1983 Kiefer 6 by 16-ft. Stockmaster stock trailer. He nominates his 1985 Sears Craftsman variable speed, reversible ¥-in. drill as ‘worst buy”. ‘I only drilled four holes with it in a year's time and the motor burned out just one month after the warranty ran out. I thought Craftsman had better quality tools than this.” Lester Evers, Windom, Minn.; “My 1981 Buick diesel car only had 45,000 miles on it and blew the engine. Buick said “too bad’, | wound up trading for anew car. Once you havea diesel, you're stuck or you'll lose a lot of money.” On the positive side, Lester says, “My 295-250 AC-DC Century welder is easy to operate and will run a 7018 rod smoothly and will do a beautiful job that will hold. My 8070 Allis Chalmers tractor with mfwd has a cab that is tops. The tractor will pull at reduced throttle and come right back Bh nn eee eee Ed ae rst Buys in rpm's under load. With the front wheels pulling, you can go through mud or up hills with little or no slippage. Tractor starts good even in cold weather. It's far better than my old 7060, “IT also like my 1981 Gleaner M2 combine. It’s always done a good job and gives me very little trouble.”
Case 1450 loader
1 Best Buy0 Worst Buys“My Case 1450 loader starts every time and lifts anything I need lifted. It’s very handy. I just wish it had power steering.
“My Bauer 20-volt impact wrench (model 1782C-B) from Harbor Freight is a real workhorse.”
Case 1470 Traction King 4-wd tractor
1 Best Buy0 Worst Buys“My 1972 Case 1470 Traction King 4-WD tractor is easy on fuel. Pulling a 32-ft. field cultivator it uses about 4 1/2 gal. of fuel per hour. Also, it has a lot of power for its size. It’s equipped with a standard transmission and starts good – I never have to use ether to start it. It’s also an easy tractor to work on. I did the heads on the engine and installed new fuel injectors. This tractor just keeps on running.”
Case 1494
0 Best Buys1 Worst BuyRalph Adams, Jr., Navarre, Ohio: “Our Deere 2950 tractor shifts and handles nicely 440 Fanw enow | 2-¢) t Buys and you can usc all the horsepower you buy because the horsepower is rated at the recommended operating speed. “My worst buy ever was a Case 1494 tractor with synchromesh transmission. The tractor’s horsepower was rated at 2,300 rpm's but recommended operating speed was 2,000) rpm’s. At about 100 hrs. the tractor ground gears and leaped whenever you put it into gear. After struggling with the company for a year and a half through attorneys, they still refused to correct the problem. [also had trouble with plastic fuel and hydraulic lines. The first year this tractor was at the dealer’s for at least three months for repairs.”
Case 1594 4-WD tractor
0 Best Buys1 Worst Buy“We’re well pleased with our Case-IH 5220 front wheel assist tractor equipped with a self-leveling front-end loader and grapple fork. It’s well designed and the front wheel assist drive system is built heavy. The cab is quiet and has a lot of room, with control levers that are easy to reach. It’s a good tractor. The quick detach bucket on the loader is also well designed.
“Our worst buy is our Case 1594 4-WD tractor. The hydraulic pump had to be replaced three times and the powershift transmission had to be rebuilt. The engine had to be overhauled twice and then it broke into pieces when a piston rod broke in two and punched a hole in the side of the engine. The only good thing was that our dealer was helpful.”
Case 16 hp garden tractor
1 Best Buy0 Worst Buys“It’s the best lawn and garden tractor I’ve ever owned,” says Lawrence about his 1980 Case 16 hp garden tractor equipped with an Onan engine and 48-in. mower deck. “After one year of use the gears in the oil pump broke, and of course the warranty had just expired. Also, the engine seized up. However, Onan supplied a new engine and the dealer installed it for $125. Since then I’ve been using this tractor all year long. I don’t think 26 years with the same engine is too bad.”
Case 1690
1 Best Buy0 Worst BuysRandy Jacobs, Alden, Minn.: “The Magrath livestock prod hasa very hot spark that really gets hogs moving. Before owning one we really worked to gethogs loaded, Now they can’t wait to get on the trailer.” Thomas W, Rhodes, Horseheads, N.Y.: “Our 1982 Case 1690 broke down every spring and fall each of the five years keptit. A hydraulic line cracked at the pump 4or5 times, The drive shaftto the hydraulic pump broke once in the second year of use. "It broke down every spring and fall each of the five years I kept it." Two soft plugs in the block rusted through and I had to split the tractor to replace one of them, The crankshaft pulley loosened up twice completely stripping splines from the pulley and rounding off splines on the crankshaft. The second time the crankshalt pulley came off, we traded for a 1986 Ford 7710, which is my best buy. It does everything we want it to and we've had only one small problem which the dealer took care of immediately. Very roomy, comfortable cab. The more I use it, the better I like it.”
Case 180 hp front
0 Best Buys1 Worst Buy“My all-time best buy was my Ferguson 30 tractor. My dad bought it before I was born and we still use it on our farm today. Over the years we bought many other Ferguson and Massey Ferguson tractors and they all worked great. As farms grew in size, so did the size of the equipment and tractors. The last Massey Ferguson I bought was a 160 hp, front wheel assist model. As the dealers went out of business in my area I decided to try another brand.
“That resulted in my worst buy - a 1998 Case 180 hp, front wheel assist row crop tractor. This tractor came from another state and had only about 1,200 hours on it. It has had a long list of problems. Here’s all the components that had to be replaced: the head gasket (three times), fuel injector (numerous times), water pump, vacuum valve for the turbo (twice), brake pedal switches, rear wheel bearing and seal, upper lift arm rocker shaft bushings and seals, both rear tires (after they separated), door shock, shifter accumulator (one also had to be recharged), throttle cable, shifter cable, fan belt tensioner, all six injectors, injector pump, both lift arm connector blocks.
“This tractor has about 3,100 hours on it. Now the 3-pt. lift has started to act up again so this will mean more shop time.”
Case 1816B skid steer loader
1 Best Buy0 Worst BuysDennis Schubert, Shannon, Ill.: Dennis is pleased with his Case 1816B skid steer loader. “Works great for cleaning out manure in our 60-ft. wide farrowing house because it can get into tight places which reduces the amount of shoveling that we have to do. We just pile manure in the middle aisle, then push it outside.”
Case 1835
1 Best Buy0 Worst BuysCornie Harthoorn, Doon, Iowa: “The first week we installed Ritchie hog waterers, the hogs started knocking the lids off which caused the water to freeze. The lids are held on with self-tapping screws which makes them easy to assemble in the factory but also gives hogs the satisfaction of destroying something.” He’s happy with his 1985 Case 1835 Diesel skidloader. “It's been trouble-free, and has excellent power and maneuverabil ity along with a good live hydraulic system.”
Case 1835B skid loader
1 Best Buy0 Worst BuysTy’s impressed with the 1994 Case 1835B skid loader he bought used 5 years ago. “I use it to do everything from lifting big bales – which it isn’t rated for – to cleaning out a fair-sized number of corrals, all with no problems.
“My 2004 Ford F-250 has been a dependable pickup over the years. It’s powered by a 6.0-liter diesel engine that works great when it’s warm, but I don’t like having to wait for it to warm up.”
Case 1835C
1 Best Buy0 Worst BuysGlen Oberholtzer, Rutledge, Mo.: “I use it every day of the year. It starts well in cold weather for a diesel and has fast-acting hydraulics,” says Glen about his “best buy” 1988 Case 1835C skid steer loader.
Case 1840 Uniloader equipped
1 Best Buy0 Worst BuysNorman Varner, Buffalo, Minn.: A 1989 Case 1840 Uniloader equipped with a 50 hp Cummins diesel engine rates as Norman’s “best buy”. “It starts easy in cold weather and handles well, We use it to feed silage to our cattle, to clean feedlots, and to push snow. Ithas lots of lugging power even at half throttle. “Our 1988 ProQuality hay basket is another best buy. It self-loads behind the baler and unloads just by opening the rear gate. It’s simple but it works.”
Case 184SC skid steer loader
1 Best Buy0 Worst Buys“I bought a 1995 Case 184SC skid steer loader in 2015 with 1500 hrs. on it. I’ve put 700 hrs. on it since then with no breakdowns except for hydraulic hoses. It’s been a very dependable loader.”
On the other hand, Jacob is disappointed with his 2009 Polaris Ranger 750. “After only a few months we had to take it in to adjust the idle, which turned out to be the first of many regular trips to the dealer to tune the engine. The dealer changed the oil and didn’t tighten the filter properly so all the oil drained out and ruined the engine. There’s no oil safety light on the machine.”
Case 1H 7120 front wheel assist
1 Best Buy0 Worst BuysDennis Rodgers, Dunkirk, Ind.: Dennis likes his 1988 Case-1H 7120 front wheel assist tractor. “I’m impressed with the engine’s power, and the cab is superior to the competition,”
Case 1H 7130 tractor
1 Best Buy0 Worst BuysTed E. Olson, Lewiston, Minn.: Ted's pleased with his 1989 Case-1H 7130 tractor which he bought used, but says it could use one improvement. “It’safun tractor to drive, quiet, and has excellent lights for night work, However, the shift linkage wouldn't go into reverse after the tractor wasn't used over winter, The dealer corrected the problem.” Ted’s “worst buy” is Onduline roofing that he installed on his 1983 45 by 72-ft. Menard’s machine storage shed. “I made the building without any ridge lights or sky lights so I could keep out the birds and it worked. However, within two to three years there were holes around all of the nailsin the roof which caused it to leak. Menard’s was very cooperative in handling the problem. Onduline finally replaced the roofing material, but I had Menard’s tear off the old roofing and install tin. They didn’t charge me anything. They even replaced several purlins that had warped from the leakage. I’mtold that Menard’s no longer constructs any buildings with this roofing. Too many problems.”
