Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Porter-Cable › circular saw

Porter-Cable circular saw

What FARM SHOW readers say · 1 Best Buy1 Worst Buy · Chainsaws & Saws

Porter-Cable circular saw

1 Best Buy1 Worst Buy
Worst Buy
Lowell Patterson, Eighty-Four, Penn. · Vol. 26, No. 2 (2002), p. 16

“Lowell’s impressed with Kroil, a penetrating lubricant (Kano Laboratories, Box 110098, Nashville, Tenn. 37222 ph 615 833-4101; Website: www.kanolabs.com). “I used it mixed with 30-weight non-detergent motor oil to repair a badly rusted 1982 Ford pickup. The pickup’s kingpin began to seize a while ago which caused increased binding and made it hard to steer. The grease zerk wouldn’t take grease. I couldn’t justify the proper repairs so I was in a real fix.

“I sprayed Kroil into the yoke seams, jacked up the wheel, and worked the lubricant in by steering right and left with the engine running. I waited 15 minutes or so but there didn’t seem to be any improvement so I went into the house. Two hours later, when I went back out and got in the pickup I noticed right away that it steered much easier. I had to repeat the treatment twice more over the next few days before the grease zerk began to take grease.

“I used this same procedure on an old Ford F600 freight truck that belonged to a cousin. The truck was almost unsteerable, and he had to drive it from Pennsylvania to California. I applied Kroil to all the linkage and joints which solved the problem in short order. The company claims Kroil will creep into a joint as tight as one millionth of an inch. It sure helps on tight stuff.

“Our Jonsereds turbo chain saw is a best buy. The only repair it has needed was to the crank assembly. Otherwise this chain saw has performed superbly.

“My Porter-Cable circular saw and 1/2-in. heavy duty drill are both outstanding tools. I do a lot of home improvements so I can’t tolerate poor performance in power tools.

“I want to warn readers to avoid power drills with Rohti German-made drill chucks - I can guarantee they will fail. These chucks are found mostly on 1/2-in. hammer drills sold by Milwaukee, Bosch, Dewalt, and Sears Craftsman. The problem is that the chuck weakens rapidly to the point where it’s impossible to keep it tight for even a few revolutions. If anyone has such a tool they should remove the chuck, send it back to the tool manufacturer, and ask for an American-made chuck. I did that for a Milwaukee drill and got a good chuck.

“I’m intrigued with Hammerite paint (MasterChem, Box 368, Barnhart, Mo. 63012 ph 800 325-3552). It might be the only paint that can be successfully painted directly over rust. It has powdered glass in it which makes it durable.“ 3,500 miles. It uses less than a half quart of oil between oil changes.”

Best Buy
Donald Burton, Glen Arm, Md. · Vol. 21, No. 5 (1997), p. 15

“My 1996 Porter Cable reciprocating saw is my best buy. It’ll cut wood, metal, etc., and start blind cuts. The ‘quick change’ blade chuck is fast and convenient and has been trouble-free. It’s a good feature.”

Own a Porter-Cable? Tell FARM SHOW how it’s held up.

Your report could appear in a future issue.

Send your Best or Worst Buy

More Porter-Cable products

Porter-Cable air compressor 0 best · 2 worstPorter-Cable 20-volt circular saw 5 best · 1 worstPorter-Cable electric tools 2 best · 0 worstPorter Cable 18-volt cordless tool set 4 best · 0 worst

See all Porter-Cable reports →