Real farmers rate what they bought, from FARM SHOW MagazineSubscribe  ·  Free issue  ·  Send us your Best or Worst Buy
Subscribe to FARM SHOW
Home › Brands › Millermatic

Millermatic: what farmers say

8 reports in FARM SHOW · 7 Best Buys1 Worst Buy

Millermatic 141 MIG Welder

1 Best Buy0 Worst Buys
Best Buy
Jeff Lang, Newport News, Va. · Vol. 46, No. 4 (2022), p. 13

“After using a Flux Core welder for several years, I finally decided to upgrade. After some research, including reviews and YouTube videos, I purchased the Millermatic 141 MIG Welder. I’m really impressed and totally satisfied with this welder. I made a wooden frame to hold gas bottles in place and straps to hold it secure.”

Millermatic 200 wirefeed welder

1 Best Buy0 Worst Buys
Best Buy
Terry J. Glasheen, Oshkosh, Wis. · Vol. 21, No. 5 (1997), p. 16

“It makes welding sheet metal really easy and also does a good job on heavier pieces,” says Terry, pleased with his Millermatic 200 wirefeed welder.”

Millermatic 210 MIG welder

1 Best Buy0 Worst Buys
Best Buy
Matt Silveira, Placerville, Calif. · Vol. 41, No. 3 (2017), p. 14

“My 2003 Millermatic 210 MIG welder performs well on a variety of materials including steel and aluminum (with spool gun). It’s easy to maintain, load, and operate. It even works well for making difficult vertical and out-of-position welds. I haven’t had to replace any wearable parts except for the torch nozzle and wire feed tip.

“My worst buy was my Husqvarna 22 hp. riding mower equipped with a V-twin engine and hydrostatic transmission. After just 50 hrs. of use the plastic pulleys that tension the mower deck belt and drive belt both failed. The ‘permanent’ sealed bearings lost lubricant, which caused the pulleys to seize so that they melted and burned through the belts. I had to replace them with steel pulleys with maintainable bearings in order to use the mower again. Then at 60 hrs. the mandrels that drive the mower blades cracked. Upgraded mandrels weren’t available so I replaced the original ones and sold the mower at a loss.”

Millermatic 211 mig welder

1 Best Buy0 Worst Buys
Best Buy
Bill Finkbone, Clarksville, Ohio · Vol. 44, No. 5 (2020), p. 14

“It didn’t take long for my Millermatic 211 mig welder to pay for itself. It operates on 120 or 240 volts and can handle big jobs on low voltage. This welder is easy to set up and has excellent arc characteristics. I keep it in my pickup and use it almost every day.”

Millermatic 211 MIG welder

1 Best Buy0 Worst Buys
Best Buy
Lyndon Miller, Shipshewana, Ind. · Vol. 43, No. 2 (2019), p. 14

“I couldn’t get my Lincoln 180 welder to do a good job, so at my uncle’s suggestion I bought a new Millermatic 211 MIG welder. I liked it so much that I ended up trading the Lincoln for another used Millermatic 211.”

On the “worst buy” side, he lists his 2017 Troy-Bilt rear tine tiller. “After we bought a new place we needed a rototiller for our garden, so I paid $700 for this reverse tine tiller. However, it didn’t work well in our sandy soil as I had to push the tiller forward just to keep it from getting stuck. I ended up selling it a year later for $150.”

Millermatic 250 Mig welder welds

1 Best Buy0 Worst Buys
Best Buy
Steven M. Yoder, Reedsville, Penn. · Vol. 39, No. 5 (2015), p. 15

“My Miller Spectrum 625 plasma cutter cuts up to 5/8-in. thick steel, and my Millermatic 250 Mig welder welds up to 1/2-in. material. Both work great.

“My Northern Tool 200 amp AC stick welder and my 140 wire welder were both worst buys.”

Millermatic 250X wire welder equipped

0 Best Buys1 Worst Buy
Worst Buy
Larry Don Dewey, Medford, Okla. · Vol. 24, No. 5 (2000), p. 16

Larry’s impressed with his 1999 Ford F-250 Super Duty extended cab, shortbed pickup equipped with a diesel engine and 6-speed manual transmission. “I like the way it handles. The diesel engine has a lot of power and is economical to operate. The cab offers a good view and the four doors are handy for passengers. However, I’m disappointed with all the wind noise in the cab. My 1992 Ford pickup is much quieter.

“My worst buy is my 2000 Millermatic 250X wire welder equipped with gauges. I’m very disappointed with it. We have an old Millermatic 200 that has been trouble-free. The spool of wire on the 250 won’t turn freely. The problem is that it catches on a bolt head that should have been countersunk. The factory sent me a kit to correct the problem. The voltage varies whenever I try to weld. It’s either hot or cold and won’t hold an arc. The voltage and wire feed charts are located on the inside of the door so every time you want to check the settings you have to open the door. The charts should be on the outside of the door. Also, the 200 model does a much smoother job of welding than this one.”

MillerMatic 35 wire feed welder

1 Best Buy0 Worst Buys
Best Buy
Brad Trelka, Junction City, Wis. · Vol. 35, No. 3 (2011), p. 14

“I like my 1983 MillerMatic 35 wire feed welder. I use it almost every day. One time I melted the leads right off. I took the welder in to have it fixed, and it worked like new again. I’d recommend this welder to anyone.

“In 2009 I bought an Ingersoll Rand 13 hp portable air compressor from Northern Tool & Equipment. It’s equipped with a 30-gal. tank and a Honda engine that delivers 25 cfm at 175 psi. I ordered the unit in May but didn’t receive it until October 15.

“Once I started the compressor it ran for only about 30 seconds before the drive belt flew off. I aligned the pulleys and put the belt back on, and it worked a little longer. I did everything according to the owner’s manual but got no help from Northern Tool. We were becoming the laughing stock of service trucks in our area because a tank of gas in the truck would last longer than the belts on the compressor.

“I had to borrow a compressor from a customer, while the shiny new compressor on my truck was nothing more than a boat anchor. I called Ingersoll Rand and they scheduled a technician to make a service call. The company wasn’t happy that I had bought the compressor from Northern Tool instead of from one of their sales outlets. The technician came out 3 or 4 times and found the pulley on the compressor was machined wrong so the belt wouldn’t ride in the sheave properly. He changed the pulley, but again the belt came off. Then the technician talked to an assembly line worker at the factory, who said the belt had the wrong tension level. We made an adjustment and that seems to have solved the problem. Now the compressor is out of warranty so I’m on my own. So far so good, though.

“My neighbor purchased a similar air compressor from Harbor Freight about the same time for $1,000, while mine cost $2,450. His compressor is made in China, but he says nothing has gone wrong and he’s well satisfied with it. I think we might want to rethink the American pride and quality of products.”

Read every report in full

FARM SHOW has run reader Best & Worst Buys since the beginning.

Subscribe to FARM SHOW