Case 210 skid loader
1 Best Buy0 Worst Buys“Over the years we’ve been extremely happy with the performance of Deere equipment. However, we recently purchased a Deere 326 skid loader equipped with a hydrostatic transmission that’s noisy and stiff. Also, the transmission won’t go into low range unless the engine is turned off. Now no one wants to drive it so the machine sits unused in our barn.
“Our 2015 Case 210 skid loader runs smooth and quiet and is a pleasure to operate. Perhaps Deere could learn from this company just how to build a skid loader.”
Case 2292
0 Best Buys1 Worst BuyKen Nelson, Ft. Collins, Colo.: “The extended warranty for our 1986 Case 2292 tractor is our worst buy. The tractor is great but we bought the extended 4-year, 1,800hr. warranty. The problem is that the tractor has the new hour meter that registers ‘true’ hours. In other words, 60 min, of operation adds up toone hour, Old meters were based on engine revolutions and you could cultivate at an idle and put on only one or two hours a day. Now it’s easy to put 12 to 14 hrs. aday on the tractor. The 1,800 hrs. were used up in one year.” Ken’s “best buy” list is headed by his Donaldson post driver he bought from a local farm supplier. “It’s made in New Zealand and drives the postin much quicker than you can drill a hole. The thing I like is that the post is in tight when you drive it, “Also on the best buy side is our 1986 Ford F-250 pickup with a 302 fuel-injected engine. We have 67,000 miles on it and we haven’ teven putnew spark plugs init. [thas plenty of power, starts quickly in all kinds of weather, and does not cough or sputter even onacold morning. Drives and handles very well.”
Case 2470 4-WD tractor
1 Best Buy0 Worst BuysHe likes his 1999 Ford F-150 extended cab pickup equipped with a 4.6-liter, V-8 gas engine and automatic overdrive transmission. “It’s roomy enough to carry four adults and gets a respectable 22 to 25 mpg.
“I bought an International Harvester 1466 tractor from a friend for $4,500 and use it every day. I haven’t had any major problems except I had to buy a new set of Taper-Loc spindles.
“I bought a Case 2470 4-WD tractor at an estate sale for $4,500 and it’s a best buy. It lets me work the ground a little sooner and also use bigger equipment. It’s now my main tractor. It works great in mud.
“My 1986 Honda 3-wheel ATV is a best buy. I put about 600 miles a year on it. Other than gas, oil and filters, and a set of 6-ply mud tires I haven’t spent a dime on it since it was new.”
On the negative side, “The 12-speed drill press I bought from Harbor Freight is a piece of junk. You have to watch what you buy from them. From now on I’ll buy only brand names.”
Case 310 dozer
1 Best Buy0 Worst Buys“I use a Kubota 161-3 excavator in my business, along with an old Case 310 dozer and a Case 1840 skid loader. These small machines can do an impressive amount of work.”
Case 3294
0 Best Buys1 Worst BuyMike Roberts, Ainsworth, Iowa: Mike likes his 1984 Case 3294, 2294, and 2094 tractors. “They're well made, casy to operate, powerful, and economical. I like the 24speed transmission.” On the “worst buy” side, Mike’s unhappy with his 1985 Kane 2 by 4-ft. heat mats. “We purchased nine of them, andeight went badrightaway. The company replaced them, but those mats went bad too, We ended up buying Stanfield mats which we like.”
Case 335 VT
1 Best Buy0 Worst Buys“My 2018 Lindsay VRI 8500 center pivot irrigation system is equipped with a 9500 corner arm unit that’s very uniform (www.zimmatic.com; ph 866 404-5049). The entire irrigation system provides water amounts variably wherever I want.
“My 2014 Deere 2623 VT vertical tillage implement is my worst buy. The rear blades were a disaster but I got no company support. I also had problems with the gang bearings. I finally traded it for a Case 335 VT, which works good.”
Case 40XT skid steer loader
1 Best Buy0 Worst Buys“My 2004 Case 40XT skid steer loader is my best buy. I bought it slightly used last summer with 30 hours on it. It’s a simple, reliable, well-built machine. I’ve put about 400 hours on it with no problems. I use it every day to feed my dairy herd and also to do countless other chores around our farm. This machine has saved a lot of wear and tear on my loader tractor. I don’t know how I got by without it.”
Case 435 skid steer loader
0 Best Buys1 Worst Buy“My 2005 Case 435 skid steer loader equipped with a coupler latch hydraulic system and a cab is my worst buy. I’m not pleased with how the quick coupler latch is designed. Sometimes it works and sometimes it doesn’t. I have to pull on the steering levers to make it work which, during normal operation, causes the system to put extra stress on the coupler system. The Case cab has a small opening which makes it hard to get in and out. The heater breather is located outside the cab and extends over the roof, which makes it difficult to get into our low barn.”
Case 442 garden tractor
1 Best Buy0 Worst Buys“My Case 442 garden tractor, which I bought used 15 years ago, is my best buy. It has required no major repairs. It doesn’t use any oil and still has the original spark plug. It starts instantly.”
Case 446 garden tractor
1 Best Buy0 Worst Buys“In 1982 I bought a new Case 446 garden tractor, which I’m still using to mow lawns and to blow snow. Over the years this tractor has had minor problems, but it still performs flawlessly.”
Case 4490 4WD tractor
0 Best Buys1 Worst BuyVern Krueger, Erie, Colo.: Vern likes his 1991 Sunflower Fallow King 3000 tllage implement equipped with 26-in. blade sweeps. “I’ve used it on 200 acres of fallow ground. It leaves the ground level and pulls easier than my 6-ft. blade did. It’s casy to adjust the depth control and once it’s adjusted it stays in the ground and doesn’t plug up in trash, It’s built sturdy and transports well. A much needed machine for dryland farming. “My worst buy is my 1981 Case 4490 4WD tractor. The engine runs fine but the hydraulic system quits after it warms up. Another problem is thatthe 3-pt. hitch won't stay up. I have to hold the hydraulic levers in position 90% of the time. When I try to shift, the power shift transmission willalmost stop, then jerks forward. If my grandson is riding along with me he'll say ‘grandpa, don’t do that’. It’s hard to explain to a 2 1/2-year-old that’s the best Case can do to repair it.”
Case 450 bulldozer
1 Best Buy0 Worst Buys“My best buy is my 1976 Case 450 bulldozer which I bought used a few years ago. All I’ve done is to repair the rollers and chains. I’d recommend this bulldozer to anyone.”
Case 4890 4-WD tractors
1 Best Buy0 Worst BuysLeo Boddicker, Newhall, Iowa: “I have two Case 4890 4-WD tractors, a Case 2390, and two Case 1370s, All of them perform great and are best buys. “My Case-IH 1680 combine does a perfect job.”
Case 4894 4-WD tractor
1 Best Buy0 Worst BuysDan’s impressed with his 1984 Case 4894 4-WD tractor. “It’s equipped with a diesel engine that runs smooth and is fuel efficient, and with an electric-over-powershift transmission that has worked flawlessly. I like the relative simplicity of older tractors, and I think the company got this model pretty much right.”
Dan says he’s also well pleased with Milligan Canola-based diesel fuel additive (Milligan Bio-Tech, Inc., Foam Lake, Sask., Canada ph 306 272-6284; www.milliganbiotech.com). The company’s website says the product can result in up to a 13 percent increase in fuel efficiency, and up to a 50 percent decrease in engine and injection pump wear.
Case 5100
1 Best Buy0 Worst BuysDuane Weaver, Marshall, Mich.: As “worst buy” he nominates his Deere 7000 Max Emerge planter. “This planter can be a pain at times. Plants no more accurate than my old White plate planter. Even though my fields have very few stones, it has the habit of picking them up and twisting the planter units, which requires time to repair.” On the plus side, he says, “My 895 Versatile Series 3 tractor is one of the best tractors I’ve ever owned, Has good operator comfort and is casy to service. This tractor was built for the farmer and not for the professional mechanics. “Another best buy is my Case 5100 Soybean Special drill. Has done aremarkable job of controlling seed depth so we get an even soybean stand. “Also, my Noble Mix-Till is one of the best finishing and incorporating tools I’ ve ever used. Number one in my book.”
Case 520 loader
1 Best Buy0 Worst Buys“I work for a snow removal company that uses late model Deere 6000 series tractors equipped with model 640 front-end loaders. In my opinion, these loaders are built way too light. There’s no comparison to my own personal 1993 Case 520 loader which I use on a Case 5220 tractor. It’s a no nonsense, indestructible loader.
“The same snow removal company just bought two new Kubota M126X tractors. I never knew a machine could be absolutely perfect until these tractors came along. I can’t decide whether they’re the Cadillacs or the Rolls Royces of the tractor world.”
