J-B Weld: what farmers say
6 reports in FARM SHOW · 4 Best Buys2 Worst Buys
J-B Weld (general)
4 Best Buys0 Worst Buys“I’ve fixed many things with J-B Weld. Two years ago, I fixed the block (motor) on my 20-year-old Dixon mower, which was another best buy. I’m disappointed they don’t make Dixon’s anymore.”
“Without question, J-B Weld is a best buy. I’ve used this product to patch or repair a vast array of items, ranging from filling a 10-in. external crack in the cast iron engine block on my Deere M to reattaching the handle on one of my wife’s stainless steel cooking pots. Just be sure the surfaces are clean and grease-free. Cleaning with acetone or lacquer thinner is recommended.”
“My best buy is J-B Weld (J-B Weld Co., Sulphur Springs, Texas ph 800 529-3530). I used this product to build up a worn cast iron axle housing on my tractor, and to build up a steel tiller shaft which was worn down due to a frozen bearing.”
On the “worst buy” side, “My Belarus 310 4-WD tractor equipped with a front-end loader is my worst buy. At 200 hours the hydraulic pump on it quit working. Now at 400 hours, the second pump has failed. The pump seems too small for the loader. The front axle broke and the bushing chewed up the cast housing. Apparently the set screws weren’t turned in far enough to keep the bushing from turning. The dealer wanted to sell me a whole new gear unit, explaining that he couldn’t get just a separate housing right away as there was a long waiting list for them. So I used J-B Weld to build up the housing.
“The broken axle also caused a driveshaft flange to get chewed up. I solved the problem by getting a flange with four holes instead of six, and then paying $30 to have six holes drilled into it. The brakes are almost impossible to adjust, and they’re too weak to handle filled tires as well as the weight of a front-end loader. Another problem is the lever for the 3-pt. lift is hard to control and can’t be moved slowly.”
J-B Weld rates as Alan’s “best buy” (J-B Weld Co., Box 483, Sulphur Springs, Texas 75483 ph 800 529-3530 or 903 885-7696).
“I still have the original package that I bought with the price sticker on it. I know I’ve saved hundreds and maybe thousands of dollars by using this product. It’s worth many times more than what it sells for,” says Alan. J-B Weld is sold as an inexpensive alternative to welding, soldering, and brazing and can be used to repair damaged welds and solders. It comes packaged in two tubes. One contains liquid steel/epoxy resin, and the other contains hardener. When mixed together in equal portions, a chemical reaction occurs that turns the mixture into a compound that’s said to be as hard and tough as steel.
Like metal, J-B Weld can be formed, drilled, ground, tapped, machined, filled, sanded, and painted. It stays pliable for about 30 minutes after mixing, sets in 4 to 6 hours, and cures fully in 15 to 24 hours chains to mess with.”
J-B Weld FiberWeld Permanent Repair cast
0 Best Buys1 Worst Buy“Like so many others, I’ve had great results with J-B Weld original steel reinforced epoxy with metals, wood and hard plastic. I apply a clamp if possible and put the glued object near a mild heat source for several hours to accelerate the cure.
“So, I was extremely disappointed that J-B Weld FiberWeld Permanent Repair Cast (an epoxy-saturated fiberglass tape single-use kit) totally failed to seal the leak from a short hairline split in 1-in. pvc garden irrigation pipe. The pipe surface was clean, dry, and lightly sanded. All instructions were carefully followed, and the pipe cured overnight. Water under minimal pressure immediately leaked from both ends of the wrap. There was absolutely no adhesion of epoxy to the pvc.”
J-B Weld original steel reinforced
0 Best Buys1 Worst Buy“Like so many others, I’ve had great results with J-B Weld original steel reinforced epoxy with metals, wood and hard plastic. I apply a clamp if possible and put the glued object near a mild heat source for several hours to accelerate the cure.
“So, I was extremely disappointed that J-B Weld FiberWeld Permanent Repair Cast (an epoxy-saturated fiberglass tape single-use kit) totally failed to seal the leak from a short hairline split in 1-in. pvc garden irrigation pipe. The pipe surface was clean, dry, and lightly sanded. All instructions were carefully followed, and the pipe cured overnight. Water under minimal pressure immediately leaked from both ends of the wrap. There was absolutely no adhesion of epoxy to the pvc.”
Read every report in full
FARM SHOW has run reader Best & Worst Buys since the beginning.