Case 53 hp 990 tractor
1 Best Buy0 Worst Buys“My best buy of all time is a 1977 Case 53 hp 990 tractor. I bought it used in 1984 with 2,986 hours and it now has 6,404 hours with only a handful of repairs. It’s economical to run and is so handy to have. I wouldn’t want to be without it.”
Case 531 diesel utility tractor
1 Best Buy0 Worst BuysJohn’s the third owner of a 1966 Case 531 diesel utility tractor and says it’s his “best buy”. “For many years this was my primary tractor for plowing, disking, mowing, raking and baling. It handles well, has a lot of power for its size, yet is fuel efficient. Except when pulling a maximum load it burns less than one gallon of fuel per hour. It has a lot of torque which minimizes down shifting. I wish I could get a new one since this one is almost worn out.
“My New Holland TL 80 loader tractor with cab is my worst buy. It has a marginal torque curve which produces excessive speed drop of the pto with varying pto load. It has had a lot of small but recurring problems, and the fuel effiency isn’t the greatest. Also, the hydraulics are often very slow. However, this tractor does handle well and is comfortable to operate. It would have been a much better tractor if it had a Perkins diesel engine. It has about 1,000 hours on it.”
Case 58 loader designed
0 Best Buys1 Worst BuyRonald Lindner, Watertown, S. Dak.: rst Buys revious page) On the “worst buy” side, Ronald’s unhappy with his 1981 Case 58 loader designed for a 1390 Case tractor. “The loader sets out too far. I shortened the main frame, but the holes wore out right away. The dealer did all he could, but the company gave me the run-around,”
Case 5800 chisel plow
1 Best Buy0 Worst Buys“It has the best design and performance of anything in its class,” says Eugene, pleased with his Case 5800 30-ft. chisel plow. “This chisel plow does a great job of penetrating hard soil. The design of the shanks is excellent for clearing trash. The bottom end of the shank is slotted, which makes changing sweep points a much easier job.”
Case 5806
1 Best Buy0 Worst BuysDuane Pearson, Ogilvie, Minn.: “We bought our 1981 Case 5806 tractor with loader used last spring and haven't been sorry. It has good power and weight for loading. The hydrostatic drive is reliable and fast. It's more maneuverable than our previous loader tractor, a Ford 3400,” Best And Wo (Continued from preceding page) bought it new in 1967 and it’s never needed a major overhaul. The tiller has been a joy to operate for all large garden work. We do 342 acres with it. It's a flawless machine."
Case 580CK tractor loader backhoe
1 Best Buy0 Worst Buys“One of my best buys ever was a 1971 Case 580CK tractor loader backhoe, which I still own. It probably has at least 30,000 hours on it but still doesn’t use any oil. It has been used and abused a lot over the years, but now I use it just to plow snow. I’m 86 years old so I guess this machine and I will go out together.”
Case 580 Super K backhoe
1 Best Buy0 Worst Buys“My Case 580 Super K backhoe has more than 5,000 hrs. on it and is the best machine I’ve ever owned.
“I’ve used Husqvarna chainsaws for years, but the last 2 saws have been disappointing. They lack power, have plastic parts, and are hard to start and keep running. They haven’t been reliable.”
Case 580 Super L backhoe
1 Best Buy0 Worst Buys“I purchased a 1995 Case 580 Super L backhoe with an extend-a-hoe. It has a 30-gal. tank which barely keeps me going for eight hours. My trade-in was a 580 K Case with only an 18-gal. tank, and I could run it hard for more than 10 hours. They told me the poor fuel efficiency was just the nature of the beast because the engine has a turbocharger and 15 more horsepower than the 580 K model. A Case engine is good for only about 3,500 hours, if you can even get that many hours on it. The booms are made out of ductal steel which isn’t even as good as cast iron. I’ve worn out the engines in both machines. I also broke the boom on both of them.
“I have a 1993 Chevrolet 2500 with windshield wiper problems. My son has a 1994 1500 model which was had a factory recall. However, mine wasn’t recalled apparently because there weren’t enough complaints. I was told that I’d have to pay to fix the wiper problems. I’d like to know if I’m the only one with this problem.
”I’ve tried to wear out my Deutz 6250 50 hp tractor but I don’t think I can. It’s my best buy. It doesn’t use a lot of fuel. It keeps on going and going, just like the Energizer bunny. The problem is that they quit selling this tractor in the U.S. Parts are still available, but not the tractors.”
Case 590 backhoe
1 Best Buy0 Worst Buys“I’ve been a heavy equipment mechanic for 40 years, and I really like the Gear Wrench 8-piece reversible ratcheting combination wrench set that I bought at Sears.
“I don’t like the hydraulic system on my 1999 Case 590 backhoe because there’s no way to activate the rear hoe without it jerking. As a result, it’s dangerous for anyone to stand near the backhoe when I’m digging.”
Case 600 diesel tractor
1 Best Buy0 Worst BuysJames Walker, Leonard, Minn.: A used 1985 Hesston 1091 mower-conditioner rates as James’s “best buy”. “The header is suspended so well that it floats over gopher mounds and rocks as if it could see them coming. It runs smooth and quiet and is an incredibly well-engineered piece of equipment. “The header is suspended so well that it floats over gopher mounds and rocks as if it could see them coming.” “One of my best buys ever is my 1959 Case 600 diesel tractor. It has power steering, live dual hydraulics, live pto, is fuel efficient and has plenty of power. I bought it used four years ago for only $1,200 and my only maintenance expense has been to replace the fan belt and fuel and oil filters. Ithas an oil-bath hand clutch which is what turns most people away from it but, even though it’s 34 years old, it'll probably sull outlast some tractors built in 1993. It has features such as triple fuel filters and water drains that make me think it was designed to last a lifetime. It’s quite a contrast to the high tech, high torque, high-priced, throwaway stuff we see so much of nowadays.” On the negative side, James is disappointed with his Deere 450 mower equipped with a 9-ft. sickle bar. “It did a good job of cutting, but the wobble box was difficult to work on. I don’t recall this mower going for a full season without requiring at least one new set of bearings and a few new sickle head bushings.”
Case 60 XT skid steer loader
1 Best Buy0 Worst BuysLynn’s the owner of a 2003 Case 60 XT skid steer loader as well as a Hick hydraulic rotary tree saw that mounts on the skid loader (Hick Fabrication, Berryton, Kansas ph 785 862-8603). He says they’re both best buys. “The tree saw is easy to maintain and cuts scrub trees like crazy. The skid loader runs great and has a lot of power.
“I’m also well pleased with my Miller plasma cutter.
“We have a 1953 Farmall Super M loader tractor equipped with a live hydraulic pump that drives off the timing gear. The problem is that we were always breaking the timing gear when lifting heavy loads. To solve the problem we had a machinist cut the center out of a good timing gear, leaving about one inch of the original gear. He then machined out a solid steel hub and bolted the new hub to the original gear. We haven’t had any problems with it since.”
Case 644 Wheel Loader
0 Best Buys1 Worst Buy“I like my 3 hp, 2-cycle, compact DR trimmer/mower (Country Home Products, Ferry Road, Box 89, Charlotte, Vt. 05445). “I have a large lawn with a lot of trees and shrubs to trim around. With an ordinary weed whacker my back would give out in 25 to 30 minutes, but my DR trimmer lets me do all the trimming in one shot. I also have better control of the cutting head. No more back aches. “My Case 644 Wheel Loader, bought used, is my worst buy. It runs good but is so underpowered I can’t even push the bucket into a pile of loose gravel. What a wimp.”
Case 7240
1 Best Buy0 Worst Buys“It’s an excellent all-around tractor especially with the mechanical FWD option,” says Jarrett, pleased with his 1994 Case 7240.
Case 750 crawler tractor equipped
1 Best Buy0 Worst Buys“My 1995 Ford F-250 4-WD pickup equipped with a Power Stroke diesel engine is my best buy. I use it almost every day. No problems.
“My Case 750 crawler tractor equipped with a bucket and backhoe is also a best buy.”
Case 770 diesel
1 Best Buy0 Worst BuysTom’s the owner of a “best buy” 1968 Case 770 diesel. “It’s needed very few repairs, is fuel efficient, easy to service and is just the right size for mowing, raking, and baling hay as well as hauling manure,” he says. “I also have a Case-IH 5130 tractor that I use for loader work. The shuttle shift on the steering column is very handy but I have only 3,600 hours on it and already have had to replace the front wheel seals.”
Case 800 case-o-matic diesel tractor
1 Best Buy0 Worst Buys“My best buy is the Case 800 Case-O-Matic diesel tractor I bought used in 1971. I used this tractor for farm work, the last 20 years with a hydraulic-operated loader. Other than a rebuilt diesel pump the tractor has been trouble-free. It’s still going strong.”
Case 8360
1 Best Buy0 Worst BuysEarl Engelbarts, Malcom, Iowa: “Our 3-year-old Case 8360 hay conditioner equipped with stub guards is our best buy. It cuts hay in places where the old one would plug up. We haven't had to replace any parts yet.”
Case 885
1 Best Buy0 Worst BuysJerry Barnes, Danville, Ill: “In 1985 I bought a new Chrysler LeBaron witha 2.6 liter, 4 cyl. engine. The engine on this car never ran right. Although it would start good and run down the road fine, you never knew if it would accelerate at a stop light or cough and die. After many return trips to the dealer and near misses at 4-way stops, I traded it fora 1987 Chevrolet Celebrity with a 2.8 liter V-6 engine which is a nice car with a good engine. “Talso like my 19874WD Chevrolet 1ton pickup with 454 engine. I'd owned a 1983 Chevy 1/2-ton with a 305 engine but it was always short on power. With the new truck we have plenty of power and load “I've had it for 9 years and it's still a reliable machine," capacity. Can pull heavy loads with no problems. “Another best buy has been an International 1460 combine. I've had it 9 years and it’s still a reliable machine that’s relalively easy to work on. It may not have all the advanced gadgets as the new ones, but it doesn’t have a payment book in the cab either.” Jim Sherman, Andrews, N.C.; “The money I've spent trying to solve adaptor plate, heat and engine problems has cost more than any fuel savings | might have received had I got any,” says Jim, disappointed with M3 and MS5 Fish carburetors. “The manifold adaptor plates warped, allowing loss of vacuum. Also, the lines, aa t Buys ) pump and float bowl are so heat sensitive that fuel tends to vaporize in the line before it’s in the carburetor bowl, even when wrapped in insulating tubing.” George Stewart, Fayetteville, Tenn.: “My 1987 Case 885 tractor with 2250 loader has its plusses and minuses. It has plenty of power and works well to clean out low barns. Minuses are the hydraulic control location, drawbar height, and case of filter change and oil addition with the bucket on. Also, the steering radius is more than | like. Loader is excellent for moving round bales and manure handling. [ also like the ease of mounting.” As “worst buy” he nominates his 1987 Isco hi-lift bale mover. “The bolts were grade two inthe third arm. They broke while picking up the first bale. The lift crimped 2 hydraulic lines on the tractor and the hinge points are built too weak. It works alright after replacing the grade 2 bolts with grade 8. ! “I do like my 10-20 Grain-O-Vator with hydraulic controls. It’s worked well with no major breakdowns. My New Holland equipment, including a 315 baler with model 80 thrower, 512 manure spreader and 478 haybine all work well. They've been trouble-free and the haybine, bought new in 1976, cuts 300 acres a year and still does a good job of cutting and conditioning hay. The only problem has been the chains that drive the rollers.” George also likes his 1982 International 800 4-row plate planter and Lifetime hydraulic hog trailer. “Planter’s seed placement and no-tilling ability have been excellent. The only problem has been the fertilizer drive chain and that the disk openers wear too fast. We've used the trailer almostevery day for six years with no problems.”
Case 8930 front wheel assist
0 Best Buys1 Worst Buy“My worst buy is a 1998 Case 8930 front wheel assist tractor that I bought with only 1,200 hours on it. It now has 3,100 hours and I’ve had to replace two head gaskets, two fuel injectors, a water pump, two vacuum valves for the turbocharger, both brake pedal switches, a rear wheel bearing and seal, rocker shaft bushings and seals for the upper lift arm. Also, both rear tires separated at the wheel rim and had to be replaced, and I had to replace both hood shocks, a door shock, shifter accumulator, throttle cable, shifter cable, fan belt tensioner, and both lift arm connector blocks.
“On the plus side, my dealer fixed every problem.”
Case 900 B
1 Best Buy0 Worst Buys“I’m 80 years old and have been retired for 17 years, so I haven’t bought any major equipment lately. However, we still live on the farm and have saved several items from the good old days. All of these machines continue to serve us well, and in addition they keep a lot of good memories alive. Once upon a time, they were all best buys.
“The machines include a Grasshopper mower with an 18 hp Briggs & Stratton gas engine; an Allis Chalmers 720 yard tractor with a 20 hp Onan engine; a Miller portable welder; and a series of Bobcat skid steer loaders, each one better than its predecessor. The newestone is a 742 model. We’ve also saved several tractors - a 1958 Case 900 B, a 1949 unstyled AR Deere, a 1946 Farmall H, and my favorite, a 1949 Oliver 88. It was ahead of its time and was equipped with live hydraulics, pto, and a smooth 6-cylinder engine. I added a homemade 3-pt. hitch to make it even more useful.”
Case 90XT skid loader
1 Best Buy0 Worst Buys“My 1998 Case 90XT skid loader is a real workhorse and runs like a top. I plan to run it on biofuel by adding a vegetable oil tank to it with a conversion kit from www.greasecar.com. I added a similar kit to my 2000 Volkswagen Beetle diesel car and have had excellent results over the last three years. I love passing up those expensive gas stations.”
Case 930
1 Best Buy0 Worst BuysDavid Fricker, DeValls Bluff, Ark.: “The best tractor I've ever owned is a 1967 Case 930 Comfort King, It’s got more than 6,000 hrs. on it with no major down time. I changed the electrical system with a generator over to a Ford electrical system with an alternator to get cnough electricity for night work. “The best dozer blade I’ve ever used is an 8-ft. Waldon that mounts on my Case 930. The blade support frame remains on the tractor all the time. The blade mounts on the support frame with two pins.”
Case 95 XT
1 Best Buy0 Worst Buys“At 2,400 hours the engine on our 1998 Gehl 5635 SXT skid loader blew up while idling. Before that we had to replace a hydraulic drive pump after it self destructed. Then the frame started cracking. We sold the machine a few years ago and bought a Case 95 XT which we like.”
Case 990
1 Best Buy0 Worst BuysBruce has had good luck with his 1975 Case 990. “I bought it with only 1,250 hours on it. It’s been very dependable in all ways except one - the brakes grab severely making it somewhat unsafe to drive.
“The only improvement that could be made would be in routine maintenance. The power steering pump has to be removed in order to replace the filter and it has spin-out wheels that do not hold in the position they’re set at.”
Case CX31
1 Best Buy0 Worst Buys“It has great digging power for a small track hoe,” says C.W. about his Case CX31.
“My Deere 4610 is a great tractor, but the plastic hood and nose on it fell apart after just 600 hrs. The dealer wouldn’t help so I contacted the company but got no help. We keep the tractor inside a shed whenever it’s not being used so it’s been well taken care of.”
Case D33 2-WD tractor
1 Best Buy0 Worst Buys“My 2004 Toyota Highlander has 252,000 miles and gets 18 to 30 mpg. I haven’t had any problems with it.
“My 15-year-old Case D33 2-WD tractor has never caused any problems in over 800 hrs.
“I purchased my 1996 Ford 7.3 L F-250 used with 77,000 miles. There have been no mechanical issues in 252,000 miles.”
Case D580 backhoe
1 Best Buy0 Worst Buys“It’s the best all-around farm machine we own,” says Charles about his Case D580 backhoe and loader. “We use it every day and it’s always ready to go. The 188 diesel engine starts easy in cold weather and is very economical. We’ve used this machine for more than 25 years and it’s still going strong.”
Case DC tractor
1 Best Buy0 Worst Buys“My best buy of all time is my 1948 Case DC tractor which I bought used 25 years ago. It still runs great today. The engine always starts right up, although sometimes I have to use the hand crank to start it. It has even won a few trophies in tractor pulls that we participate in. They don’t build quality tractors like this any more.”
Case IH 1063 6-row corn head
1 Best Buy0 Worst BuysDan Biddinger, Ithaca, Mich.: “Itplants seeds accurately and at the right depth and is set up to apply liquid fertilizer. It’s an excellent buy,” says Dan, pleased with his White 5100 12-row planter. “Our Case-IH 1063 6-row corn head is also a best buy. It leaves corn stalks in excellentcondition for plowing or chiseling and works great in down stalks.”
Case IH 1300 sickle mower
0 Best Buys1 Worst BuyGeorge Langenfeld, Harlan, Iowa: “So far I've had no problems atall with it,” says George, pleased owner of a 1989 White 160 2-WD tractor. “The air ride seat is more comfortable than any other seat I’ve used.” George has had trouble with his 1989 Case-IH 1300 9-ft. sickle mower. “It plugs easily and the cable that raises the bar isn’t strong enough. It slips off the pulley and gets caught between the pulley and clamp where it gets torn up.”
Case IH 1620 combine
1 Best Buy0 Worst BuysTom Ewing, Olathe, Kan.: Tom’s pleased with the ease of operation and performance of his 1990 Case-IH 1620 combine. “Two pulleys and a cleaning auger drive shaft broke but were covered by the warranty. “My 1989 Deere 4055 tractor is a pleasure to drive. I purchased it equipped with a Westendorf loader which also works well. “T’'ve had some problems with a Bush Hog 9-f1. disc mower that I bought new in 1990. A hub on the belt drive pulley broke. It was covered by the warranty, but I had to wait three weeks for parts.”
Case IH 1640 Axial flow combine heads
1 Best Buy0 Worst BuysRoger L. Liehr, Chambersburg, Ill.: ~ Roger L, Liehr, Chambersburg, Ill.: Roger’s 1990 Case-IH 1640 Axial Flow combine heads his “best buy” list. “It does agood job, is quiet, fuel efficient, and doesn’t have as many moving parts as some other brands, Dealer service has been excellent.”
Case IH 1650 combine
1 Best Buy0 Worst BuysDel Bates, Acme, Alberta: Del's satisfied with his 1990 Case-IH 1650 combine. “It’s very trouble-free, casy to set, and convenient to service, The cab is quiet and the controls are easily accessible and offer positive response.”
Case IH 1660 4-WD combine
1 Best Buy0 Worst BuysBill Leffler, Americus, Kan.: Bill says his 1990 Case-IH 1660 4-WD combine does an excellent job of threshing and is a “best buy”. “This combine is fuel efficient and simple to service. Of course, it’s 4-WD so it takes a litde more turning room. The grain tank could be a little larger and the bottom sieves could be easier to adjust.”
Case IH 1660 Axial flow combine isa
1 Best Buy0 Worst BuysDean Easton, Remsen, Iowa: Dean's had good luck with his 1991 Yetter 3730 folding ridge till 30-ft. rotary hoe. “It’s wide enough to cover a lot of acres, but light enough that our Deere 4020D tractor can safely lift it. It’s aggressive enough to kill weeds without hurting our crops and rarely plugs up in heavy crop residue. We were able to reduce herbicides and still get the best weed control we've had in years. “My 1990 Case-IH 1660 Axial Flow combine isa best buy. It has lots of capacity, runs smooth, and threshes with little damage. Ithas had few problems and works well with our Deere 643 corn head and Deere 653A row crop head which we mount using a Bish header adapter (Harv’s Farm Supply, Giltner, Neb.). Makes harvest fun. “My worst buy is my 1991 Yetter no-till cultivator. It has four discs per row unit. The problem is that the row units aren’t strong enough for no till or ridge tll. To the company’s credit, they did take my cultivator back. It’s an excellent cultivator for minimum tillage, but shouldn't be sold as a no-till or ridge till cultivator.”
Case IH 1680 Axial flow combine
1 Best Buy0 Worst BuysRodger Geisick, Wiggins, Colo.: “It has plenty of power and capacity and threshes grain clean,” says Rodger, pleased with his 1989 Case-IH 1680 Axial Flow combine.
Case IH 1840 skid steer loader
1 Best Buy0 Worst BuysArthur Timmel, Collins, N.Y.: “My 1991 Case-IH 1840 skid steer loader is handy. I use a bucket and set of pallet forks with it. It starts and runs good. The only problem I have is with the pallet forks. They can’tbe locked into place to keep them from going sideways when I turn, [should be able to lock them into position like on New Holland and Bobcat models, Otherwise it’s far superior to them.”
Case IH 1840 Uniloader
1 Best Buy0 Worst BuysClarence Dove, Seneca Falls, N.Y.: Clarence is pleased with his 1990 Case-IH 1840 Uniloader. “It’s areal pleasure to run, has power to spare and responsive controls.”
Case IH 2250 loader
1 Best Buy0 Worst BuysS. Ridgely Morison, Delmar, Del.: “My 1988 Case-IH 2250 loader can be mounted orremoved in 5 to 10 min. from my International 656 tractor. “My 1987 Case-IH 5100 grain drill does an excellent job of planting wheat, soybeans, and milo, The adjustable depth press resultinan even crop stand in any soil type.”
Case IH 2255 loader
1 Best Buy0 Worst BuysRichard MacDonald, N. Manchester, Ind.: “It’s built to take heavy use day in and day outand has to be one of the best loaders on the market,” says Richard, pleased with the Case-IH 2255 loader that he mounted on a 674 diesel utility tractor, “IL lifts high and is easy to mount. However, I don't like the 72-in, bucket equipped with manure lines and tine cover, It wouldn't load manure or corn, redesigned the bucket by bolting sides on the tine cover the full depth of the bucket and bolted a high-backed spill guard on it so manure wouldn't spill back onto the tractor. would think Case-IH “It's built to take heavy use day in and day out and has to be one of the best loaders on the market.” engineers would think of these things.”
Case IH 2294 tractor equipped
1 Best Buy0 Worst BuysNelson Howell, Jerseyville, Ont.: “It steers too slow and the powershift jerks at high engine rpms,” says Nelson about his inate dUYS Case-IH 2294 tractor equipped with mechanical front wheel drive. Nelson likes his Gehl fingerwheel rake. “It makes windrows the exact width of our round baler.”
Case IH 3309 mower-conditioner
1 Best Buy0 Worst BuysRoy Magler, Amery, Wis.: “Our best buy is our Case-IH 3309 mower-conditioner. It doesn’t plug in down, tangled, or wet hay. Does a very good job of conditioning and has a modest power requirement.”
Case IH 365 field cultivator
0 Best Buys1 Worst BuyMike Lefever, Longmont, Colo.: Mike is disappointed with his Case-IH 365 field cultivator. “I can’t work more than an hour at a time without losing a bearing on the roller baskets, and bolts constantly fall out. I’ve used it on about 150 acres and have broken 35 S-tines. I spend more time repairing it than using it. A thousand times over, I wish I'd never spent $8,500 to buy it. At the very least, I wish I would've financed it so I could let the company repossess it. However, I doubt they’d ever want it back.” On the positive side, “My New Holland 116 swather is a best buy. It cuts hay clean at6 mph and makes a neat fluffy windrow.”
Case IH 385 tractor
1 Best Buy0 Worst BuysJohnny W. Garrison, Jasper, Ga.: “My 1990 Case-IH 385 tractor has performed well. The handling, ride, power, and hydraulics make this tractor second to none, I highly recommend it for general farming needs.”
Case IH 3900 disk harrow
1 Best Buy0 Worst BuysRobert Gardner, Chester, Md.: “We're really pleased with our Case-IH 3900 24-ft. disk harrow. It disks nice and level.”
Case IH 5120 4WD tractor
1 Best Buy0 Worst BuysMike Edel, Scottsville, Mich.:; Mike’s the satisfied owner of a Case-IH 5120 4WD tractor. “Handles easy and all controls are easy to reach. The synchronized transmission makes it easy to shift into any gear and I can go in reverse without using the clutch. It’s also fuel efficient.”
Case IH 5120 Maxxum tractor equipped
1 Best Buy0 Worst BuysKen Zienstra, Zeeland, Mich.: “My 1990 Case-IH 5120 Maxxum tractor equipped with mechanical front drive can turn shorter than the 2-WD tractor I owned before. The engine is only a 4-cylinder, but it’s very powerful and lugs great. The cab is easy to get on and off. Deere doesn’thave a tractor that can compare to this one. It can pull almost anything I own. I'd never buy another tractor without front wheel drive assist. The 4-speed powershift ransmission is very smooth,”
Case IH 5130 Magnum
1 Best Buy0 Worst BuysRaymond Carrier, Monmouth, Ill.: Raymond says his 1991 Case-IH 5130 Magnum is a “best buy”. “This tractor is much more powerful than the horsepower would indicate. It has temendous engine torque from 1,000 rpm’s to full throttle under full load. Handles nice, has a quiet cab, and is fuel efficient.”
Case IH 5140 Maxxum tractor equipped
1 Best Buy0 Worst BuysRob Dewitz, Steele, N.D.: Rob's “best buy” is a 1991 Case-IH 5140 Maxxum tractor equipped with mechanical front wheel drive and a 940 Farmhand loader. “This is my first tractor with front wheel drive, but it won’t be the last. The transmission is hard to beat for loader work. My only complaint is that the hydraulics are a little too slow and there’s no precleaner for the air cleaner.” He says his Northern Hydraulics pressure washer pump is a “worst buy”. “This 3 gpm 1,500 psi pump didn’t have as much pressure as my old 2 gpm 1,000 psi pump which had a crack in the side. I finally discovered that part of the bypass was upside down, but it still doesn't work that great. The company hasn't helped at all.”
Case IH 5200 drill
1 Best Buy0 Worst BuysWilliam Bame, Findlay, Ohio: William nominates his 1990 Sunflower 4211-09 disk-chisel as a “best buy”. “It’s a wellmade unit that maintains very even depth thanks to lots of built-in weight and the walking tandem axle, which really helps when I go over corn rows at angle. “I'm also pleased with my 1989 Remlinger RTC equipped with 3-pt. hitch that’s teamed together with a Case-IH 5200 drill. They do an excellent job tilling and seeding.”
Case IH 5230 tractor equipped
1 Best Buy0 Worst BuysJack’s pleased with his 1994 Case-IH 5230 tractor equipped with a Case 520 loader. “We like the left hand reverser. It has adequate power, good visibility, fast hydraulics, and a quick-tach bucket and grapple fork. It has about 1,600 hours and has been trouble-free.”
Case IH 5400 no-till drill
1 Best Buy0 Worst BuysAlfred Meyer, Chillicothe, Mo.: Alfred’s had good luck with his 1991 BluJet LandTracker 15-ft. implement caddy and coulter bar disk and 1991 Case-IH 5400 15-ft. no-till drill. “The drill and caddy are a dream to operate together. The LandTracker (Blu-Jet Products, Thurston Mfg. Co., Hwy. 87A, Box 218, Thurston, Neb. 68062) is built heavy and is nearly indestructible, It has both front and rear Cat. Ill. 3-pt. hitches that allow me to mount the coulter bar disk on the front hitch and the drill on the rear hitch. The drill is builtheavy and is easy to adjust. I really like its extra capacity and wide lids. “Our two Deere 4020 diesel tractors are also best buys. Both have over 6,000 hours and run and look like new. The best thing 44+«FC ARM CHOW oe 2 about them is that they’re tough enough to pull a heavy drill, yet nimble enough to chase cows.”
Case IH 5600 cultivator
0 Best Buys1 Worst BuyHarold Weppler, Morse, Sask.: “It makes the best round bales on the market,” says Harold, owner of a 1988 Deere 430 round baler. “It’s simple to operate and requires little maintenance. “My 1984 Deere 7721 pull-type combine is also a best buy. It does a good job, is easy to adjust, has lots of capacity, and holds its value.” On the negative side, “The feeder chains on my 1989 New Holland 358 mix mill were installed backward. The mill's engage pin sometimes flies out under a load. The dealer couldn't fix it. Ever since Ford took over New Holland the quality has been poor. “My 1986 Case-IH 5600 cultivator is also a worst buy. Two sets of shanks had to be replaced and the wing lift binded and fell down, bending the axle. The wing lift holdup tower tore out of the frame and left hoses dragging. The walking beam axles had to be rebuilt twice.”
Case IH 600 forage blower
1 Best Buy0 Worst BuysErling Swiggum, Dodgeville, Wis.: Erling owns a 1990 Case-IH 600 forage blower. “This baby will really handle a lot of material. A Deere salesman recommended it to me. “Another best buy is my 1990 1,000-gal. Mueller bulk milk tank. [t cools milk down to 38 degrees by the time I’m done milking. Reduced my electricity bill, too.”
Case IH 6200 press wheel grain
0 Best Buys1 Worst BuyJohn Reese, Hiawatha, Kan.: John's had trouble with his Case-IH 6200 press wheel grain drill. “I can’t keep tires on the end press wheels. I was told by a dealer to replace them with new tires and use an adhesive between the tire and wheel. It didn’t work. Can anyone help me solve this problem?”
Case IH 6500 conser-till plow
1 Best Buy0 Worst BuysJohn Christen, Albany, Minn.: “My 1991 Polaris 350 liquid-cooled 4-wheeler is a best buy. use it for chasing cattle, building fence, checking crops, pulling trailers, traveling between farms, etc. This is my second Polaris 4-wheeler and I'll never own another brand. “My 1988 Case-IH 6500 conser-till plow is also a best buy. It’s never plugged up in corn stalks. The hydraulic-operated disk can be easily adjusted for working at different depths. “My 1988 Sanborn portable 2-cylinder, 3 hp electric air compressor is a worst buy. After only a little use the air hose became rotten, and the electric motor always started hard, It recently quit altogether.”
Case IH 7110 4-WD tractor isa
1 Best Buy0 Worst BuysStephen Fehnel, Easton, Penn.: “Our 1970 International 826 tractor is our best buy of all time. Itlooks as good now as it did when we bought itand has over 6,500 hours on it. We use it to bale hay, spread fertilizer, and do various other jobs around our farm. We’ ve never touched the engine other than to mount a straight chrome stack on it, It runs like a champion. In fact, it has taken first place in tractor pulls in the 9,500-Ib. farm stock class. We're well pleased with it and will never sell it. “Our 1990 Case-IH 7110 4-WD tractor isa best buy. We’ ve always owned International tractors but this model is definitely one of the best. We haven't had to use ether to start iteven in the coldest weather. So far it has worked great.”
Case IH 71202-WD tractor
1 Best Buy0 Worst BuysVernon Munson, Brunswick, Mo.: Vernon likes his 1989 Case-IH 71202-WD tractor. “I've used it about 900 hours without much trouble and have had good dealer and company support. I’m well satisfied with it. The only negative is that the cab door should be stronger.”
Case IH 7130 tractor
1 Best Buy0 Worst BuysDan Hurley, Elmira, N.Y.: “My 1991 Ford F-250 pickup is my worst buy. It had less than 8,000 miles when the reverse gear went out of the standard transmission. It took over a month to get parts. I was told by a dealer employee that these transmissions aren’t built heavy enough for a 3/4-ton pickup.” Max R, Schiele, Jr., Lambert, Miss.: Max says he’s generally satisfied with his 1990 Case-IH 7130 tractor but he’s had a few problems, “It has adequate power and handles well with good comfort and fuel economy. However, the engine block could be improved. It’s asolidcast block, and I've had problems with sand holes and cracking cylinders, I’ve also had to update too many items al my own expense,”
Case IH 71304-WD tractor
1 Best Buy0 Worst BuysGarr Wayment, Burley, Idaho: "My Case-IH 71304-WD tractor performs well and is economical, We have an excellent local dealer who performs all updates promptly."
Case IH 7130 Magnum
1 Best Buy0 Worst BuysRay Johnson, Moville, Iowa: “This tractor has plenty of power and I really like how itshifts,” says Ray, pleased owner of a 1989 Case-IH 7130 Magnum. “It offers easy maintenance, handy controls, convenient electronic 3-pt. control, and the cab is easy to enter and exit.” Ray's “worst buy” is his 1989 Oldsmobile 98 Brougham Regency. “The chrome moldings don’t line up right, the seat pleats are sewn unevenly, the windows don’ tclose tight, and the license plate holder had missee OR Pee sO Adrian’s had good luck with his Makita 1/2-in, 2-speed hammer drill, model HP 1310, “It’s lightweight but powerful enough to drill holes in concrete, and has handy switches forchanging speeds and for switching between forward and reverse.”
Case IH 7140 Magnum tractor equipped
1 Best Buy0 Worst BuysPatrick Wrisley, Burlington, Penn.: Patrick's had trouble with his 1989 Chevrolet K2500 pickup equipped with an electronic fuel-injected engine and 4-speed creeper low transmission. “It has 60,000 miles and already I’ve replaced the ball joints, tie rod ends, head gaskets, a door handle, oil cooler lines, and three sets of front brakes. The transmission shift lever wore so bad that it wouldn't shift any more so I rebuilt it. It takes 30 to 60 seconds to engage the hubs for 4-WD. It gets only 10 mpg at the most.” Roy Wendte, Altamont, III; Walter's “best buy” is his 1990 Case-IH 7140 Magnum tractor equipped with mechanical front wheel drive. “It’s extremely comfortable to drive and the assurance of the 5-year warranty makes it one of the most productive pieces of equipment I own. The design makes it easy to service and operate.”
Case IH 7190 tractor
1 Best Buy0 Worst BuysJohn McCarter, Shelby, Mont.: “It has an excellent air conditioner and shifts especially well,” reports John, pleased with his 1990 Case-IH 7190 tractor.
Case IH 8350 mower conditioner
1 Best Buy0 Worst BuysPaul McKie, North Augusta, S.C.: “It's heavy, well built, and has accurate seeding rates and depth control,” reports Paul, pleased with his 1988 Lilliston 9690 no-till drill. “I. can use it in pasture, crop residue, or conventional seedbeds.” “My Surge premium soft 10050 milker inflations offer a rare combination of increased milking efficiency and reduced liner slippage. Paul says his 1989 Case-IH 8350 12-ft. mower conditioner is well built, quiet, and runs efficiently. “It handles tough crops yet is gentle on alfalfa and requires no more horsepower than my older 9-ft. model.”
Case IH 8380 mower conditioner
1 Best Buy0 Worst BuysHarvey Cannon, Spur, Texas: “It's a pleasure to operate and is a high capacity machine,” says Harvey about his “best buy” Case-IH 8380 mower conditioner, “I've used it for three years with only minor problems. It has a low side draft and the header has good floating action. It’s quite an improvement over the older Deere model that I had been using.”
Case IH 8420 round baler
1 Best Buy0 Worst BuysGerald Lintner, Jackson, Mo.: “It makes tight, uniform bales that we can stack witha small tractorand front-end loader, I'd buy it again,” says Gerald, pleased with his 1988 Case-IH 8420 round baler.
Case IH 8460 round baler
1 Best Buy0 Worst BuysMichael Pracheil, Dorchester, Neb.: “My 1989 Case-IH 8460 round baler works good and is easy to operate. However, the hitch is hard to hook up and the pto shaft is too heavy. The pickup should have wheels so that the teeth on it don’t break so easily. It also should be able to do a better job of baling light straw - it doesn’t feed in properly.” ominate t Buys buy. It wouldn’t start after the temperature dropped to only 20 degrees. tried a new starter, arebuilt starter, a new-design starter, and then rewired the electrical system and cleaned all ground connections but nothing helped. Finally I sold the tractor with about 2,500 hours on it. [heard the new owneralso replaced the starter.”
Case IH 8480 baler
1 Best Buy0 Worst BuysDavid R. Cook, Marshall, Mich.: “Our 1991 Hardi TR500 sprayer is a worst buy. Nozzles and nozzle screens plug continuously. Nozzle check valves plug when using dry fIowable materials. Self cleaning screen often plugs. If it does self clean, it sends dirt back into the spray tank. The electric valves open too slow for spot spraying herbicides. The pressure gauges are too ninate suys small and hard to read. Everything is metric and the plumbing is too complicated. When the tank has less than 50 gal. in it, the gauge won't show the volume. When there’s 30 gal. or less in the tank and the sprayer is on sloping ground, the pump will suck air causing the sprayer to lose pressure. It’s very difficult to finish a job without having a lot of leftover chemicals in the tank. “Our 1991 Deere 750 no-till drill isa best buy. We've used it to seed soybeans and wheat in both no-till and conventional till with excellent results. Iteven did a good job seeding beans into irrigated corn ground that hadn’t been touched after harvest. The beans made 53 bu./acre.” Myles C, Elsberry, Wausa, Neb.: “Our 1992 Case-IH 8480 baler is a best buy. It may not make the best looking bales in the world, but we've got the best quality hay we've ever had. We’ ve used it to make over 1,000 bales so far and have had only a few minor problems.”
Case IH 8540 baler
1 Best Buy0 Worst BuysRobin James, Laurel, Del.: “It makes nice bales under all conditions and hardly ever misses a tie,” reports Robin, owner of a 1988 Case-IH 8540 baler. “Bale uniformity is important to us because we pick up all of our bales with an automatic bale wagon,”
Case IH 8600 30-11 air drill
1 Best Buy0 Worst BuysGary Osborn, Fairmount, N.Dak.: “My 1990 Case-IH 8600 30-11. air drill is a best buy. Its accuracy, depth control, and ease of pulling and transport makes all other drills obsolete. It almost has the capacity of a grain bin. I can do as much or more in a day than I could do before with a 40-ft. drill.” A 1990 rock fork purchased from Ray’s Welding, Napoleon, N. Dak., “is builttough and works great.” Gary’s “worst buy” is his 1988 Case-IH 4900 45-ft. field cultivator, “The first year the wings cracked in welded seams, the shanks bent, and the shank spring holders broke. The second year the shank spring holders ripped out and the axle shaft broke. The company and dealer have stood behind the cultivator, replacing wings and broken shank holders.”
Case IH 8840 swather equipped
0 Best Buys1 Worst BuyDennis Andrews, Gate, Okla.: Dennis had poor luck with his 1990 Case-IH 8840 swather equipped with a 16-ft. header and double windrow attachment. “It cuts well, butthe double windrow attachmentis a joke because it doesn’t convey material as it should to double the windrow size. The reason was poor engineering on the hydraulic motor shaft that operates the canvas. I had to add a special-made key in order to make the system work under load, There's too much distance between the header and the front of the double windrow attachment for hay to be thrown, The engineers should spend some time in the field before sending out a machine like this,”
Case IH 900 6-row corn planter
1 Best Buy0 Worst BuysAndrew Spencer, Arkport, N.Y.: “My ‘best buy’ 1990 Case-IH 900 6-row corn planter works great. I used it to plant nearly 900 acres last spring with only a few minor problems.” Andrew says his 1989 Deere 9500 combine “has tremendous capacity. I felt it was somewhat underpowered, bul the company has solved the problem.” Ronald Bersie, Waverly, Minn,; “Itcuts down and tangled hay with ease and makes anice windrow,” says Ronald, pleased with his 1990 New Holland 499 hydro swing haybine.
Case IH 900 8-row planter
1 Best Buy0 Worst BuysJoe Appling, Crosbyton, Texas: A Case-IH 900 8-row planter rates as Joe’s “best buy”. “It'll plant in any kind of ground just like the company says.”
Case IH 900 Cyclo 6-row no-till corn
1 Best Buy0 Worst BuysNorman Rozendaal, Monroe, Iowa: Norman's happy with his 1990 Case-IH 900 Cyclo 6-row no-till corn planter. “It has performed beyond my highest expectations and plants accurately and at the correct population even at high planting speeds, It lets me plant soybeans by the number of plants per acre instead of pounds per acre. Maintenance is low,” On the “worst buy” side, “My Snapper LT 11 riding lawn mower is a piece of junk. It doesn’t stand up to ordinary farm yard use. The springs that hold the drive discs together failed so it wouldn't go forward and the handle that’s used to adjust deck height broke off. The cable that holds the flip-top hood over the engine broke causing the hood to fall forward on the ground, breaking the headlight wires.”
Case IH 900 Early riser 12row planter
1 Best Buy0 Worst BuysJim Mitchell, Eaton, Ohio: Jim's happy with his 1990 Case-IH 900 Early Riser 12row 30-in. planter. “It’s a dream come true. Seed placement is outstanding - it'll plant conventional or no-till equally well, Crusting doesn’t seem to be a problem either. The air metering system is simple, easy to fill, and unbelievably accurate. You can figure out how much seed you'll need for a field and that’s exactly what you'll use.” John Shults, Henderson, Md.; "My 1989 Chore-Time automatic feed system bought for a broiler house is a best buy. I've replaced only one motor and one auger bearing at a total cost of $120 - not bad for 7 1/2 years of continuous use."
Case IH 9250 4WD tractor
1 Best Buy0 Worst BuysChuck Grimes, Dumont, Minn.: Chuck's “best buy” is his Case-IH 9250 4WD tractor, “It’s easier to service than the 9150 model and has about 20 more hp. The cab is also much more quiet.”
Case IH Cyclo planter
1 Best Buy0 Worst BuysDean Begg, Columbus Grove, Ohio: “My 1990 Case-IH Cyclo planter works great. It’s simple to adjust and the settings are right on,”
Case IH Cyclo 900 6-row air planter
1 Best Buy0 Worst BuysStanley Ohol, Cambria, N.Y.: Stanley likes his Case-IH Cyclo 900 6-row air planter. “It's a simple planter. Well-built and it lets us plant fast.”
Case IH Magnum tractor 885
1 Best Buy0 Worst BuysJohn Miller, Howard City, Mich.: “My worst buy ofall time wasa Generac standby generator. After problems developed I got no help at all from the manufacturer or distributor. I took it to the authorized repair shop once and had them out to the farm twice. I gotonly about three hoursof service from it before I traded for another brand. “Tlike my Case-IH Magnum tractor, 885 loader tractor, 4800 Vibra Shank field cultivator, 496 cushion gang disk, and 2-row chopper equipped with electric controls.”
Case Ingersoll subcompact garden tractors
1 Best Buy0 Worst Buys“My 2011 Cub Cadet LT1042 riding mower had multiple problems with spindles and bearings as well as belts jumping off. The Kohler engine blew at 142 hours.
“My Case Ingersoll subcompact garden tractors are well built and hydraulic-operated with many attachments available. They’re made under the Ingersoll name by Eastman Industries. These are great tractors, not box store junk.”
Case Magnum 7220 tractor
1 Best Buy0 Worst Buys“In 2010 we bought a 1994 Case Magnum 7220 tractor used with about 10,500 hrs. on it. It had been worked hard by the original owner, who was a contractor. At about 15,500 hrs. we rebuilt the engine and transmission.
“This tractor has been worth every cent we paid for it. If we want more power we shut the tractor down, reset the fuel screw, and 10 min. later we’re back in action and up 2 gears, with a 6 percent increase in fuel usage and a 30 percent increase in productivity. The job takes only 10 min. in the field with 3 tools. Try to do that with modern tractors and see what it costs.
“The tractor now has about 17,000 hrs. on it, but is more than able to keep working. I had green blood in me until I bought this old tractor. It’s not full of wires and computer plugs, so if we have a problem we can find it and fix it. I wish they made new high horsepower tractors like this.”
Case MX110 tractors
1 Best Buy0 Worst Buys“I have three 2001 Case MX110 tractors and they’re all best buys. I use them for commercial ditch mowing. Last year we cut more than 14,000 acre of ditches and only had two days of down time with one tractor. I really like the 5.9-liter Cummins engine. It’s very economical.”
Case MXV 125 tractor
1 Best Buy0 Worst Buys“My 2004 Case MXV 125 tractor has had one electronic problem after another. It has spent more time at the dealer than in the field. The problems were never resolved, so we traded for a stripped-down Case MXM 40 equipped with a standard shift transmission. No problems. Our 1971 Case 870 has more than 10,000 hours on it. We still use it to do light work all summer long.”
Case Now ithas 5
1 Best Buy0 Worst BuysMichael T. Mayer, Manhattan, Kan.: “I'll never recommend a Ford pickup to anyone [ like,” says Michael, disgruntled owner of a 1989 F-150 XLT Lariat 4-WD equipped with a 5.0-liter V-8 engine and 5-speed manual overdrive transmission, “The pickup wasn't aligned right from day one. The engine didn't use any oil in the first 1,000 miles, but now it uses one quart every 800 miles and is getting worse. At 1,500 miles a bearing went out on the transfer case. Now ithas 5,700 miles and things aren't improying. It's supposed to get 17 mpg but it gets only 13 mpg at best. I bought the pickup out of town and made the mistake of asking the local dealer to repair it. He had it for three days, leaving me to find my own transportation, and did poor service work. He said that according to Ford regulations, the oil usage was within tolerance levels, In fact, Ford says it’s tolerable for an engine to use one quart of oil every 600 miles, I put 114,000 miles on my 1982 Chevrolet diesel pickup and never used one quart of oil in 3,000 miles. The dealer says he'll look at it again when it has 7,500 miles. If Ford had a ‘satisfaction guaranteed or yourmoncy back’ offer, I'd jump at it in a heartbeat.”
Case S-128
1 Best Buy0 Worst BuysRobert Himmerich, Pena Blanca, N.M.: Robert's “best buy” is a tillage tool he made out of a 1950's Case S-128 disk. 1ys “We replaced the rear disk gangs with a pair of 2 1/2-in. sq. toolbars which we fitted with 11 Allis-Chalmers field cultivator spring tines with twisted chisel points. They throw soil back toward the center of the disk. The center ridge is broken up by a straight chisel point. For less than $400 we now have an excellent piece of conservation tillage equipment. “My Vac-A-Way seed and grain cleaner/ grader is my worst buy. It doesn’t develop enough vacuum power to remove light material from the grain. To get acceptably clean seed we have to run grain through it at least three times. We had to reinforce the bagger-elevator in order to keep the sheet metal from collapsing onto the elevator belts and jamming them. For a little more money we could have bought a much better rig.”
Case SC tractor
1 Best Buy0 Worst Buys“My best buy ever is my 1941 Case SC tractor. I don’t even have to choke it to start it. I just press the starter button and it starts right up every time. It’s a reliable, well-built tractor.”
Case SR250 skid steer
1 Best Buy0 Worst BuysArlin’s best buy is his 2015 Bobcat S770 skid-steer. “We put about 1,000 hrs. a year on our machines, so we need a good, dependable skid loader. With 2,400 hrs. so far, we’ve had no problems. We have a good dealer for and parts service.”
The Ozark Trail 1/2-gal. stainless steel water jug is another great buy. “I took the jug with ice water when I went fishing for 8 hrs. in 90 degree heat.When I got home, there was still ice inside!
“My 2013 Case SR250 skid steer kept going down. The wiring harness shorted out and ruined the ECU. One of the connector plugs shorted out. It took the mechanic 2 days to fix the plug. He told me to get rid of it because there are too many other electrical problems to list. That was 1,900 hrs. of headache.”
Case TH earth metal disc
1 Best Buy0 Worst BuysAllan Augustine, Port Colborne, Ontario: “It works great,” says Allan, owner ofa 1984 Krause 23-ft. disk equipped with cushion front gangs and Case-TH earth metal disc plates, Allan also likes his 1988 International 720 5-16 auto-reset plow. “It does an excellent job in both sod and stubble and is a pleasure to use under all conditions.”
Case TH 1640 combine
1 Best Buy0 Worst BuysRuss Keast, Henderson, Iowa: “The only problem we've had with it is hauling the grain away fast enough,” says Russ, pleased with his “best buy” 1988 Case-TH 1640 combine. “This combine is unbelievable in its simplicity, capacity, smoothness of operation, grain quality and operator comfort. “Another best buy is my 1988 M & W 72-in. zero-turn diesel lawn mower. The deck is out front and can maneuver it anywhere. It makes yard work fun,”
Case TH 1680 combine
1 Best Buy0 Worst BuysRobert Lungren, Worland, Wyo.: “It’s easy to operate and maintain, and the controls are close at hand,” says Robert, whose 1987 Case-TH 1680 combine has nevertheless had some problems, “It should have a higher output alternator. Halfway through the harvest season I have to recharge the batteries because the alternator can’t keep up with the electrical demands. The original alternator had 90 amps. The dealer gave us an updated version with 110 amps, but it still isn’t powerful enough. It should have at least 150 amps.”
Case TH 385 tractor
1 Best Buy0 Worst BuysBob Corbin, Finksburg, Md.: Bob likes his 1987 35 hp Case-TH 385 tractor. “It’s fuel efficient and heavy enough to carry big bales. Starts well in cold weather. No problems.”
Case TH 4800 field cultivator heads
1 Best Buy0 Worst BuysLarry Beyer, Marengo, Iowa: Larry says his Case-TH 4800 26-ft. field cultivator heads his “best buy” list. “It has excellent clearance and never plugs in disked corn stalks. It also folds for transport so can get it through a 16-ft. wide gate.”
Case TH 496 disk
1 Best Buy0 Worst BuysChris Malott, Bethel, Ohio: Chris's “best Buy” is His 1989 Case-TH 496 22-ft. disk. “It has excellent penetration and does a good job leveling the soil. The only problem I’ ve had is with the hangers for the rock flex springs. “My 1989 Ford F-2504-WD pickup was the best riding heavy duty truck I ever drove, but had a terrible paint job and poor fuel efficiency. The 351 cu. in, engine with 5-speed overdrive transmission got only 10 1/2 mpg on a good day, traded it in for a diesel.”
Case TH 8520 square baler saves
1 Best Buy0 Worst BuysBernard Hartman, Corning, N.Y.: Bernard says his 1990 Case-TH 8520 square baler saves many more leaves than conventional balers and is a “best buy”. “It makes nice uniform bales. There’s no side draft on hills and no need to adjust the tongue for highway travel.”
Case TH 900
1 Best Buy0 Worst BuysGene Wiemers, Melbourne, Iowa: Gene's happy with his 1989 Case-TH 900 series 12-row 30-in. semi-mounted planter. “It’s well built and plants accurately. I set it to plant eight 36-in. rows of com. For soybeans I add extra units to plant fifteen 36-in, rows with I$-in. skip rows. The big seed hoppers save a lot of work, and the trash whippers and depth gauge wheels work great.”
Case VAC tractor
1 Best Buy0 Worst Buys“I’m well into my 80’s so I’ve had a lot of best buys over the past 60 years. My first new vehicle was a 1947 Studebaker pickup that looked much like the restored one shown in the photo. Over the years I owned several Studebaker pickups and put more than 200,000 miles on many of them.
“My 1947 Case VAC tractor has had a couple of valve jobs but has never been overhauled. I still use it a lot. My 1954 Ford Major diesel tractor from England has more than 20,000 hours on it and ran like new until a few weeks ago, when a crankshaft broke. My 1949 Chevrolet light duty pickup has more than 450,000 miles on it. My 1956
Case XL40 skid steer loader
1 Best Buy0 Worst Buys“After 800 hours of use my Case XL40 skid steer loader still performs like new.”
Case broke
0 Best Buys1 Worst BuyGeorge Janecek, Washington, Iowa: A 1992 Titan flatbed gooseneck “beavertail” trailer equipped with dual wheels and two 9,000-Ib. axles heads George's “best buy” list. “We use it to haul lumber, steel, hay, and equipment. Last spring we puta 1,500gal. starter fertilizer tank on it and used it to haul a day’s supply of seed to the field.” On the “worst buy” side, George lists his 1991 Ford F-250 4-WD extended cab pickup. “At 22,000 miles the transmission failed and left me stranded on the road. At 28,000 miles the transfer case broke and I was stranded again, this time with a gooseneck trailer full of hogs. At 32,000 miles one of the front hubs broke. At 34,000 miles the anti-lock brake sensor broke, and at 38,000 miles the ‘check engine’ gauge on the dash began to flash. The rear seat is mounted too low to be comfortable. I’ve used it only onthe highway, never forchores. “Tuse my best buy 1981 Chevrolet pickup to do chores, It has 145,000 miles and the transmission is original.”
Case vacuum control
1 Best Buy0 Worst BuysRuth Pullman, Alma, Mich.: Ruth’s unhappy with her 1989 Chevrolet 3/4-ton 4-WD pickup equipped with a 350cu. in. V8 engine. “It blew a head gasket in the first 33,000 miles. Three of our friends and neighbors have had the same problem. It happens on both 6 and 8-cylinder engines. The transfer case, vacuum control, and front wheel drive seals also had to be replaced, and each time we had to pay $100. The warranty should have fully covered the repairs.”
Case knife
1 Best Buy0 Worst Buys“I do a small amount of wood carving. I’ve had good luck with Old Timer and Buck pocket knives. A year or two ago, I bought a Case knife (top-of-the-line, made in the USA). I call it my ‘hunk of junk’ as the blades were loose and wiggly from day one.
“Stihl tools (chainsaws, weed eaters, etc.)
Case there's
1 Best Buy0 Worst BuysNed Collin, Purcell, Okla.: Ned nominates his 1990 Massey Ferguson 828 round baler as a “best buy”. “It lets me bale hay directly behind my swather to make round bale haylage, and it makes an equally nice bale on very dry, weedy grass hay. In either case there's no problem starting a bale, It's easy to operate. “My worst buy is Nationwide 6-volt batteries made in Fort Worth, Texas. They won't hold a charge. I went through four batteries before realizing that the problem wasn't my tractor. I installed a different battery brand and have had no more problems.”
Case went
1 Best Buy0 Worst BuysGale Carpenter, Union City, Mich.: “What can you buy American-made that's any good?”, asks Gale, unhappy owner of several American-made pickups. “The rear differential on my 1988 Chevrolet 2500 4WD went out three times in 10,000 miles and the brakes failed at 22,000 miles. I traded it for a 1989 Ford F-250 4-WD equipped with a 351 cu. in. gas engine which didn’t run right from day one. At 22,000 miles the transfer case went out and the seals on the front differential started leaking. I wanted to trade it for a Dodge diesel, but I couldn’t get delivery for six months so I traded for a 1990 Ford F-250 5speed diesel. The synchronizers went out of fourth gear within 2,800 miles. My wife and daughter have both owned Toyota 4-WDs and ran them 100,000 miles without any problems. They both just bought new Toyota 4-WDs and the salesman told us that Toyota might come out with a full size pickup in two years. If it’s as good as their small pickups it'll be ‘see ya’ for the big three auto makers. If it’s true about the Japanese owning us, who do we have to blame?”
Read every report in full
FARM SHOW has run reader Best & Worst Buys since the beginning.